Advertisement
Quick Links
32RD Mid-Size Rear-Discharge Deck
Model No. 02710—Serial No. 316000001 and Up
Model No. 02711—Serial No. 316000001 and Up
Model No. 02712—Serial No. 316000001 and Up
These instructions are for a dealer to install a cutting
deck (Models 02710, 02711, or 02712) to a Mid-Size
Power Unit (Models 30069 and 31914).
WARNING
Performing maintenance while the engine is
running can expose your hands, other parts
of your body, and clothing to get caught in
moving parts, causing serious injury.
If you must perform any maintenance while
the engine is running, keep your hands, feet,
clothing, and parts of your body away from
the cutting unit and moving parts.
WARNING
Engine exhaust contains carbon monoxide,
which is an odorless, deadly poison that can
kill you.
Do not run engine indoors or in an enclosed
area.
Important:
Read and understand these assembly
instructions before proceeding. Refer to the Parts
Catalog and Operator's Manual for the machine to
determine which of these parts are to be fitted.
Important:
Ensure that all lifting equipment is
in good condition and has a safe and adequate
capacity. Always seek assistance when lifting
awkward or heavy loads.
Important:
Torque all fasteners to the specified
torque settings. The parts being fitted must not be
drilled, cut or altered in any way.
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
These instructions are for dealers only.
Register at www.Toro.com.
1
Preparing the Machine
No Parts Required
Procedure
1.
Park the machine on a level surface and engage
the parking brake.
2.
Shut off the engine, remove the key, and wait
for the engine to cool.
3.
Raise and support the traction unit.
4.
Remove the 4 lug nuts securing both wheels to
the traction unit
(Figure
Left side shown
Original Instructions (EN)
All Rights Reserved *3405-967* B
Form No. 3405-967 Rev B
Setup Instructions
1).
Figure 1
g237244
Advertisement
Related Manuals for Toro 02710
Summary of Contents for Toro 02710
- Page 1 Model No. 02712—Serial No. 316000001 and Up Setup Instructions These instructions are for dealers only. These instructions are for a dealer to install a cutting deck (Models 02710, 02711, or 02712) to a Mid-Size Power Unit (Models 30069 and 31914). WARNING Preparing the Machine...
- Page 2 Remove the wheels (Figure Remove the deck cover and the PTO engagement linkage rod before lifting and moving the rotary cutting deck into position Installing the Cutting Deck against the power unit (Figure Parts needed for this procedure: Bolt (3/8 x 1 inch) Curved washer Flange nut (3/8 inch) Procedure...
- Page 3 Installing the Guards Parts needed for this procedure: Center discharge guard Bolt (M8 x 25 mm) Washer (M8–17) Locknut (M8) g237288 Figure 4 Drive pulley guard 1. Bell-crank yoke 2. PTO engagement linkage Carriage bolt (M10 x 25 mm) Heavy washer (M10) Adjust the PTO engagement as directed in the Spring washer (M10) Adjusting the Mower Belt Tension section in the...
-
Page 4: Completing The Installation
Install the guard to the traction unit using 2 bolts (M8 x 25 mm), 4 washers (M8–17), and 2 locknuts (M8) in the lower hole on the engine frame (Figure Secure the front of the guard to the deck using the center bolt, washer, and nut you removed previously (Figure Refer to the Adjusting the Height of Cut section... -
Page 5: Setting The Idle Speed
2,900 rpm when the power unit is connected to Models 02710 and 02711 and 3500 rpm when the power unit is connected to model 02712. 2900/3500 rpm is the unloaded engine rpm, adjusted with the PTO off (disengaged). - Page 6 Notes:...
- Page 7 Notes:...