Advertisement
Quick Links
INSTALLATION AND SETUP GUIDE
5818MN TRANSMITTER
1/2" MAXIMUM
EXTERNAL PHYSICAL BARRIER
(e.g. MOLDING)
Figure 1: Door Installation
GENERAL INFORMATION
The 5818MNL Recessed Door Transmitter is a single-
zone, reed switch magnetic contact sensor that
provides concealed protection for a door. It is intended
for use only with alarm systems that support 5800
series devices.
The transmitter is powered by one AAA Lithium (or
alkaline) battery that is easily replaced when a low
battery condition is indicated by the control panel.
PROGRAMMING
Each 5818MNL has its own unique identification code
(serial
number)
permanently
manufacture.
You must "enroll" the transmitter's serial number in the
control panel before it will operate in the system.
NOTE: During programming of the control panel,
5818MNL transmitters must be enrolled as Input Type
3 (Supervised RF), Loop 1 (mandatory for UL
installations).
INSTALLATION
NOTE: Do not use on metal frame doors.
Mounting
Before selecting the mounting location, please read
the following:
• The preferred direction of mounting is vertical,
although the 5818MNL may be mounted in any
direction
if
satisfactory
transmissions is obtained.
• • • • A physical barrier (e.g., a molding strip on the
door frame) should be present to protect against
defeat of the contact from outside the premises.
• • • • Make sure that no more than 1/2" gap exists
between the faces of the transmitter and magnet
cases when they are installed and set.
• • • • Once installed, an alarm signal must be
obtained before a separation of 2" is reached
as the door is opened.
FRAME OF
DOOR
MAGNET
"IN" SIDE OF
DOOR
1. Select a location for the transmitter on the door
2. Select the location for the magnet on the door,
3. Tape
assigned
during
4. Mark the selected locations.
5. Drill holes at the locations marked. The transmitter
6. Insert the transmitter and magnet cases into
reception
of
its
NOTE: A closure plug is supplied to cover an empty
transmitter hole if it becomes necessary to relocate
the transmitter.
K9485V1 10/05 Rev. E
ADEMCO 5818MNL
Recessed Door Transmitter
TRANSMITTER
CASE
END CAP
PC BOARD
Figure 2: Battery/Transmitter Assembly
frame (never on the hinged edge). CAUTION: Do
not install in the door.
directly opposite the transmitter location.
the
transmitter
and
approximate locations (with battery installed and
unit together as described in the BATTERY
INSTALLATION / REPLACEMENT section below
and conduct Go/No Go tests (refer to control
panel's instructions) to verify adequate signal
strength.
Reorient
or
relocate
necessary.
will require a 3/4" diameter hole in the edge of the
frame, at least 3" deep. The magnet will require a
3/8" diameter hole in the edge of the door at least
1/2" deep.
their respective holes, so that their ends are flush
with the surface.
• DO NOT hammer in place with hard blows. If
necessary, tap gently with a rubber mallet or
wood block.
• The transmitter case may be secured by two #4
flat head, self-tapping screws via the holes in its
mounting flanges, or the flanges can be
snapped off by scoring around them first with a
sharp knife.
• If necessary, either case may be secured with a
suitable adhesive.
ANTENNA
REED
SWITCH
magnet
in
their
transmitter
if
Advertisement
Related Manuals for Honeywell ADEMCO 5818MNL
Summary of Contents for Honeywell ADEMCO 5818MNL
- Page 1 K9485V1 10/05 Rev. E ADEMCO 5818MNL Recessed Door Transmitter INSTALLATION AND SETUP GUIDE 5818MN TRANSMITTER TRANSMITTER CASE FRAME OF DOOR 1/2" MAXIMUM ANTENNA MAGNET REED SWITCH END CAP PC BOARD "IN" SIDE OF DOOR EXTERNAL PHYSICAL BARRIER (e.g. MOLDING) Figure 2: Battery/Transmitter Assembly...
- Page 2 Note: For UL certified installations, this product is Listed for Residential use only. For the latest warranty information, please go to: www.honeywell.com/security/hsc/resources/wa 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright© 2008 Honeywell International Inc. www.honeywell.com/security ÊK9485V1mŠ K9485V1 10/05 Rev. E...