Page 1
Dell™ Inspiron™ 4100 Solutions Guide w w w . d e l l . c o m | s u p p o r t . d e l l . c o m...
Page 2
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, DellNet, DellPlus, Dell TravelLite, TrueMobile, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, and DellWare are trademarks of Dell Computer Corporation;...
Safety and EMC Instructions: Portable Computers The following information defines the meaning of additional symbols used only in the Safety and Electromagnetic Compatibility (EMC) Instructions. Risk of explosion Aircraft Risk of fire Use of this feature may be prohibited on aircraft Risk of electric shock Safety Instructions General...
Page 10
• Do not allow your portable computer to operate with the base resting directly on exposed skin for extended periods of time. The surface temperature of the base will rise during normal operation (particularly when AC power is present). Allowing sustained contact with exposed skin can cause discomfort or, eventually, a burn.
Page 11
Power (Safety Instructions, continued) • Use only the Dell-provided AC adapter approved for use with this computer. Use of another AC adapter may cause a fire or explosion. • Before you connect the computer to an electrical outlet, check the AC adapter voltage rating to ensure that the required voltage and frequency match the available power source.
Page 12
Battery (Safety Instructions, continued) • Use only Dell battery modules that are approved for use with this computer. Use of other types may increase the risk of fire or explosion. • Do not carry a battery pack in your pocket, purse, or other container where metal objects (such as car keys or paper clips) could short-circuit the battery terminals.
Use shielded signal cables to ensure that you maintain the appropriate EMC classification for the intended environment. For parallel printers, a cable is available from Dell. If you prefer, you can order a cable from Dell at its world-wide website at http://accessories.us.dell.com.
When Using Your Computer Observe the following safety guidelines to prevent damage to your computer: • When setting up the computer for work, place it on a level surface. • When traveling, do not check the computer as baggage. You can put your computer through an X-ray security machine, but never put your computer through a metal detector.
If your computer gets wet or is damaged, follow the procedures described in "If Your Computer Gets Wet" on page 56. If, after following these procedures, you confirm that your computer is not operating properly, contact Dell (see page 103 for the appropriate contact information). Ergonomic Computing Habits...
Page 16
• Always use the palm rest with the keyboard, touch pad, or track stick. Leave space to rest your hands when using an external mouse. • Let your upper arms hang naturally at your sides. • Sit erect with your feet resting on the floor and your thighs level. •...
When Removing or Replacing Parts Before removing or installing memory modules, or adding a modem or Mini PCI card, perform the following steps in the sequence indicated. NOTICE: The only time you should ever access the inside of your computer is when you are installing memory modules, or adding a modem or Mini PCI card.
Page 18
You can also take the following steps to prevent damage from electrostatic discharge (ESD): • When unpacking a static-sensitive component from its shipping carton, do not remove the component from the antistatic packing material until you are ready to install the component. Just before unwrapping the antistatic packaging, be sure to discharge static electricity from your body.
S E C T I O N 1 S e t t i n g U p Connecting a Printer Transferring Information to a New Computer ® (Windows XP Only) Setting Up a Home and Office Network (Windows XP Only) Turning Off the Computer About the Module Bay Enabling the Infrared Sensor...
Connecting a Printer See the documentation that came with the printer for any recommended preparation procedures, such as: • Removing the packaging • Installing the toner or ink cartridge • Loading paper Then follow the instructions that came with the printer to connect it to the computer.
screws (2) parallel connector on computer parallel connector on printer clips (2) parallel printer cable notches (2) Turn on the printer and then turn on the computer. If the Add New Hardware Wizard window appears, click Cancel. Install the printer driver if necessary (see page 22). USB Printer Install the printer driver if necessary (see page 22).
USB connector on back of computer USB connector on printer USB printer cable Installing the Printer Driver If you need to install a printer driver, insert the installation CD into the CD or DVD drive. Then follow the prompts on the screen and use the instructions that came with the printer.
Transferring Information to a New ® Computer (Windows XP Only) Windows XP provides a Files and Settings Transfer Wizard to move data, such as e-mails, window sizes, toolbar settings, and Internet bookmarks, from one computer to another. First you collect the data from the source computer, and then you import the data to the new computer.
