English Safety Plug and Fuse Information Care and Cleaning Parts List To Use Your Stand Mixer 9-14 Usage Diagrams and Usage Instructions 9-11 Usage Chart 12-14 Recipes To Assemble Your Creaming Beater 15-16 To Fit And Use Your Splashguard 16-17 Tool Adjustment Cord Storage Service and Customer Care...
If the plug or cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer in order to avoid a hazard. Always turn the speed control to ‘O’ Off position and unplug before fitting or removing tools/attachments, after use and before cleaning.
Page 5
Children should be supervised to ensure that they do not play with the appliance. Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.
The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service). Plug Type G This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to come into contact with food.
Page 7
Creaming beater Always remove the flexible wiper blade from the tool before cleaning. Wash the flexible wiper blade and tool in hot soapy water, then dry thoroughly. Alternatively the parts can be washed in a dishwasher. Note: Please inspect the condition of the tool body before and after use and also regularly inspect the condition of the wiper blade and replace it if there are any signs of wear.
To Use Your Stand Mixer Usage Diagrams and Usage Instructions...
Page 12
Important Ensure that no bowl tools are fitted or stored in the bowl when using other outlets. Do not use the whisk for heavy mixtures (e.g. all in one cakes or creaming fat and sugar) - you could damage it. Never exceed the maximum capacities and speeds stated –...
Page 13
Hints and Tips - K-Beater For best results, always use room temperature butter and margarine when making cakes. Use cold ingredients for pastry unless your recipe says otherwise. Hints and Tips - Whisk Best results achieved when eggs are at room temperature. Before whisking egg whites, make sure there is no grease or egg yolk on the whisk or the bowl.
Usage Chart (Mins) (MAX) 2 kg Min–Max 2–5 Min–1 2–3 680 g 2 kg Min–Max (Mins) (MAX) 2 kg Min–Max 2–5 2 kg Min–Max 1.5 kg Min–Max 2.68 kg Min–Max 2–5...
Page 15
(Mins) (MAX) Min–Max (420 g) Min–Max 2–3 4-8˚C 10 secs 1–1.5 250 g 500 g 200 g 1–1.5 180 ml (Mins) (MAX) Total 3–4 1.35 kg 2.17 kg Total 3–4 1.35 kg 2.28 kg Total 4–9 1.35 kg 2.93 kg...
(Mins) (MAX) 2–8 250 g Recipes White Bread Dough 1.35kg Flour 13.5g Salt 21.5g Fast Action Dried Yeast 756 ml Water 27g Lard or Butter Fit the bowl to the stand mixer. Pour the water into the bowl, followed by the remaining ingredients. Mix on minimum speed for 45-60 seconds or until a dough is formed.
To Assemble the Creaming Beater Usage Diagrams and Usage Instructions Important The wiper blade is supplied already fitted and should always be removed for cleaning. Carefully fit the flexible wiper blade onto the tool by locating the base of the wiper blade into the slot, then fit one side into the groove before gently hooking the end in place.
Raise the mixer head until it locks. Fit the bowl onto the base. Push the splashguard onto the underside of the mixer head until fully located. The hinged section should be positioned as shown. Insert required tool. Lower the mixer head. Remove the splashguard by raising the mixer head and sliding it down.
Creaming beater Ideally it should be in contact with the bowl surface so that it gently wipes the bowl during mixing. Using a suitable spanner loosen the nut sufficiently to allow adjustment of the shaft. To lower the tool closer to the bottom of the bowl, turn the shaft anti-clockwise. To raise the tool away from the bottom of the bowl turn the shaft clockwise.
If your Kenwood product malfunctions or you find any defects, please send it or bring it to an authorised KENWOOD Service Centre. To find up to date details of your nearest authorised KENWOOD Service centre visit www.kenwoodworld.com or the website...
Troubleshooting Guide Problem Cause Solution The whisk or K-beater Tool at the wrong height Adjust the height using a suitable knocks against the and needs adjusting. spanner – see “Tool Adjustment” bottom of the bowl section. or not reaching the ingredients in the bottom of the bowl.