Connecting To The Heat Source; Installing (Deinstalling) The Controller; Commissioning; Powering Up Easycontrol - Bosch EasyControl CT200 Installation And Operating Instructions Manual
Remotely operated controller
Hide thumbs
Also See for EasyControl CT200:
- Quick install manual (32 pages) ,
- Installation and operating instructions manual (15 pages)
Table of Contents
Advertisement
4.4
Connecting to the heat source
The installation instructions for the heat source contain further
information about the connection of EasyControl.
l ≤ 100 m
Fig. 6
Connecting the EasyControl adaptor
There are various possibilities for connection to a heat source:
• Replacing an existing controller of the 100 to 400 series on the same
wall plate. EasyControl is ready for operation.
• Bosch heat source appliance with a visible orange controller
connection on the underside. Connect the EasyControl at the orange
terminal.
1)
• Bosch
heat source without a visible connection for the controller.
The heat source must be opened by a recognized installer.
• Heat sources, which use iRT, OpenTherm or On-Off, can only be
connected with an EasyControl adaptor (accessory).
See the back of this document for the web address and select
"Is EasyControl suitable for me", or consult a recognized installer.
4.5
Installing (deinstalling) the controller
1.
1.
2.
Fig. 7
Installing (deinstalling) the controller
Installing
▶ Hook the EasyControl behind the wall plate[1].
▶ Press the EasyControl with the underside against the wall plate, until
an audible "click" is heard [2].
The EasyControl is now locked.
1) Or a Bosch Group brand (Nefit, Junkers, Worcester, ELM LeBlanc).
EasyControl – 6720884199 (2018/01)
Deinstalling
▶ Unlock the EasyControl by pressing the unlocking key [3].
▶ Slightly lift the underside of the EasyControl and remove it [4].
5
5.1
▶ Remove the protective film from the EasyControl.
▶ Plug the mains plug of the heat source into the socket.
▶ Switch on the heat source.
This also causes the EasyControl to be supplied with mains voltage, and
it searches for a connection to:
• the heat source [1],
• a Wi-Fi network [2],
l ≤ 3 m
• the Bosch server [3].
0010018152-001
Fig. 8
[1]
[2]
[3]
[4]
[5]
[6]
A green check mark [5] shows, that the connection is made. A red cross
[6] shows, that the connection is not made. See section 8.2, page 9 for
an overview of possible causes and solutions.
5.2
The software version of this document is 01.xx.xx. The installed
software version is shown in the start screen [4]. Software updates are
performed automatically. It is possible that, when delivered, the
EasyControl does not yet have the current software version and does not
therefore support all the functions in the app. The automatic update may
take some time to start. Via the app an update can start immediately.
After an update has been performed, the arrangement of the touch
4.
screen may differ from this document. See the latest version of this
3.
document on the EasyControl site for Bosch.
0010018153-001
5.3
It is possible to change the settings by means of a horizontal or vertical
wiping movement (swipe) or by pressing (tap). Only operate the touch
screen with your hand.
2) See the back of this document for the web address.
Commissioning
Powering up EasyControl
1
2
3
01.00.00
4
Start screen
Connection with the heat source
Connection with Wi-Fi network
Connection with Bosch server
Software version (example)
Connection made (example)
Connection not made (example)
Software update
Operation of the touch screen
Commissioning
5
6
0010018154-001
2)
5
Hide quick links:
Advertisement
Table of Contents