Complete the checklist and required preparations, and then return to HINT: Selecting the This computer connects the Network Setup Wizard. directly to the Internet Follow the instructions on the screen. connection method enables the integrated firewall provided with Turning Off the Computer Windows XP .
• Second battery • Dell TravelLite™ module NOTICE: To prevent damage to the docking connector, do not remove or replace devices while the computer is connected to an advanced port replicator (APR). Swapping Devices While the Computer Is Turned Off Save and close any open files, exit any open programs, and shut down the computer (see page 24).
Enabling the Infrared Sensor Turn on your computer, and enter the system setup program by HINT: You cannot use the infrared sensor when the pressing when the Dell™ logo appears. computer is docked. Se t t i n g U p...
Serial Port and Modem COM ports. Press the down-arrow key to highlight Fast IR or Slow IR. Dell recommends that you use Fast IR. If the infrared device cannot communicate with your computer, turn off the computer and repeat this procedure to change the setting to Slow IR.
Some surge protector manufacturers include warranty coverage for certain types of damage. Dell recommends that you carefully read the device warranty when choosing a surge protector. Compare joule ratings to determine the relative effectiveness of different devices.
See the surge protector documentation for modem connection instructions. NOTICE: Network adapter protection is not available on surge protectors. Dell recommends that you disconnect the network cable from the network wall jack during electrical storms. Line Conditioners NOTICE: Line conditioners do not protect against power interruptions.
S E C T I O N 2 S o l v i n g P r o b l e m s Finding Solutions Accessing Help Power Problems Error Messages Video and Display Problems Sound and Speaker Problems Printer Problems Modem and Internet Connection Problems Scanner Problems Touch Pad or Mouse Problems...
See the Tell Me How help file for more information on standby mode. Get technical assistance from Dell. See page 103. ® See page 36. So l v i n g P r o bl e m s...
Page 33
See page 38. See page 40. See page 41. See page 42. See page 46. See page 47. See page 48. See page 49. See page 49–53 See page 53. See page 36. See page 54. See page 42. See page 56. See page 58.
Accessing Help O A C C E S S T HE HE LP F I L E Tell Me How ® ® Microsoft Windows Click the Start button and then click Help and Support. Click User and system guides and then click User’s guides. Click Tell Me How.
If the battery status light rapidly flashes orange, the battery may be defective. Contact Dell (see page 103). E S T TH E E L E C T R I C A L O UT LE T —...
H E C K T HE O W E R R O P E R T I E S See the Tell Me How help file or — search for the keyword standby in the Help and Support Center (Help in Windows Me and Windows 2000).
Page 37
R E Q UI R E D FI LE W A S N O T F O U ND The program that you are . D L L — trying to open is missing an essential file. Remove and then reinstall the program. Windows XP Click the Start button.
• If the power light is blinking, the computer is in standby mode—press the Dell recommends that you power button to exit standby mode. attach an external monitor to your computer.
If the display is difficult to read D J U S T T HE B R I G HTN E S S Press to increase the brightness, — or press to decrease the brightness. O V E T HE S UB W O O F E R A W A Y FR O M T HE C O M P U TE R O R MO NI TO R —...
Turn on the computer and the monitor and adjust the monitor brightness and contrast controls. If the external monitor works, the computer display or video controller may be defective. Contact Dell (see page 103). Sound and Speaker Problems If you have a problem with integrated speakers...
D J U S T T HE I ND O W S V O L UM E C O NT R O L In Windows XP , click the — gray speaker icon in the lower-right corner of your screen. In Windows Me and Windows 2000, double-click the yellow speaker icon in the lower-right corner of the screen.
E R I FY TH AT TH E P R I N T E R I S R E C O G NI Z E D B Y I ND O W S Windows XP Click the Start button. Click Control Panel. Click Printers and Other Hardware.
E R I FY TH A T TH E P R IN T E R I S R E C O G NI Z E D B Y I ND O W S Windows XP Click the Start button. Click Control Panel. Click Printers and Other Hardware.
