Page 1
SN23HI00MG Dishwasher EN Information for Use Register your appliance on My Siemens and discover exclusive services and offers. Siemens Home Appliances...
en Safety 1 Safety Observe the following safety instructions. 1.1 General information Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe ¡ for future reference or for the next owner. Do not connect the appliance if it has been damaged in transit. ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. Connect and operate the appliance only in accordance with the ▶ specifications on the rating plate. Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- ▶...
en Safety WARNING ‒ Risk of burns! If the appliance is not installed properly, this may result in burns. With free-standing appliances, ensure that they are installed with ▶ the back panel against a wall. 1.5 Safe use WARNING ‒ Risk of serious harm to health! Failure to comply with safety instructions and directions for use on packagings of detergent and rinse aid products may cause seri- ous harm to health.
Safety en WARNING ‒ Risk of scalding! If you open the appliance door while the programme is running, hot water may splash out of the appliance. Open the appliance door carefully if the programme is still run- ▶ ning. WARNING ‒ Risk of tipping! Overfilling the Baskets may cause the appliance to tip up. Never overfill the Baskets with free-standing appliances.
en Safety Only use genuine spare parts when repairing the appliance. ▶ If the power cord or the appliance power cable of this appliance ▶ is damaged, it must be replaced with a special power cord or special appliance power cable, which is available from the man- ufacturer or its Customer Service.
Page 9
Safety en Keep children away from the appliance when open. The water in ▶ the interior of the dishwasher is not drinking water. It may con- tain residues of detergents and rinse aid. WARNING ‒ Risk of injury! Children may get their fingers caught in the slots of the tablet col- lecting tray and injure themselves.
en Preventing material damage Modified or damaged water hoses Preventing material damage 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing material damage 2.1 Safe installation Only use the water hoses supplied ▶...
Environmental protection and saving energy en So as not to scratch the finish on ▶ Installation and connection 4 Installation and con- the appliance, do not use sponges with a rough surface or abrasive nection cleaning agents. To prevent corrosion, do not use To ensure proper operation, connect Installation and connection ▶...
en Installation and connection installing it under a continuous work- 4.4 Drinking water connec- top that is securely connected to ad- tion jacent cabinets. Follow the safety instructions. Connect your appliance to a drinking → Page 4 water connection. Follow the instructions for electrical Installing the drinking water connection.
Familiarising yourself with your appliance en Familiarising yourself with your appliance 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 52.
Page 14
en Familiarising yourself with your appliance Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 29 Bottom basket Bottom basket → Page 23 Dispenser for special salt Add special salt to the dispenser for spe- cial salt. → "Water softening system", Page 25 Lower spray arm The lower spray arm washes the table- ware in the bottom basket.
Familiarising yourself with your appliance en 5.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. 3 4 5 6 ON/OFF button and reset Switching on the appliance button...
en Familiarising yourself with your appliance Programme buttons and addi- Programmes tional functions → "Programmes", Page 18 Additional functions → "Additional functions", Page 21 Start button Starting the programme → Page 35 button If you press for approx. 3 seconds, you can open the basic set- tings. → "Changing basic settings", Page 37 Remote Start...
Page 17
Familiarising yourself with your appliance en Symbol Description If you have started a pro- gramme, the symbol lights up on the display. If you have activated the button lock, the symbol lights up on the display. → "Activating button lock", Page 35 If the water inflow or drainage malfunctions, the symbol lights up or flashes on the display.
Page 18
en Programmes Programmes 6 Programmes You can find an overview of the pro- ted. The running time will change if Programmes grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Programmes en Programme Programme se- quence Tableware: Time-optimised: Delicate tableware, cutlery, tem- Cleaning 45 °C ¡ ¡ Speed 45° perature-sensitive plastics and Intermediate rinse ¡ glasses Final rinse 55 °C ¡ Level of soiling: Lightly adhering fresh food rem- ¡ nants Use only if appliance is unloaded. Machine Care 70 °C Machine Care → "Favourite ", Page 19...
Page 20
en Programmes Tip: To reset the programme to the pre-rinse programme stored at the factory, use the Home Connect app or reset your appliance to the factory settings. Depending on the appliance specifications...
