hit counter script
Yaesu ZCUT-9GR Instruction Manual
  1. Manuals
  2. Brands
  3. Yaesu Manuals
  4. Dispenser
  5. ZCUT-9GR
  6. Instruction manual

Yaesu ZCUT-9GR Instruction Manual

Auto tape dispenser
Hide thumbs

Advertisement

Table of Contents

AUTO TAPE DISPENSER
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Yaesu ZCUT-9GR

Summary of Contents for Yaesu ZCUT-9GR

  • Page 1 AUTO TAPE DISPENSER INSTRUCTION MANUAL...

  • Page 2: Read Before Use

    Read Before Use Thank you very much for buying our tape dispenser ZCUT-9GR. Most of the function is the same as ZCUT-9, but some of additional function such as Removable Roller Unit and Programing Function becomes more convenient. Please read this Instruction Manual carefully.

  • Page 3: Safety Instructions

    Safety Instructions The safety guidelines in this Instruction Manual must be observed in order to prevent damage to the machine or injury to the operator or other persons. The safety guidelines presciribed "Warning " and "Caution" describe possible injury or damage that may be suffered from operating or maintaining the machine in a manner other than as described in this Instruction Manual.
  • Page 4 Warning Do not plug in, unplug the cord, or operate the machine with wet hands. Failure to observe this may result in injury due to electric shock. Never insert your finger, or any other body part, or any foreign object into the machine. Failure to observe this may result in injury.

  • Page 5: Identification Of Parts

    Identification Of Parts CONTROL PANEL LED LAMP START BUTTON AUTO / MANUAL MODE REV BUTTON BUTTON DISPLAY SELECT BUTTON ＋BUTTON FWD BUTTON －BUTTON CONTROL PANEL UPPER CASE TAPE HOLDER P.C.B.(A) ROLLER UNIT SENSOR BLADE UNIT TAPE HOLDER ADJUST LEVER FLEXIBLE TAPE SUPPORT...

  • Page 6: Release Button

    Identification Of Parts HOLD DOWN ROLLER UNIT ROLLER LOCK LEVER TAPE FEED ROLLER TAPE INLET TAPE HOLDER AC CORD INLET HOLD DOWN ROLLER RELEASE BUTTON LOWER TAPE HOLDER POWER SWITCH BOTTOM OF BODY ASSIST STAND SPARE FUSE FUSE BLADE UNIT RELEASE LEVER FUSE HOLDER SEPARATOR...
  • Page 7 HOLD DOWN ROLLER UNIT. ◆Press the START BUTTON. Remove the first piece of tape and discard it. Now your ZCUT-9GR is ready to use. Always use Tweezers to remove tape. Whenever set the tape, make sure that adhesive side of tape is always faced down.

  • Page 8: Mode Setting

    Set the Tape Length ◆Make sure that DISPLAY indicating <cutting length>. INDICATE CUTTING LENGTH The cutting length is always indicates in some alphabets like A,b,C,d,E,F. ◆Set the cutting length. Set your needed length by using +/- BUTTON. A～F The cutting length is adjustable in between 5 mm to 999 mm. Can set six different length by using SELECT BUTTON.
  • Page 9 P-MODE (Preset Mode) P-MODE The machine is able to be programmed. INDICATE CUTTING LENGTH A signal will be shown based on your selected quantity of pieces and it will all cut out. (Maximum 999 pieces.) A buzzer will has sound when the program is finished. You can use the mode either MANUAL or AUTO.
  • Page 10 Programing Function Function that cuts the material registered from A to F accordingly. Set a cutting length As refer to the following figure, operation will keep working. This function may apply every mode. ◆Please follow the instruction on page 7. ◆Set the cutting length from A to F as you prefer.

  • Page 11: Other Functions

    How to Manage a Curling Tape ◆Press the HOLD DOWN ROLLER RELEASE BUTTON in order to open the HOLD DOWN ROLLER UNIT. ◆Extend the ROLLER LOCK LEVER so that the roller will not turn. ◆Close the HOLD DOWN ROLLER UNIT. With the rollers locked, the tension may cause the length to vary.

  • Page 12: Maintenance

    Replace the Blade Unit REMOVE BLADE UNIT Only Blade is not accepted to be replaced. It needs to change with the whole Blade Unit. ◆Turn the POWER SWITCH off. ◆Remove the BLADE UNIT by releasing the BLADE UNIT RELEASE LEVER. ◆Install the new BLADE UNIT into the body.

  • Page 13: Error Messages

    Roller Unit When waste of tape glue is found, please refer to page 14 and follow the procedure for cleaning ROLLER UNIT. Clean the Body Put neutral detergent on a damp cloth to clean the body. Do not use alcohol or solvent to clean the plastic parts. Error Messages The buzzer will has a sound then a message will flash and show on the DISPLAY.

  • Page 14: Roller Unit

    ROLLER UNIT When tape jammed, you can remove ROLLER UNIT wihtout using any tools and make sure about the status of Roller Unit. Machine can be stable due to easy cleaning and removal of tape waste. ◆Please switch off and remove power cord from machine. ◆Remove BLADE UNIT.

  • Page 15: Troubleshooting

    Trouble Shooting Before returning the machine for repairing, please check the followings. The POWER SWITCH is The AC CORD is loosen. Check the AC CORD then plug in the outlet firmly. on but the machine can The FUSE has been blown. Replace the FUSE.

  • Page 16: Warranty

    ◆Was not modified or damaged by tempering, user error, accident, disaster, abuse, misuse, power supply, power application, alternation, repair, modification, a fix or replacement by someone other than the original product. YAESU KEIKOGYO CO., LTD. 39-8, Senju Motomachi, Adachi-Ku, Tokyo, 120-0041, Japan Phone...

Table of Contents