Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell PC45 Series
Summary of Contents for Honeywell PC45 Series
- Page 1 PC45 Series Printer Accessories User Guide...
- Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. HII makes no representation or warranties regarding the information provided in this publication.
-
Page 3: Table Of Contents
Installation ..........................11 Cutter Module..........................15 Out of the Box......................... 15 Installation ..........................15 Linerless Cutter Module ......................18 Out of the Box......................... 18 Installation ..........................18 Cutter Tray............................21 Out of the Box......................... 21 PC45 Series Printer Accessory User Guide... - Page 4 Out of the Box .........................31 Installation..........................31 Heavier Spring ..........................34 Out of the Box .........................34 Installation..........................34 Appendix A - Wall Mounting Template ............37 PC45 Wall Mounting Template ....................37 Mount Printer on a Wall ......................38 PC45 Series Printer Accessory User Guide...
-
Page 5: Customer Support
To search our knowledge base for a solution or to log into the Technical Support portal and report a problem, go to honeywell.com/PSStechnicalsupport. Product Service and Repair Honeywell International Inc. provides service for all of its products through service centers throughout the world. Go to sps.honeywell.com and select Support to find a service center near you or to get a Return Material Authorization number (RMA #) before returning a product. - Page 6 PC45 Series Printer Accessory User Guide...
-
Page 7: Chapter 1 - Introduction
CHAPTER INTRODUCTION Honeywell offers a range of optional accessories for the PC45 series printers. Caution: Before you begin, turn off the printer and disconnect the power cord and communication cables. Accessories The following accessories are available for the printers: •... -
Page 8: Setup Printer
Load Media Note: The procedure for loading media is same for all the PC45 series printers. For simplicity, the PC45d printer is depicted in the illustrations. Pull one or both of the printer latches toward the front of the printer and lift the printer lid. - Page 9 Make sure the holders are snug against the sides of the media roll, and then press the locking tab down to lock the media holders in place. Note: Pull the media forward to make sure the media rotates and is not resting at the base of the printer. PC45 Series Printer Accessory User Guide...
- Page 10 For PC45t printer, thread the media through the media guides and past the front of the printer. To adjust the width of the media guides, slide the guides as PC45 Series Printer Accessory User Guide...
- Page 11 Note: Ensure the sides of the media is not crushed. PC45 Series Printer Accessory User Guide...
-
Page 12: Load Ribbon
Load Ribbon Place the new ribbon roll between the rear ribbon holders. The ribbon should come off the roll. Place the takeup core between the front takeup core holders. PC45 Series Printer Accessory User Guide... - Page 13 Attach the end of the ribbon to the takeup core. Turn the slack-wheel to take up slack in the ribbon. PC45 Series Printer Accessory User Guide...
-
Page 14: Notchless Ribbon Core Adapter
Insert one adapter into the media core and one adapter into the takeup core. 1 inch 0.5 inch Center the media roll and takeup core on the adapter. Press the release button and raise the print mechanism. PC45 Series Printer Accessory User Guide... - Page 15 1 inch For 0.5 inch notchless ribbon core, turn the slack-wheel until the notchless ribbon core adapter aligns with the slack-wheel. Route the ribbon under the print mechanism and up to the takeup core. PC45 Series Printer Accessory User Guide...
- Page 16 Attach ribbon to the takeup core. Turn the slack-wheel to take up slack in the ribbon. PC45 Series Printer Accessory User Guide...
-
Page 17: Chapter 2 - Installing Accessories
INSTALLING ACCESSORIES This chapter describes how to install accessories on the printer. Label Dispenser The label dispenser accessory for the PC45 series printer self-strips the label and removes the liner from the self-adhesive label stock. Out of the Box •... - Page 18 Slide the printer front door up and remove it from the printer. Press the platen roller latches apart and tilt them up to remove it from the printer. PC45 Series Printer Accessory User Guide...
- Page 19 Load Ribbon for PC45t printer (See page Push in the buttons behind the tabs then press the tab forward to open the label dispenser front door. Remove the label closest to the end of the liner. PC45 Series Printer Accessory User Guide...
- Page 20 11. Close the front door. 12. Close the printer lid until it snaps shut. 13. Turn the printer on and configure the feed adjust settings. PC45 Series Printer Accessory User Guide...
-
Page 21: Out Of The Box
The cutter module for PC45 series printer allows you to print on non-adhesive, continuous label stock. Out of the Box Use these instructions to install the cutter in the PC45 series printer. You will find the following items in the shipping box. •... - Page 22 Slide the printer front door up and remove it from the printer. Slide the cutter module down to the front of the printer until it locks in place. Load media (See page Load Ribbon for PC45t printer (See page PC45 Series Printer Accessory User Guide...
- Page 23 Thread media into the slot in the cutter accessory and out through the front of the cutter. Close the printer lid until it snaps shut. PC45 Series Printer Accessory User Guide...
