Advertisement
Advertisement
Table of Contents
Related Manuals for D-Link DSL-6300V
Summary of Contents for D-Link DSL-6300V
- Page 1 DSL-6300V USER MANUAL FEBRUARY 2011 ISSUE 1...
- Page 2 All other trademarks are the property of their respective owners.. The information presented is subject to change without notice. D-Link Corporation assumes no responsibility for inaccuracies contained herein. Copyright © 2011 D-Link Corporation. All Rights Reserved. Conformance statements The device complies with Part 68 of the Federal Communications Commission (FCC) statements and UL.
-
Page 3: Table Of Contents
Contents About this document Purpose ................................. v Reason for revision ............................v Intended audience ............................v Supported systems ............................v Safety information ............................v Conventions used ............................vi Eco-environmental statements ........................vi Technical support ............................vi Installation Guide Install the CPE ............................1-1 Troubleshooting TCP/IP configuration Product conformance... - Page 4 ......................................................................................................Issue 1 February 2011...
-
Page 5: About This Document
Purpose The purpose of the User Manual is to provide installation information, procedures for installation, service activation and system reconfiguration for the DSL-6300V VDSL2 Bridge. Additionally the User Manual contains status indicators and troubleshooting information and a comprehensive description of safety guidelines. -
Page 6: Conventions Used
WARNING: Warns that a failure to take appropriate safety precautions could result in physical injury. In addition it warns of danger of electrical shock. Eco-environmental statements The statements that follow are the eco-environmental statements that apply to DSL-6300V products. Countries, states, localities, or other jurisdictions may require that systems be established for the return and/or collection of packaging waste from the consumer, or other end user, or from the waste stream. -
Page 7: Installation Guide
Install the CPE When to use Use this procedure to install the DSL-6300V and to establish a connection. The following figure shows the CPE with all external connections established. This will be described step by step in the procedure below. -
Page 8: Installation Guide Install The Cpe
Installation Guide Install the CPE .................................................... Figure 1-1 Overview about all external connections System requirements and safety guidelines 1. The CPE should be located in a cool dry place, with at least 5 cm (2 in.) of space on all sides for ventilation. - Page 9 Installation Guide Install the CPE .................................................... Mounting procedure There are two ways for mounting the CPE: Wall mounting • 1. Locate a high position on the wall that is free of obstructions. 2. Connect two screws in the wall 5 cm (2 in.) apart. Do not screw the screws all the way into the wall.
- Page 10 Installation Guide Install the CPE ..............................................................................................Connect one end of the Category 5 UTP network cable to the Ethernet LAN port on the CPE and the other end to the port of the network interface on the appropriate device, for example a PC, Notebook and so on.
-
Page 11: A Troubleshooting
Troubleshooting Overview Purpose This Appendix provides guidance for troubleshooting. The CPE operation can easily be monitored via the LED indicators to identify problems. The table below describes common problems you may encounter and possible solutions. Diagnosing Symptom Possible cause Solution POWER LED Power outlet, power Check the power outlet by plugging in another... - Page 12 Troubleshooting Overview ......................................................................................................A - 2 Issue 1 February 2011...
-
Page 13: Btcp/Ip Configuration
TCP/IP configuration Overview The following procedures provide TCP/IP configuration instructions for all supported operating systems. Windows 7 1. Open Network and Internet from the Control Panel. 2. Open Network and Sharing Center from the Network and Internet. 3. Right-click Local Area Connection from Network and Sharing Center. 4. - Page 14 TCP/IP configuration Overview .................................................... 3. Under the General tab, select Internet Protocol (TCP/IP) , and click Properties . The Internet Protocol (TCP/IP) properties window appears. 4. Select the radio button. Obtain an IP address automatically 5. Select the radio button. Obtain DNS server address automatically 6.
-
Page 15: C Product Conformance
Product conformance Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 16 This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Company: D-Link Corporation Address: 17595 Mt. Herrmann, Fountain Valley, CA, United States, 92708 Tel no.: 714-885-6105...