Table of Contents
Advertisement
Quick Links
AIR CONDITIONER (MULTI-SPLIT TYPE)
Installation Manual
Indoor Unit
Model name:
<Concealed Duct Type>
RAS-M07G3DV Series
RAS-M10G3DV Series
RAS-M13G3DV Series
RAS-M16G3DV Series
EG55760001-00
English
Español
Français
Italiano
Deutsch
Português
Ελληνικα
Türkçe
Polski
Česky
Русский
Hrvatski
Magyar
Nederlands
Svenska
Suomi
Norsk
Dansk
Română
Български
Eesti
Latviski
Slovenčina
Slovenščina
Advertisement
Table of Contents
Related Manuals for Toshiba RAS-M07G3DV Series
Summary of Contents for Toshiba RAS-M07G3DV Series
-
Page 1: Installation Manual
AIR CONDITIONER (MULTI-SPLIT TYPE) Español Installation Manual Français Italiano Deutsch Português Indoor Unit Ελληνικα Türkçe Model name: Polski <Concealed Duct Type> Česky RAS-M07G3DV Series Русский RAS-M10G3DV Series Hrvatski Magyar RAS-M13G3DV Series Nederlands Svenska RAS-M16G3DV Series Suomi Norsk Dansk Română Български... -
Page 2: Table Of Contents
– 1 – Installation Manual Contents Precautions for safety The manufacturer shall not assume any liability for the damage Precautions for safety ........1 caused by not observing the description of this manual. - Page 3 Installation Manual • THIS AIR CONDITIONER USES THE NEW HFC REFRIGERANT THIS INSTRUCTION CAN RESULT IN FIRE OR EXPLOSION. (R410A), WHICH DOES NOT DESTROY THE OZONE LAYER. • TO PREVENT OVERHEATING THE INDOOR UNIT AND R410A refrigerant is apt to be affected by impurities such as water, CAUSING A FIRE HAZARD, PLACE THE UNIT WELL AWAY oxidizing membranes, and oils because the pressure of R410A (MORE THAN 2 M) FROM HEAT SOURCES SUCH AS...
- Page 4 – 3 – Installation Manual of conventional refrigerant (R22). Use the specified pipe parts, and • Do not select a location for installation where there may be ensure correct installation, otherwise damage and/or injury may be excessive water or humidity, such as a bathroom. Deterioration of caused.
- Page 5 Installation Manual wiring method etc.) • Follow the instructions in this installation manual to arrange the • Places where iron or other metal dust is present. If iron or other drain pipe for proper drainage from the unit. Ensure that drained metal dust adheres to or collects on the interior of the air water is discharged.
-
Page 6: Accessory Parts
– 5 – Installation Manual Accessory parts Selection of installation place Avoid installing in the following places Part name Q’ty Shape Usage Select a location for the indoor unit where the cool or warm air will circulate evenly. Installation Manual This manual (Be sure to hand over to customers) Avoid installation in the following kinds of locations. -
Page 7: Installation Space
Installation Manual Installation under high-humidity atmosphere <Under air intake> <Back air intake> In some cases including the rainy season, especially inside of the ceiling may become high-humidity atmosphere (dew-point temperature: 23 °C or higher). 1. Installation to inside of the ceiling with tiles on the roof Air inlet 2. -
Page 8: Installation
– 7 – Installation Manual Installation • To move the indoor unit, hold the hooking brackets (4 positions) only. CAUTION • Do not apply force to the other parts (refrigerant pipe, drain pan, foamed parts, resin parts or other parts). Strictly comply with the following rules to prevent damage of the •... -
Page 9: Installation Of Indoor Unit
Installation Manual Installation of hanging bolt Installation of indoor unit Side view • Consider the piping / wiring after the unit is hung to Treatment of ceiling determine the location of the indoor unit installation Incorrect The ceiling differs according to structure of building. and orientation. - Page 10 – 9 – Installation Manual Installation location of receiving unit 3. Connect the housing of Signal receiving unit with the connector of wires extended from the indoor unit. (Fig. 2) The sensor of indoor unit with wireless remote controller can receive a signal by distance within approx. 8 m. 4.
-
Page 11: Drain Piping
Installation Manual Drain piping Pipe material, size and insulator The following materials for piping work and insulating process are procured locally. CAUTION Pipe material Hard vinyl chloride pipe VP25 (Nominal outer diameter Ø32 mm) Insulator Foamed polyethylene foam, thickness: 10 mm or more Following the Installation Manual, perform the drain piping work so Connection of drain hose that water is properly drained. - Page 12 – 11 – Installation Manual Insert the flexible drain hose into the lower drain pipe • After checking that the water drains and there are no water leaks, turn off the power, connect the float switch and fix it with the hose band. connector to its original location (CN34) on the P.C.
-
Page 13: Duct Design
Installation Manual Duct design Arrangement Referring to the following dimensions, manufacture duct at the local site. M07,10,13G3DV M16G3DV <Under air intake> <Under air intake> <Back air intake> <Back air intake> EN-23 – 12 – EN-24... -
Page 14: Fan Characteristics
– 13 – Installation Manual Fan characteristics RAS-M07G3DV, M10G3DV Series RAS-M16G3DV Series Standard Air Volume = 780m Standard Air Volume = 570m Upper limit of external Upper limit of external static pressure (45Pa) static pressure (45Pa) High (45Pa) High (45Pa) Lower limit of external static pressure (45Pa) Lower limit of external... -
Page 15: Refrigerant Piping
Installation Manual Refrigerant piping Connecting method of the duct Connect a duct to the Projection margin in flaring: B (Unit: mm) CAUTION outside of the flange. In addition, the duct must be covered with insulation Outer dia. of R410A tool Conventional Duct: Insulation material When the refrigerant pipe is long,... -
Page 16: Electrical Connection
– 15 – Installation Manual Electrical connection • Use the tightening torque levels as listed in the table REQUIREMENT below. 1. The supply voltage must be the same as the rated voltage of the air conditioner. Outer dia. of • Apply the heat insulation to the pipe connecting Tightening torque (N•m) 2. -
Page 17: Others
Installation Manual Others Optional wired remote controller wiring Strip off approx. 9 mm the wire to be connected. External static pressure settings To separate using of remote control for each indoor unit Wiring diagram in case of 2 air conditioners are installed near. Change the external static pressure setting with the DIP Remote Control B Setup. -
Page 18: Auto Restart Setting
– 17 – Installation Manual Auto Restart Setting This product is designed so that, after a power failure, it can restart automatically in the same operating mode as before the power failure. Information The product was shipped with Auto Restart function in the off position. - Page 19 EG55760001-00...