Honeywell PRO-2200 Installation Manual page 2
Single reader enclosure
Hide thumbs
Also See for PRO-2200:
- Installation manual (20 pages) ,
- Installation manual (15 pages) ,
- Installation manual (16 pages)
Advertisement
Small PRO-2200 Enclosure - PRO22ENC4
NOTICE
Any use of this product is subject to the terms and acceptance of the Engineered Systems Software Agreement. Please request a copy from
Engineered Systems, and review the agreement carefully.
DISCLAIMER
PRODUCT LIABILITY; MUTUAL INDEMNIFICATION
In the event that a Customer receives a claim that a Product or any component thereof has caused personal injury or damage to property of
others, Customer shall immediately notify Engineered Systems in writing of all such claims. Engineered Systems shall defend or settle such
claims and shall indemnify and hold Customer harmless for any costs or damages including reasonable attorneys' fees which Customer may be
required to pay as a result of the defective Product or the negligence of Engineered Systems, its agents, or its employees.
Customer shall hold harmless and indemnify Engineered Systems from and against all claims, demands, losses and liability arising out of dam-
age to property or injury to persons occasioned by or in connection with the acts or omissions of Customer and its agents and employees, and
from and against all claims, demands, losses and liability for costs of fees, including reasonable attorneys' fees, in connection therewith.
UNPACKING PROCEDURE
CAUTION
If any damage to the shipment is noticed before unpacking, a claim must be filed with the commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to the contents.
The following steps are used to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the container and all packing materials. They may be used again
for reshipment of the equipment, if needed.
2. Inspect the contents for shortage. If items are missing, contact the order entry department at 800-323-4576.
3. Visually check contents. If damage is discovered, perform the following:
• If shipping caused damage to the unit, a claim must be filed with the commercial carrier.
• If any other defect is apparent, call 800-323-4576 for a return authorization.
SHIPPING INSTRUCTIONS
To ship equipment back to Engineered Systems:
1. Contact the customer service department at 800-323-4576 before returning equipment. When calling, please have available:
• A description of the problem or reason for returning the equipment.
• Original purchase order number, invoice number and whether or not the unit is still under warranty.
• A new purchase order number if the unit is not under warranty.
2. Obtain the Return Authorization Number (RMA) from the customer service department at 800-323-4576.
3. Show the RMA number on all packages shipped. Packages not marked with an RMA number will be refused at the factory and returned
COD.
4. Carefully pack the equipment for shipment. Use the original packing material whenever possible.
LIMITED WARRANTY
All Products sold or licensed by Engineered Systems include a warranty registration card which must be completed and returned to Engineered
Systems by or on behalf of the end user in order for Engineered Systems to provide warranty service, repair, credit or exchange. All warranty
work shall be handled through the Customer which shall notify Engineered Systems and apply for a Return Merchandise Authorization (RMA)
number prior to returning any Product for service, repair, credit or exchange. Engineered Systems warrants that its Products shall be free from
defects in materials and workmanship for a period of two years from date of shipment of the Product to Customer. The warranty on Terminals,
Printers, Communications Products and Upgrade kits is 90 days from date of shipment. Satisfaction of this warranty shall be limited to repair or
replacement of Products which are defective or defective under normal use. Engineered Systems' warranty shall not extend to any product
which, upon examination, is determined to be defective as a result of misuse, improper storage, incorrect installation, operation or maintenance,
alteration, modification, accident or unusual deterioration of the Product due to physical environments in excess of the limits set forth in Product
manuals. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THIS PROVISION. THIS WARRANTY IS IN LIEU OF ALL OTHER WAR-
RANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. NO REPRESENTATION OR WARRANTY OF THE DISTRIBUTOR SHALL EXTEND THE LIABILITY OR
RESPONSIBILITY OF THE MANUFACTURER BEYOND THE TERMS OF THIS PROVISION. IN NO EVENT SHALL ENGINEERED SYSTEMS
BE LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS, LOSS OF USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES TO ANY PERSON RESULTING FROM THE USE OF ENGINEERED SYSTEMS' PRODUCTS.
CONFIDENTIALITY
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other materials furnished by Engineered Systems relating to the
design, use and service of the Products shall remain confidential and shall constitute proprietary rights of Engineered Systems and Customer
agrees to treat such information as confidential. Customer shall acquire no rights in the design of the Products or the related materials except to
use such information solely for the purpose of and only during the time it sells the Products. Customer shall not copy the design of any of the
Products or use or cause to be used any Product design or related materials for its own benefit or for the benefit of any other party. The covenants
contained in this section shall remain effective throughout the term of this Agreement and thereafter unless specifically waived by Engineered
Systems in writing.
