Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yaesu FD-160 III
Summary of Contents for Yaesu FD-160 III
- Page 1 AUTO FILM DISPENSER FD-160 Ⅲ FD-200 Ⅲ FD-300 INSTRUCTION MANUAL...
-
Page 2: Please Read Before Use
Please Read Before Use Thank you very much for purchasing our film dispenser FD series. Most of the function is same as conventional models, but some of additional function are available and durability is improved. Most of operation is same for FD-160Ⅲ, FD-200Ⅲ and FD-300. Some of different operations are described separately. -
Page 3: Safety Instructions
Safety Instructions The safety guidelines in this Instruction Manual must be observed in order to prevent damage to the machine or injury to the operator or other persons. The safety guidelines presciribed "Warning " and "Caution" describe possible injury or damage that may be suffered from operating or maintaining the machine in a manner other than as described in this Instruction Manual. - Page 4 Warning Do not plug in, unplug the cord, or operate the machine with wet hands. Failure to observe this may result in injury due to electric shock. Never insert your finger, or any other body part, or any foreign object into the machine.
- Page 5 Caution Do not insert any foreign material from the film outlet. This can cause failure of the machine. An operator’s presence is required whenever the machine is in operation. Turn the machine off and unplug the cord when the operator is not present. Failure to observe this can result in injury.
-
Page 6: Identification Of Parts
Identification of Parts It might cause an injury. Caution: Whenever you clean the BLADE, do not touch the sharp edge of Cutting edge the BLADE. FEEDING ROLLER CUTTER BLADE FILM GUIDE CARRYING HANDLE CASE SAFETY SWITCH FRONT PANEL HOOK SUPPORTING ROLLER (UPPER) FRONT PANEL SUPPORTING ROLLER... - Page 7 Identification of Parts SAFETY COVER HOOK GUIDE ROLLER SAFETY COVER （FD-160Ⅲ） GUIDE STEP (LEFT/RIGHT) （FD-160Ⅲ） BIBBIN SHAFT SOCKET BRAKE ROLLER （FD-160Ⅲ） FILM HOLDER （FD-160Ⅲ） BOBBIN SHAFT SOCKET TAPER ROLLER （FD-160Ⅲ） ADJUST DIAL （FD-160Ⅲ） TORQUE LIMITER POWER SWITCH （FD-160Ⅲ） AC CORD INLET AC CORD INLET POWER SWITCH SPARE FUSE...
-
Page 8: Load The Film
Load the Film ■The SOCKET-OUTLET shall be installed near the equipment and shall be AC CORD INLET easily accessible. ■Set the machine only in the upright position. ■Plug in AC CORD to the AC CORD INLET. ■Make sure the POWER SWITCH is off then plug into an appropriate grounded AC outlet. - Page 9 Load the Film ☆ If you fail to set the film by the instruction on Page 8, try following method. ■Lift the SAFETY COVER HOOK and open the SAFETY COVER. ■Insert the film between FEEDING ROLLER and SUPPORTING ROLLER. Then press FWD BUTTON to load the film.
-
Page 10: Setting The Mode
Set the Film Length ■Make sure that cutting length is displayed. INDICATE CUTTING LENGTH ・ The cutting length will be displayed as A, b, C, d, E, F with 3 digits, or 4 digit number. ・ If cutting length is not displayed, press SELECT BUTTON more than few (exp. - Page 11 P-MODE (Preset Mode) P-MODE CONFIRM THE CUTTING LENGTH A buzzer will sound when the number of setting pieces is completed. You can use the mode either MANUAL or AUTO. This setting is 999 pcs maximum. SELECT (exp. A-100mm) ■Press SELECT BUTTON and select the cutting length from A to F and 4 digits number.
-
Page 12: Memo Function
Memo Function Present cutting quantity can be memorized. PRESS LONGER ■Press AUTO/MANUAL BUTTON longer and display present cutting quantity. ■Press ＋ BUTTON. ・ Present cutting quantity will be forwarded and memorized. ・ The data transferred is not deleted even if switching off. ■If pressing AUTO/MANUAL BUTTON longer, display the cutting length. -
Page 13: Feeding Roller
Set the bobbin (FD-200Ⅲ, FD-300) Peel the film and set it on ROLLED FILM FEEDING ROLLER. ① ② BOBBIN ① Grip BOBBIN to insert ROLLED FILM. ② Insert the ROLL to BOBBIN. ・ Set the ROLL at the center of BOBBIN. ③ Insert PINS at BOBBIN SHAFT SOCKET. -
Page 14: Troubleshooting
Trouble Shooting < Error Messages > In the case of buzzer sound during the operation, the following massage may display E-02 BLADE IS OUT OF POSITION POWER SWITCH is off A signal shows that the blade is not installed correctly or the film is jammed. ・... -
Page 15: Warranty
Warranty We warrant to the original purchaser of the product that will be free form defects in material or workmanship for as long as the original purchaser owns the product, when given normal wear and proper usage. The limited warranty for the machine shall be for a period of 180 days form the date of purchase. - Page 16 YAESU KEIKOGYO CO., LTD. 39-8, Senju Motomachi, Adachi-Ku, Tokyo, 120-0041, Japan Phone 81-3-3888-8751 Fax 81-3-3888-1592 PLEASE VISIT OUR WEB SITE URL:www.yaesu1965.com 19G24...