Page 44
H E C K T HE C O N NE C T I O N Verify that the telephone line is connected to — the modem. H E C K T HE TE L E P HO NE L I NE —...
Page 45
UR N O F F C A L L W A I TI N G C A TC H P H O N E See your telephone ) — directory for instructions on deactivating this feature. Then adjust the dial-up networking connection properties.
H E C K T HE S C A N NE R C A B LE C O NNE C TI O N Ensure that the scanner — cable is firmly connected to the computer and to the scanner. N L O C K TH E S C A NN E R —...
O V E R I FY T H A T T HE PR O B L E M I S W I T H T HE E X TE R NA L KE Y B O A R D C HE C K T HE I N TE G R A TE D KE Y B O A R D Turn off the computer.
Page 50
NS UR E T HA T T HE D I S K I S N O T W R I T E P R O TE C TE D You cannot save — data to a write-protected disk. See the following figure. back of floppy disk not write-protected write-protected...
If you cannot play a DVD movie HINT: Because of different worldwide file NS UR E T HA T I ND O W S R E C O G N I Z E S T HE D R I V E In Windows XP , —...
HA NG E TH E W R I TE S P E E D TO A S L O W E R R A T E See the help files for — your CD creation software. LO S E A LL O TH E R O PE N P R O G R A M S —...
H E C K T HE NE TW O R K L I G HT S O N T HE N E T W O R K C O N NE C T O R — Green indicates that the network connection is active. If the status light is not green, try replacing the network cable.
A solid blue screen appears UR N THE C O M P UT E R O FF If the computer does not respond to a — keystroke or a proper shutdown (see page 24), press the power button until the computer turns off.
Perform this procedure only after you are certain that it is safe to do so. If the computer is connected to an electrical outlet, Dell recommends that you turn off AC power at the circuit breaker before attempting to remove the power cables from the electrical outlet.
Replace the memory modules, the memory module cover, and the screw(s). Turn on the computer and verify that it is working properly. The Dell logo should appear, along with the following message: No operating system found Turn off the computer by pressing the power button.
If you cannot solve your problem using the Dell™ support — website or e-mail service, call Dell for technical assistance (see page 103). See "Dell Technical Support Policy (U.S. Only)" on page 100 for a description of the hardware and software support provided by Dell. Reinstalling Drivers and Utilities The Dell Drivers and Utilities CD for your computer contains drivers for operating systems that may not be on your computer.
To install a driver or utility from your Drivers and Utilities CD: Save your work in all open programs. Insert your Drivers and Utilities CD into the CD or DVD drive. In most cases, the CD should start running automatically. If it does ®...
Page 60
Windows XP Save and close any open files, exit any open programs, and insert the Drivers and Utilities CD into the CD or DVD drive. Click the Start button, and click Control Panel. Under Pick a category, click Performance and Maintenance. Under or pick a Control Panel icon, click System.
Click Update Driver. Verify that Automatic search for a better driver (Recommended) is selected, and then click Next. Click Finish, and then click Yes to restart the computer. Windows 2000 Save and close any open files, exit any open programs, and insert your Drivers and Utilities CD.
Click the Start button, and then right-click My Computer. Click Properties. Click the Hardware tab, and then click Device Manager. In the Device Manager window, right-click the device for which the new driver was installed and then click Properties. Click the Drivers tab. Click Roll Back Driver.
If an IRQ conflict exists, the Device status area in the Properties window reports what other devices are sharing the device's IRQ. Resolve any IRQ conflicts. You can also use the Windows XP Hardware Troubleshooter. To use the troubleshooter, click the Start button and click Help and Support. Type in the Search field, and then click the arrow hardware troubleshooter to start the search.
You can also use the Windows Me Hardware Troubleshooter. To use the troubleshooter, click the Start button and click Help. Click Troubleshooting in the What would you like help with? list, click Hardware & system device problems, click Hardware, memory, & others, and then click Hardware Troubleshooter.
Using System Restore Windows XP and Windows Me provide a System Restore feature that allows you to return your computer to an earlier operating state if changes to the computer’s hardware or software (including new hardware or program installations) or other system settings, have left the computer in an undesirable operating state.