Additional functions en Additional functions 7 Additional functions You can find an overview of the additional functions that can be selected here. Additional functions Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme.
en Features Raise or lower the basket evenly to 8.1 Top basket the right level. Arrange cups, glasses and small items of tableware in the top basket. Check that the basket is level on both sides. Release the levers. You can adjust the height of the top The basket clicks into position.
Features en 8.3 Bottom basket 8.4 Folding prongs Arrange pans and plates in the bot- Use the folding prongs to position tom basket. tableware securely, e.g. plates. Large plates up to a diameter of You can fold the prongs down to po- 31 cm can be arranged in the bottom sition pans, bowls and glasses basket as shown.
en Before using for the first time Insert the baking sheet spray head 8.5 Cutlery drawer in the holder and turn to the Arrange cutlery in the cutlery drawer. right . The baking sheet spray head Arrange cutlery with the points and clicks into position.
Water softening system en Tip: You can change these settings Add special salt. → Page 26 and other Basic settings → Page 36 Add rinse aid. → Page 28 at any time. Switch on the appliance. → Page 34 Setting the water softening system. Water softening system 10 Water softening sys- → Page 26 Set the amount of rinse aid to be dispensed.
en Water softening system Special salt for dishwashers can 10.2 Setting the water soften- damage the tub due to corrosion. ing system To make sure that any special salt ▶ that escapes is washed out of the Set the water hardness on your appli- tub, add the special salt to the dis- ance.
Water softening system en 10.4 Switching off the water 10.5 Regeneration of the wa- softening system ter softening system If you find the special salt refill indic- In order to obtain fault-free function of ator irritating, e.g. when using com- the water softening system, the appli- bined detergents with salt replace- ance performs regeneration of the ment substances, you can switch the...
en Rinse aid system Close the lid of the dispenser for Rinse aid system 11 Rinse aid system rinse aid. The lid clicks into position. Rinse aid system 11.1 Rinse aid 11.2 Setting the amount of For optimum drying results, use rinse rinse aid aid.
Detergent en The display shows Hxx. Powder detergent The display shows . Powder detergent is recommended Press repeatedly until for shorter programmes. the display shows the value r05 The dosage can be adjusted to the set at the factory. level of soiling. Press repeatedly until the dis- Liquid detergent...
en Detergent According to the manufacturers, ness, usually 26 °E, without combined detergents generally only adding special salt. For the best function up to a water hardness of washing and drying results we re- 26 °E. With a water hardness above commend using special salt from a 26 °E you will need to add special water hardness of 17 °E.
Page 31
Tableware en Add the detergent to the dry deter- Close the lid of the detergent dis- gent dispenser. penser. 50 ml 25 ml 15 ml If you are using tablets, one is The lid clicks into position. enough. Insert the tablets in a hori- The detergent dispenser will open zontal position.
en Tableware 13.1 Damage to glass and Cause Recommenda- tion tableware Highly caustic al- If you are using Only put glasses and china in the kaline or highly highly caustic al- dishwasher if it is marked as dish- acidic cleaning kaline or highly washer-safe by the manufacturer.
Page 33
Tableware en allowing steam to escape and water To save resources, do not pre- to leak out around the door. This rinse tableware under running wa- could damage your kitchen units. ter. Observe the following when arran- ging tableware: – Put heavily soiled tableware in the bottom basket, e.g.
en Basic operation 13.3 Removing tableware 14.2 Setting a programme To adjust the washing programme to WARNING the soiling level of the tableware, se- Risk of injury! lect a suitable programme. Hot tableware can cause burns to the Requirement: The appliance door is skin. When hot, tableware is sensitive closed.
Basic operation en 14.5 Starting the programme 14.8 Interrupting programme Press Note: When you open the appliance ▶ door once the appliance has heated The programme has ended when up, leave the door slightly ajar for a the display shows "0h:00m". few minutes and then close it. This Notes will help prevent excess pressure If you want to add more tableware...
en Basic settings Basic settings 15 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 15.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H00 - H07...
