Page 2
Welcome! Dear Customer, Thank you for choosing the Beko product. We want your product, manufactured with high quality and technology, to offer you the best efficiency. Therefore, carefully read this manual and any other documentation provided before using the product.
Table of Contents 1 Safety Instructions......General Safety....... Electrical Safety ......Product Safety ......Intended Use ......... Child, Vulnerable Persons and Pet Safety ........Transportation Safety ....2 Environmental Instructions..Waste Directive ......2.1.1 Compliance with the WEEE Dir- ective and Disposing of the Waste Product ......
1 Safety Instructions • This section includes the General Safety safety instructions necessary • This product can be used by to prevent the risk of personal children 8 years of age and injury or material damage. older, and people who are un- •...
• This product is not intended • Call the authorized service for for use by persons (including the installation of the product children) with limited physical, to be used. The warranty term sensory or mental capacity or starts after this process. without knowledge or experi- •...
ufacturer, the manufacturer's Product Safety service centre or a similar • Height between the bottom qualified person. surface of your hood and the • If the cable is damaged, con- top surface of the oven should tact our nearest service centre be no less than 650 mm for and have a new one installed.
Page 7
• Do not expose the appliance be fully insulated from the ex- to open flame. It may cause haust of this product or they the oil accumulating in the fil- must be hermetical. ter to catch fire. Do not oper- •...
• Our company shall not be re- Child, Vulnerable sponsible for problems that Persons and Pet Safety arise for not observing any of • Keep children away from the the warnings above. product when it is running. • There is a risk of fire if clean- •...
• Do not put other items on the tightly with tape to prevent the product and carry the product removable or moving parts of upright. the product and the product • When you need to transport from getting damaged. the product, wrap it with •...
3 Your product 3.1 Product Introduction 1 Hood body 2 Hood glass lid 3 Damper 4 Aluminium filter 5 Lamp 6 Lamp 7 Aluminium filter lock 8 Control panel Wall mounting part Dependent on the model. It may not be avail- able on your product.
Page 11
Air router Flue connection adapter Covers to prevent reverse airflow EN / 11...
3.3 Technical Specifications Product external dimensions (height/width/depth) (mm) min. 910 - max. 1138 /595 /419 Voltage/Frequency 220-240 V ~1N; 50 Hz Total power consumption max. 300 W Suction power 700-720 m3/h Diameter of air outlet pipe 120-150 mm Control Model A 3 levels Model B 3 levels + 1 booster...
4 Using the Hood The hood has an engine with various MODEL C speeds. For a good performance, we re- commend using low speeds under normal conditions and high speeds in case of strong odour and vapour condensation. The program is cancelled if power is cut when any program in your hood is active.
Page 14
In intensive ventilation mode, when You can only change the light col- any speed key is touched, it returns our shade while the lamp has high to that speed level and continues light intensity. to operate. In the event of a power outage, Operating the lamp your hood will remember the colour 1.
Page 15
Things to consider when using the "Hob If the ambient temperature differ- to Hood" function: ence occurs even when the hob is • If the pot is positioned in the right front not operating while the automatic eye of the hob in such a way that the mode is active, the temperature view angle of the sensor is blocked, the sensor in the product will detect...
touch the Speed 2 key for more than 3 If you run your hood at any speed seconds, carbon filter fill warning is reset level with the aluminium filter fill and the lamp is turned off. warning, the warning will not ap- pear for as long as the hood is run- The warning is not cancelled if the ning.
5.2 Aluminium Filter This filter serves to retain oil particles in the air. It is recommended to clean the filter once a month under normal usage. To achieve this: 1. Remove the aluminium filters. 2. Wash the filters in water using liquid detergent and reinstall after drying.
3. Place the lug slots of your new carbon 4. Close the hood glass cover after in- filters into the lugs on the motor holder stalling the aluminium filter. and turn them clockwise to snap them into place. 6 Troubleshooting If the problem persists after following the “Hob to Hood”...