Page 1
ST-SV7 SERVICE MANUAL E Model Ver 1.0 2001.06 ST-SV7 is the tuner section in MHC-SV7AV. SPECIFICATIONS Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range 87.5 – 108.0 MHz Antenna FM lead antenna Antenna terminals 75 ohm unbalanced Intermediate frequency 10.7 MHz...
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
ST-SV7 SECTION 2 This section is extracted from instruction manual. GENERAL LOCATION OF CONTROLS – Front Panel – qlw; wa ws CLOCK/TIMER wh (13, 25, 34) DISPLAY qk (13, 18, 33, 40) ENTER ws (22) IR receptor wj PRESET –/+ wd (22) —...
ST-SV7 Setting the time Remote Control Turn on the system. 1 2 3 4 5 Press CLOCK/TIMER (or CLOCK/TIMER SET on the remote). When you set the time for the first time, proceed to step 5. Press O or o repeatedly to select “CLOCK SET”.
SECTION 4 TEST MODE [GC Test Mode] Note: Use following buttons in the test mode. no mark : Button of tuner unit (ST-SV7) Enter the GC Test Mode mode : Button of amplifier unit (TA-SV7AV) Procedure 1: : Button of CD unit (MCE-SV7) 1.
ST-SV7 SECTION 5 DIAGRAMS 5-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
ST-SV7 5-10. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC501 M30622MGA-A69FP (SYSTEM CONTROLLER) Pin No. Pin Name Description Pin No. Pin Name Description AMP-DATA Serial data output to the M61512FP (IC607) — Ground terminal AMP-CLK Serial data transfer clock signal output to the M61512FP (IC607) 65 to 70 —...
Page 21
ST-SV7 • DSP BOARD IC601 CXD9617R (AUDIO DIGITAL SIGNAL PROCESSOR) Pin No. Pin Name Description — Ground terminal XRST Reset signal input from the M61512FP (IC607) “L”: reset EXTIN Master clock signal input terminal Not used (fixed at “L”) Sampling frequency selection signal input terminal Not used (fixed at “L”) VDDI —...
Page 22
ST-SV7 Pin No. Pin Name Description — Ground terminal WMD0 S-RAM wait mode setting terminal Fixed at “L” in this set PAGE2 Page selection signal output terminal Not used (open) — Ground terminal PAGE1, PAGE0 52, 53 Page selection signal output terminal Not used (open) BOOT Boot mode control signal output terminal Not used (fixed at “L”)
Page 23
ST-SV7 • DSP BOARD IC604 LC89056W-E (DIGITAL AUDIO INTERFACE RECEIVER) Pin No. Pin Name Description DISEL Selection terminal of data input terminal Fixed at “L” in this set DOUT Digital data output to the optical transceiver (IC609) DIN0 Digital data input from the optical receiver (IC952) (for MCE-SV7)
Page 24
ST-SV7 • DSP BOARD IC605 AK4527 (A/D, D/A CONVERTER) Pin No. Pin Name Description Audio serial data source selection signal input terminal SDOS “L”: internal ADC output, “H”: DAUX input (fixed at “L” in this set) Serial control mode selection signal input terminal “L”: 3-wire serial, “H”: I2C bus SMUTE Soft muting on/off signal input from the system controller (IC501) “L”: muting on...
Page 25
ST-SV7 • PANEL BOARD IC601 MB90M407PF-G-102-BND (DISPLAY CONTROLLER) Pin No. Pin Name Description 1 to 6 G6 to G1 Grid drive signal output to the fluorescent indicator tube (FL601) 7 to 10 A1 to A4 Segment drive signal output to the fluorescent indicator tube (FL601) VSS FOR IO —...
ST-SV7 SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they may have some difference from the original are seldom required for routine service. Some one. delay should be anticipated when ordering •...
ST-SV7 SECTION 7 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Page 36
ST-SV7 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...