HP 5973 Mass Selective Detector Manuals

Manuals and User Guides for HP 5973 Mass Selective Detector. We have 2 HP 5973 Mass Selective Detector manuals available for free PDF download: Hardware Manual, Hardware Installation Manual

HP 5973 Hardware Manual (297 pages)

Mass Selective Detector

Brand: HP | Category: Security Sensors | Size: 6.7 MB

Table of Contents
7
Chapter 1 Installing GC Columns

20
Chapter 2 Operating the MSD

31
Chapter 3 Troubleshooting the MSD

68
Chapter 4 Maintaining the MSD

93
- Before Starting
  
  94
- Maintaining the Vacuum System
  
  101
  - To Check and Add Foreline Pump Oil
    102
  - To Drain the Foreline Pump
    104
  - To Refill the Foreline Pump
    106
  - To Replace the Oil Trap
    108
  - To Check the Diffusion Pump Fluid
    110
  - To Separate the MSD from the GC
    112
  - To Remove the Diffusion Pump
    114
  - To Replace the Diffusion Pump Fluid
    116
  - To Reinstall the Diffusion Pump
    118
  - To Reconnect the MSD to the GC
    120
  - To Remove the Calibration Vial
    122
  - To Refill and Reinstall the Calibration Vial
    124
  - To Remove the Foreline Gauge
    126
  - To Reinstall a Foreline Gauge
    128
  - To Remove the Calibration Valve
    130
  - To Reinstall a Calibration Valve
    132
  - To Replace the Fan for the High Vacuum Pump
    134
  - To Remove the Triode Gauge Tube
    136
  - To Reinstall a Triode Gauge Tube
    138
  - To Lubricate the Side Plate O-Ring
    140
  - To Lubricate the Vent Valve O-Ring
    142
- Maintaining the Analyzer
  
  144
- Maintaining the GC/MSD Interface
  
  172
  - To Remove the GC/MSD Interface Heater and Sensor
    173
  - To Reinstall the GC/MSD Interface Heater and Sensor
    175
- Maintaining the Electronics
  
  177
  - To Adjust the RF Coils
    179
  - To Replace the Primary Fuses
    181
Chapter 5 Vacuum System

183
- Diffusion Pump MSD Vacuum System
  186
- Turbo Pump MSD Vacuum System
  187
- Diffusion Pump Vacuum Manifold
  188
- Turbo Pump Vacuum Manifold
  189
- Side Plate
  190
- Vacuum Seals
  192
  - Face Seals
    192
  - KF (NW) Seals
    192
  - Compression Seals
    192
  - High Voltage Feedthrough Seal
    193
- Foreline Pump
  194
- Foreline Gauge
  196
- Diffusion Pump and Fan
  198
- Turbomolecular Pump and Fan
  202
- Calibration Valve and Vent Valve
  204
  - Calibration Valve
    204
  - Vent Valve
    204
- Triode Gauge Tube
  206
- Gauge Controller
  208
Chapter 6 GC/MSD Interface

211
Chapter 7 Analyzer

218
- Ion Source
  218
  - Ion Source Body
    218
  - Filaments
    219
    
    Filament Selection
    219
    
    Electron Energy
    220
    
    Emission Current
    220
    
    Filament Care
    221
  - Magnet
    221
  - Repeller
    221
  - Drawout Plate and Cylinder
    222
  - Ion Focus
    222
  - Entrance Lens
    222
    
    Entrance Lens Gain
    222
    
    Entrance Lens Offset
    222
- Mass Filter
  223
  - AMU Gain
    223
  - AMU Offset
    224
  - 219 Width
    224
  - DC Polarity
    225
  - Mass (Axis) Gain
    225
  - Mass (Axis) Offset
    225
  - Quadrupole Maintenance
    226
- Detector
  227
  - Detector Focus Lens
    227
  - High Energy Dynode
    227
  - Electron Multiplier Horn
    227
- Analyzer Heaters and Radiators
  230
Chapter 8 Electronics

236
- Side Board
  236
- Electronics Module
  237
- Main Board
  238
- Signal Amplifier Board
  239
- HP-IB/MS Control Card
  240
- AC Board
  241
  - Pumpdown Safety Shutdown
    242
- Power Supplies
  243
  - Low Voltage (Ac-DC) Power Supply
    243
  - High Voltage (HED) Power Supply
    243
- Toroid Transformer
  244
- Back Panel and Connectors
  245
  - Remote Start Connector
    245
  - I/O (HP-IB) Connector
    245
  - HP-IB Address Switch
    245
- High Vacuum Signal ( HIVAC SIGNAL ) Connector
  
  246
  - Foreline Pump Power Cord Receptacle
    246
- High Vacuum Power Connector
  
  246
  - Hivac Power
    246
  - Power Cord Receptacle
    246
  - Primary Fuses
    246
  - Interfacing to External Devices
    248
    
    Remote Control Processor
    248
    
    Remote Start Signals
    248
    
    Start Run Input
    249
    
    System Ready
    249
  - Status Display and Power Switch
    250
    
    Analyzer Status LED
    250
    
    Cal Valve Status LED
    250
    
    Power Status LED
    250
    
    Power Switch
    250
  - Turbo Pump Controller
    252
    
    Electronics
    256
    
    Vacuum System
    260
    
    Analyzer
    268
    
    GC/MSD Interface
    274
    
    Consumables and Maintenance Supplies
    276

HP 5973 Hardware Installation Manual (46 pages)

Mass Selective Detector

Brand: HP | Category: Security Sensors | Size: 0.61 MB

Table of Contents
3
Chapter 1 General Information

5
- Introduction
  6
- Customer Responsibilities
  8
- Site Requirements
  9
  - Space Requirements
    9
  - Telephone
    9
  - Environmental Requirements
    9
  - Power Requirements
    10
  - Gases
    10
- Other Documentation
  13
Chapter 2 Installation

16
Chapter 3 Checklists

35
- Installation Checklist
  36
- Customer Familiarization Checklist
  40

HP Categories

Desktop

Laptop Server

Monitor

Switch

More HP Manuals

HP 5973 Mass Selective Detector Manuals

HP 5973 Hardware Manual (297 pages)

Table of Contents

Chapter 1 Installing GC Columns

Chapter 2 Operating the MSD

Chapter 3 Troubleshooting the MSD

Chapter 4 Maintaining the MSD

Before Starting

Maintaining the Vacuum System

Maintaining the Analyzer

Maintaining the GC/MSD Interface

Maintaining the Electronics

Chapter 5 Vacuum System

Chapter 6 GC/MSD Interface

Chapter 7 Analyzer

Chapter 8 Electronics

High Vacuum Signal ( HIVAC SIGNAL ) Connector

High Vacuum Power Connector

HP 5973 Hardware Installation Manual (46 pages)

Table of Contents

Chapter 1 General Information

Chapter 2 Installation

Chapter 3 Checklists

Related Products

HP Categories