-
Page 24: Out Of The Box
Warning: You must not use the cutter to cut through any kind of adhesive, or other soft material that may stick to the cutting parts and render the cutter inoperable or even damage the electric motor. Installation Open the media lid. PC45 Series Printer Accessory User Guide... - Page 25 Slide the printer front door up and remove it from the printer. Slide the cutter module down to the front of the printer until it locks in place. Load media (See page PC45 Series Printer Accessory User Guide...
- Page 26 Thread media into the slot in the cutter accessory and out through the front of the cutter. PC45 Series Printer Accessory User Guide...
-
Page 27: Out Of The Box
Use these instructions to install the cutter tray in the PC45d and PC45t printer. You will find the following items in the shipping box. • Cutter Tray Installation Slide the cutter tray onto the grooves on the cutter module. PC45 Series Printer Accessory User Guide... -
Page 28: Out Of The Box
• External Media Holder • Two Base plates • One M6x8 Phillips head screw • Six M3x8 Phillips head screws Installation Affix the cable mount on the base plate. PC45 Series Printer Accessory User Guide... - Page 29 Insert the media arm guide onto the holder and secure it with the M6x8 Phillips head screw. Secure the holder onto the base plate using four M3x8 Phillips head screws. PC45 Series Printer Accessory User Guide...
- Page 30 The printer alignment lines are provided on the base plate for reference. PC45d PC45t Align the printer with the screws on the base plate. Insert and pull the printer forward to secure in place. PC45 Series Printer Accessory User Guide...
- Page 31 Place an empty paper core on the media holder. Thread the media on top of the empty core and media guides as you would for the media installed inside the printer. PC45 Series Printer Accessory User Guide...
-
Page 32: Out Of The Box
Wi-Fi/Bluetooth Module The Wi-Fi/BT accessory for the PC45 series printer allows you to communicate with the printer wirelessly. Use the installation procedure to carefully install the module. Out of the Box • Wi-Fi/BT module with Antenna • NFC tag sticker Installation Note: This procedure applies to both the PC45d and PC45t printers. - Page 33 Move the U.FL cable from the printer aside and place the Wi-Fi/BT module onto the PCB. Connect the U.FL cable from the printer to the first U.FL connector. PC45 Series Printer Accessory User Guide...
- Page 34 Insert the Wi-Fi/BT antenna in the antenna slot. Connect the U.FL cable from the Wi-Fi/BT antenna to the second U.FL connector. Close the Wi-Fi/BT module slot door. PC45 Series Printer Accessory User Guide...
- Page 35 Push the media window from the inside of the printer lid and gently remove it. Apply force in the upper part of the media window. This piece has less resis- tance than the hooks section. Peel the NFC tag sticker and stick on the dedicated tag position. PC45 Series Printer Accessory User Guide...
- Page 36 Replace the media window. PC45 Series Printer Accessory User Guide...
-
Page 37: Out Of The Box
Thermal Printhead The thermal printhead for PC45 series printers is available in 203 and 300 dpi. The installation procedure is same for all the printer models. Out of the Box • Thermal printhead Installation Turn off the printer and disconnect the power cord. - Page 38 Detach the magnetic pressure arm from the printhead bracket and disconnect the two cables from the existing printhead as you remove it from the printer. Connect the ribbon cable to the new printhead. PC45 Series Printer Accessory User Guide...
- Page 39 Press the printhead onto the locator pins in the mechanism. Tilt the printhead up into the printer lid and press it into place. When the printhead is in correct position, the printhead latches snap into place on the sides of the printhead. PC45 Series Printer Accessory User Guide...
-
Page 40: Out Of The Box
Pull one or both of the printer latches toward the front of the printer and lift the printer lid. For thermal printer, remove the ribbon. Press the printhead latches apart until the existing printhead slides forward. Rotate the existing spring counterclockwise and remove it from the printhead mechanism. PC45 Series Printer Accessory User Guide... - Page 41 Insert the heavier spring onto the spring holder and rotate clockwise to secure in place. Tilt the printhead up into the printer lid and press it into place. PC45 Series Printer Accessory User Guide...
- Page 42 PC45 Series Printer Accessory User Guide...
-
Page 43: Appendix A - Wall Mounting Template
APPENDIX WALL MOUNTING TEMPLATE PC45 Wall Mounting Template 12.8 cm (5.0 in) 10.4 cm (4.1 in) PC45 Series Printer Accessory User Guide... -
Page 44: Mount Printer On A Wall
6 to 8 mm (0.24 to 0.33 in). • Honeywell recommends that you use pan-head or flathead screws with appropriate anchors for drywall, or for cement, concrete block, or plasterboard walls. Use wood screws only for wooden surfaces, and ensure the screw is long enough to be sunk to a depth of at least 12.5 mm (0.5 in).ecting a mounting... - Page 46 Honeywell 855 S. Mint Street Charlotte, NC 28202 www.sps.honeywell.com ™ PC45-ACC-EN-UG Rev B 07/23...