Installation Guide
2
Small PRO-2200 Enclosure - PRO22ENC4
DIMENSIONS
Height: 8.375" (21.275cm) Width:
7.625" (19.4cm)
Depth: 7.625" (19.4cm)
Metal thickness: .05" (.127cm)
Installation holes: Single ended hanging slots for mounting the cabinet in the
upright position. The 3 hangers are in a triangular pattern. The top two are
located .75" (1.9cm) from the top and spaced 6.125" (15.5cm) apart. The lower
hanger is located .930" (2.36cm) from the bottom and 7.85" (19.9cm) from
each edge. See Enclosure Drawing.
Dual Conduit Knockouts:
½" & 1" (1.27cm x 2.54cm)
Top Side:
1
Bottom Side:
0
Right Side:
1
Left Side:
2
Rear Side:
1
POWER SUPPLY
DO NOT USE POWER SUPPLY TO POWER LOCKS.
PRO22E4PS:12 VDC 1.2 amp continuos power limited output with backup
battery charging. 16.5 VAC 20va wall transformer provided.
Requires 115 VAC/60hz, Maximum battery charge current .5amp
AC on LED
Short circuit and thermal overload protection
All power connection should be made with 18ga or larger wiring
LED DIAGNOSTICS
AC LED
DC LED
ON
ON
Normal operating conditions
OFF
ON
Loss of AC, standby battery supplying power
ON
OFF
No DC output
OFF
OFF
Loss of AC, Discharged or no Stand-by battery.
No DC output.
BACKUP POWER SUPPLY
Automatic Switch over to stand-by battery when AC fails (zero voltage drop)
4.0 AH sealed rechargeable battery
Backup time: 2.5 to 4 hour depending on configuration
CABLES SUPPLIED
Power On Light assembly
Tamper Switch assembly
MAINTENANCE
Replace the 12V 4AH battery every 2 to 2.5 years
Oil the hinges on the door every 12 months
OPERATING PARAMETERS
Temperature: 35 to 110 C (2 to 43 C)
Operating Humidity: Up to 85% non-condensing
Installation Guide
INSTALLATION INSTRUCTIONS
Color: Grey
1.
Remove the 16.5V 20VA wall transformer, battery and parts bag from the
enclosure.
2.
Add all eight plastic standoffs into the mounting holes forming an upper and
lower square.
3.
Measure and install the top two mounting screws with heads smaller than .4"
using proper mounting techniques for the material being used to hold the
PRO22ENC4. Space the screws 6 1/8" apart. Leave the screws exposed
approximately 1/2".
4.
Open the door of the enclosure and place the hanging slots over the mounting
screws. Push the enclosure over the mounting screws and allow the screws to
slide into the slots. Finish tightening the mounting screws to securely hold the
enclosure. Screw in the lower hanger to secure the enclosure against the wall.
5.
Install the tamper switch cable to the bottom two screws on the tamper switch.
Slide the tamper switch holder onto the upper right corner of the enclosure.
Push the tamper switch cable and the tamper switch through the center hole of
the tamper switch holder.
6.
Mount the Power on Light assembly to the enclosure by passing the wire ends
from the outside to the inside of the enclosure through the ¼" hole located on
the upper right side of the enclosure. Secure the Power on Light by sliding the
retaining ring over the wires and onto the light holding it snug to the wall of the
enclosure.
7.
Run all appropriate wiring to the case. Mark each wire as to the panel, location
and input type. All cable shields should tie to the grounding stud found on the
upper left side of the enclosure.
8.
Install the single reader panel onto the 4 standoffs in the bottom left of the
enclosure, placing the power and communications to the top.
9.
Wire the readers, input and output connections by removing the terminals for
ease of wiring. Wire according to installation guide supplied with the single
reader panel.
10. CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSURE
AND PANELS.
11. Mount the PRO22E4PS power supply to the 4 standoffs at the upper right of the
enclosure. Place the terminal strip to the right. Connect the two supplied battery
cables: RED to Batt+, BLACK to Batt-. Wire the PRO22E4PS power supply
through the wall transformer provided. Connect to the AC terminals. Wire the
Power on Light to the AC in connections on the power supply. Plug in the Wall
transformer. The Power on Light should light. Check the voltage at ±DC. The
voltage should be approximately 13.8 VDC.
12. Disconnect the power.
13. Connect the DC power to the panel. Insure that the connection has the correct
polarity. Follow the wiring diagram supplied with the panels.
14. Connect the Tamper Switch cable to the two pin connector "9" located on the
mid right of the panel. See individual panel wiring diagrams supplied with the
panel.
15. Connect Communications wiring per the wiring diagram supplied with the panel.
16. Place the 12V 4AH battery in the cabinet on the bottom right hand side. Attach
the red battery charging connection to the positive terminal of the battery and
the black battery charging connection to the negative connection of the battery.
17. CHECK ALL CONNECTIONS PRIOR TO POWERING UP THE ENCLOSURE
AND PANELS.
3
Advertisement
