Table of Contents
Advertisement
Switch with Only Active Supervisor Module
2019 Jun 25 15:15:52 switch %PLATFORM-5-MOD_STATUS: Module 5 current-status is
MOD_STATUS_CONFIGPOWERED_DOWN
2019 Jun 25 15:15:53 switch %PLATFORM-5-MOD_STATUS: Module 5 current-status is MOD_STATUS_POWERED_DOWN
The old active Supervisor-1 Module will be powered down. The supervisor Status LED will be blinking
Note
red, when the supervisor module is powered down by the migration command. If the Status LED is not
blinking red, then check the migration status using the show logging onboard migration status command
on any management session.
Step 10
After the successful completion of the system switchover, the following syslog message is displayed:
2019 Jun 25 15:16:39 switch %BOOTVAR-2-SUP_MIGRATION_CONFIG_COMPLETE: Migration process is complete
now. Supervisor-3 (DS-X97-SF1-K9) in standby slot can now be replaced with Supervisor-4
(DS-X97-SF4-K9).
2019 Jun 25 15:18:00 switch %SYSMGR-2-SBY_SUP_LESS_MEMORY_SLOT: Supervisor in slot 6 is running
with less memory than active supervisor in slot 5
2019 Jun 25 15:18:00 switch %SYSMGR-2-CONVERT_STARTUP_ABORTED: Conversion of startup-config failed.
2019 Jun 25 15:18:00 switch %PLATFORM-2-MOD_PWRDN: Module 6 powered down (Serial number JAE17440HVB)
2019 Jun 25 15:18:00 switch %PLATFORM-5-MOD_STATUS: Module 6 current-status is
MOD_STATUS_CONFIGPOWERED_DOWN
2019 Jun 25 15:18:00 switch %PLATFORM-5-MOD_STATUS: Module 6 current-status is MOD_STATUS_POWERED_DOWN
2019 Jun 25 15:18:00 switch %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAE17440HVB)
Warning
A mix of different Supervisor-4 Modules and Supervisor-1/Supervisor-1E Modules outside a maintenance
window is not supported. This mix of modules is supported only while you are migrating from a
Supervisor-1/Supervisor-1E Module to a Supervisor-4 Module. If there is mix of Supervisor-1 and
Supervisor-4 module, the chassis will power down the standby supervisor module, and the first supervisor
module that comes up will become the active supervisor.
Step 11
(Optional) The system will automatically start the boot parameter setup for the supervisor migration process. Do not
set any configuration parameters until the boot parameters are set. After the boot parameters are set, the migration
process is completed for the first supervisor module. Use the show boot command to verify the current boot variables
and the show module command to display the modules installed in the switch.
Supervisor-4 Module outputs
switch# show boot
kickstart variable = bootflash:/m9700-sf4ek9-kickstart-mz.8.4.1.bin
system variable = bootflash:/m9700-sf4ek9-mz.8.4.1.bin
Boot POAP Disabled
switch# show module
Mod
Ports
---
-----
1
48
2
48
3
48
4
48
5
0
6
0
7
48
8
48
10
34
Mod
Power-Status
---
------------
6
powered-dn
ive
Cisco MDS 9700 Series Switches Hardware Installation Guide
136
Module-Type
----------------------------------- ------------------ ----------
4/8/16/32 Gbps Advanced FC Module
4/8/16/32 Gbps Advanced FC Module
2/4/8/10/16 Gbps Advanced FC Module DS-X9448-768K9
4/8/16/32 Gbps Advanced FC Module
Supervisor Module-3
Supervisor Module-4
2/4/8/10/16 Gbps Advanced FC Module DS-X9448-768K9
1/10 Gbps Ethernet Module
1/10/40G IPS,2/4/8/10/16G FC Module DS-X9334-K9
Reason
---------------------------
Policy trigger initiated reset: Stdby has lower mem than act
Installing, Removing, and Verifying Field Replaceable Units
Model
Status
DS-X9648-1536K9
ok
DS-X9648-1536K9
ok
ok
DS-X9648-1536K9
ok
DS-X97-SF1-K9
powered-dn
DS-X97-SF4-K9
active *
ok
DS-X9848-480K9
ok
ok
Advertisement
Table of Contents
Troubleshooting
