Table of Contents
Advertisement
Quick Links
Transport Frame
TransPro™ 80 Tow-Behind Trailer
Model No. 04238—Serial No. 230000801 and Up
Model No. 04244
Model No. 04245
Model No. 04247
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. The trailer tires should be inflated to 0.35 bar (5 psi); read
the Operator's Manual.
1. Warning—do not carry passengers; do not tow down slopes
greater than 15°; do not exceed 24 km/h (15 mph); drive
in a straight line when moving fast; adjust your speed
according to ground conditions.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
98-8687
106-4669
Register at www.Toro.com.
decal98-8687
decal106-4669
Form No. 3415-600 Rev B
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3415-600* B
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro 04238
Summary of Contents for Toro 04238
- Page 1 Form No. 3415-600 Rev B Transport Frame TransPro™ 80 Tow-Behind Trailer Model No. 04238—Serial No. 230000801 and Up Model No. 04244 Model No. 04245 Model No. 04247 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
-
Page 2: Installation
Installation Mounting the Axle and Ramp (Model 04245) or Rail The Transpro 80 is intended for use with Greensmaster (Models 04244 and 04247) 800, 1000, 1010, 1600, 1610, 2000, 2600, as well as Flex 18, 21, 1800, 1820, 2100, 2120 and eFlex 1800, Assemblies 1820, 2100, 2120 Walk Greensmasters. - Page 3 Mounting the Wheel Assemblies Mount a wheel assembly to each axle hub with 4 lug nuts (Figure 5). Tighten the nuts to 108 N⋅m (80 ft-lbs). Adjust the tire pressure to 5 psi (34 kPa). g014665 Figure 5 g215364 Figure 3 1.
- Page 4 Mounting the Greensmower Using one of the configurations shown in Figure 7 Figure 8, adjust and secure the hitch straps to the Wheel Assemblies trailer tongue. (Models 04244 and 04247 only) Note: On the Greensmaster 1000, 1010, and 2000 when equipped with a groomer, you must remove the wheel shaft on the groomer end and purchase and install a new wheel shaft (Part No.
-
Page 5: Loading The Trailer
(Figure 11). Lower other Toro Greensmowers. Read and follow the the trailer bed to the ground. mounting instructions molded into the sides of the wheels. g014669... - Page 6 • On flat ramps, rotate the wheel rods downward over the greens mower transport wheels (Figure 13). • On rail ramps, lift the wheel rod and rotate it behind the greens mower transport wheels (Figure 14). g014672 Figure 14 1. Wheel rod (shown in the closed position) Push down on the handle until the trailer g214902 assembly locks into the latch assembly...
-
Page 7: Operation
Replace any parts removed during servicing or adjustments. 1. Bungee strap To ensure optimum performance and continued safety of this product, always use genuine Toro The Transpro 80 adds extra towing weight to the replacement parts. Replacement parts and vehicle. Drive the vehicle safely. -
Page 8: Recommended Maintenance Schedule(S)
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the torque of the wheel lug nuts. After the first 10 hours • Service the wheel hub and inspect for damage. Yearly • Lubricate the wheel hub assembly. Servicing the Wheel Hub Lubricating the Wheel Hub Assembly Service Interval: Yearly... -
Page 9: Checking The Torque Of The Wheel Lug Nuts
Checking the Torque of the Wheel Lug Nuts Service Interval: After the first 10 hours Check the torque of the wheel lug nuts each time you install the wheels and after the first 10 hours of operation. WARNING Failure to maintain proper torque could result in failure or loss of wheel and could result in personal injury. - Page 10 Notes:...
- Page 11 Notes:...