Auxiliary Controls - GE AZ61H12DAB Owner's Manual And Installation Instructions
Heat/cool and heat pump models
Hide thumbs
Also See for AZ61H12DAB:
- Owner's manual & installation instructions (72 pages) ,
- Owner's manual (32 pages)
Table of Contents
Advertisement
Available languages
Available languages
Auxiliary controls on your Zoneline.
GEApUion e . o
[ MODE 1
[ MODE 2
Auxiliary
Controls--Aux
Set Button
The auxiliary set controls are located behind
the room cabinet, below the control panel.
Removethe room cabinet. See the To Remove
the Room Cabinet section.
The owner is responsible for ensuring the auxiliary
controls are set to the desired function. There are 9
different modes that can be set using the auxiliary
set button. To change modes, press AU,_SET('AU"
appears on the display).Pressthe mode button on
the control pad until the first digit in the display
shows the number corresponding to the mode you
are choosing and the correct HEAT/COOL LEDis lit.
Pressthe up or down arrow (shown in the second
digit of the display)to make the mode setting
selection where applicable. Pressthe AUXSET
button to confirm the selection.
AuxiliarySet Button
R
irst Digit
L_
Second
Digit
Press "Mode"
Press _ / W
I
Smart
Fan
-Cycb
/
b_
_ Continue
t
......
U
cool
B
Load
Shedding
hwl
L,t - Off
- On
/
Sentinel
HSA1
coo_
Y
COOL
HEAT
t
Constant
_
O: 60F_85F
O: 60F_65F
Fan
J
1: 64F-85F
1: 60FWOF
Temperature
I
2: 66F-85F
2 60F-72F
Limit
_.A_
_
3: 67F-85F
3: 6OFW4F
C004
Class 2
4: 70F-85F
4: 60F°76F
Mode
5: 72F-85F
5: 60FW8F
6: 74F-85F
6: 60F_80F
t_'_
Duct Mode
7: 76F-85F
7: 60F_85F
!
B
All 12R Mode
(Az6_ Only)
B'_ - On
- off
Lt
/
Boost
Heat
(AZ61
Orlmy)
Smart Fan--Cooling/Heating
The default setting for Mode I is as follows:
Cooling:Continuous (ON)
Heating: Cycle (OFF)
PressMODE until a 1 appears in the first digit of the
display for Stoat1:Fan cool mode. The COOLLED
light on the main control will be on.To change to
heat mode, press MODE again. The HEATLEDlight
on the main control will be lit. Pressthe down arrow
to set the indoor fan to cycle on/off when the unit is
heating or cooling "u."
Pressthe up arrow to set
the indoor fan to run continuously "n." This is
shown in the second digit of the display. PressAUX
SETto confirm your selection and exit AUXSET
mode, or press MODE to continue setting other
functions.
#
--
HIGH
I
COOL
LJ
--
LOW
--FAN
--AUTO
--HEAT
Cooling- Cycle
t P'_
--
HIGH
ICOOL
--
LOW
--
FAN
--AUTO
--HEAT
Cooling- Continuous
t
--
HIGH
--COOL
LJ
--
LOW
--FAN
--AUTO
_HEAT
Heating- Cycle
lh"_
--HIGH
--COOL
--
LOW
--
FAN
--
AUTO
I
HEAT
Heating- Continuous
Load Shedding (Central Desk Control)
The default setting for Mode 2 is OFF.
This feature is active only if the unit is connected to
a CDCand the CDChas control. PressMODE until a
2 appears in the first digit of the display for Load
Shedding mode. Pressthe down arrow for OFF"u"
or the up arrow for ON" n." This is shown in the
second digit of the display.When this mode is on,
only the indoor fan can be turned ON or OFFwith
the unit controls. When this mode isoff, all
operation is disabled except Heat/FreezeSentinel
(Mode3).PressAUXSETto confirm your selection
and exit AUXSETmode, or press MODEto continue
setting other functions.
_7
_in
Eu
E
Cover
Load
Load
Shedding
Shedding
OFF
ON
5
- Quick Links:
- Troubleshooting Tips
Hide quick links:
Advertisement
Chapters
Table of Contents