Basic settings en Basic setting Display text Selection Description Wi-Fi Cn0 - Cn1 Switch the wireless network connection on or off. Level "Cn0" switches the wireless network connection off. This basic setting is not available until you have con- nected the appliance with the Home Connect app.
en Home Connect Press repeatedly until 16.1 Setting up the the display shows the required set- Home Connect app ting. Press repeatedly until the dis- Install the Home Connect app on play shows the right value. your mobile device. Start the Home Connect app and You can change several settings. set up access for Home Connect.
Cleaning and servicing en This initial registration prepares the Activating Remote Start Home Connect functions for use and When you have selected "rc1" in the is only required when you want to basic settings of this function, activ- use the Home Connect functions for ate the function on your appliance.
Dishwasher Care and Ma- ance to malfunction. To avoid such chine Cleaner for Dishwashers online faults and reduce odours, we recom- at https://www.siemens-home.bsh- mend cleaning your appliance at reg- group.com/store or from customer ular intervals. service.
Cleaning and servicing en Make sure that there are no alu- ¡ 17.5 Filter system minium parts, e.g. extractor hood The filter system removes coarse grease filters or aluminium pans, in soiling from the dishwashing cycle. the interior of the appliance. If you have not run Machine Care ¡...
en Cleaning and servicing Pull down the micro filter to re- Insert the filter system into the ap- move. pliance and turn the coarse filter clockwise. Make sure that the arrow mark- ‒ ings match up. Press the locking catches gether and lift the coarse filter out ...
Page 43
Cleaning and servicing en Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code in the table of contents and on our website siemens-home.bsh-group.com. WARNING Risk of electric shock! Incorrect repairs are dangerous.
Page 45
Troubleshooting en Fault Cause and troubleshooting E:32-00 will light up Water tap is jammed or furred up. alternately or indicator Turn on the water tap. ▶ for water supply lights The flow rate must be at least 10 l/min when the water supply is open.
Page 46
en Troubleshooting Fault Cause and troubleshooting E:61-03 will light up Not an appliance fault. Siphon connection is still alternately. Water is closed or the wastewater hose is kinked or blocked. not drained. Check the connection to the siphon and open if ne- cessary.
Page 47
Troubleshooting en Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. ‒ Pull out the mains plug or switch off the fuse in ‒...
Page 48
en Troubleshooting Fault Cause and troubleshooting Remnants of food on tableware. Filters are inserted incorrectly and/or not engaged. Insert the filters properly. → "Filter system", Page 41 Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. ▶ → "Programmes", Page 18 Tableware has been precleaned too intensely.
Page 49
Troubleshooting en Fault Cause and troubleshooting Removable streaks Do not place tableware or fragrance dispensers in are present on the tablet collecting tray. glasses, glassware Tableware has been precleaned too intensely. The with a metallic appear- sensors chose a weaker programme. Stubborn soiling ance and cutlery.
en Transportation, storage and disposal Insert the pump cover and press 18.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
Customer Service en 19.2 Protect appliance from 19.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely.
en Customer Service Customer Service for a period of at least 10 years from the date on which your appliance was placed on the market within the European Eco- nomic Area. Note: Under the terms of the manu- facturer's warranty the use of Cus- tomer Service is free of charge.
Technical specifications en Technical specifications 21 Technical specifications Technical specifications Weight Max.: 60 kg Voltage 220 - 240 V, 50 Hz or 60 Hz Power rating 2000 - 2400 W Fuse 10 - 16 A Water pressure min. 50 kPa (0.5 bar) ¡ max. 1000 kPa (10 bar) ¡ Inlet rate Min. 10 l/min Water temperature Cold water.
Conformity essential requirements and other rel- A detailed Declaration of Conformity evant provisions of Directive can be found online at siemens- 2014/53/EU. home.bsh-group.com/uk/ among the A detailed RED Declaration of Con- additional documents on the product formity can be found online at page for your appliance.
Page 55
Declaration of Conformity en The manufacturer, BSH Hausgeräte GmbH deems that it has complied with provision 5.1-1 of ETSI EN 303 ¡ 645 v2.1.1 and, where relevant, provision 5.1-2 of ETSI EN 303 645 v2.1.1; provision 5.2-1 of ETSI EN 303 ¡...
Page 56
EN Manufactured by BSH Hausgeräte GmbH under the trademark licence of Siemens AG Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom BSH Hausgeräte GmbH Carl-Wery-Straße 34...