Click File System. Click the Troubleshooting tab, and make sure that Disable System Restore is not checked. Before proceeding with any System Restore function, Dell recommends that you thoroughly read Microsoft’s information about using System Restore. To access this information: Click the Start button, point to All Programs (point to Programs in Windows Me) —>Accessories —>System Tools, and then click...
Type a name for the new restore point in the Restore point description field. The present date and time are automatically added to the description of the new restore point. Click Create (click Next in Windows Me). Click OK (click Close in Windows Me). Restoring the Computer to an Earlier Operating State If problems occur after you install a device driver, first try using Device Driver Rollback (see page 59).
The Operating System CD provides options for reinstalling the Windows XP operating system. The options can potentially overwrite files installed by Dell and possibly affect programs installed on your hard drive. Therefore, Dell does not recommend that you reinstall your operating system unless instructed to do so by a Dell technical support representative.
Page 69
Press any key when the message Press any key to boot from CD appears on the screen. When the Windows XP Setup screen appears, press <Enter> to select To set up Windows now. Read the information in the License Agreement window, and then press <F8>...
The Operating System CD provides options for reinstalling your Windows Me operating system. The options can potentially overwrite files installed by Dell and possibly affect programs installed on your hard drive. Therefore, Dell does not recommend that you reinstall your operating system unless instructed to do so by a Dell technical support representative.
Page 71
Press to save your changes and exit the system setup program. Press any key to boot the computer from the CD. At the Welcome window, click OK. Double-click Refresh Windows OS. Click OK. Click OK again. The installation takes 25-45 minutes. Remove the Operating System CD from the drive, and click OK to restart your computer.
The Operating System CD provides options for reinstalling the Windows 2000 operating system. The options can potentially overwrite files installed by Dell and possibly affect programs installed on your hard drive. Therefore, Dell does not recommend that you reinstall your operating system unless instructed to do so by a Dell technical support representative.
When the Windows 2000 Professional Setup window appears, press the arrow keys to select the Windows 2000 partition option that you want. Then press the key for the partition option you chose. When the Windows 2000 Professional Setup window reappears, press the arrow keys to select the type of file system that you want Windows 2000 to use, and then press .
S E C T I O N 3 R e p l a c i n g Pa r t s Using the Advanced Port Replicator Adding Memory Adding a Mini PCI Card Replacing the Hard Drive Adding a Daughter Card Modem...
Using the Advanced Port Replicator The advanced port replicator (APR) integrates your computer into a HINT: If you receive a BIOS upgrade floppy disk desktop environment. The APR includes a network adapter to connect your with your APR, use the computer to a network.
Page 77
Connector Icon (continued) Connector Description Connect a PS/2-compatible mouse. Connect a serial device, such as a serial mouse or digital camera. Connect a network interface cable. Connect a parallel device, such as a printer. Connect an external monitor. Connect the AC adapter. The audio line-out connector is on the side of the APR.
APR. NOTICE: Always use the Dell AC adapter that came with the APR. If you use any other commercially available AC adapter—or the AC adapter from other Dell computers—you may damage the APR or the computer.
Disconnect any external devices, and remove any PC Cards from the computer. Connect the AC adapter to the connector on the APR, and connect the AC power cable to an electrical outlet. Horizontally center the computer on the APR base, with the back of the computer facing the APR docking connector.
Page 80
NOTICE: If you do not use correct undocking procedures, you may lose data and the computer may not restart. Save and close all open files and exit all open programs. Perform one of the following procedures: • Click the Start button, and then click Eject PC. After a few seconds, the computer power light turns off.
Before working inside your computer, read "When HINT: Memory modules Removing or Replacing Parts" on page 17. purchased from Dell are covered under your Save and close any open files, exit any open programs, and shut down computer warranty. the computer (see page 24).
Page 82
Remove all installed batteries, and disconnect the AC adapter cable and any external devices from the computer. Wait 5 seconds before proceeding. Ground yourself by touching a metal connector on the back of the computer. NOTICE: While you work, periodically touch unpainted metal on the computer to dissipate static electricity that might harm internal components.
Page 83
memory module securing clip NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled "JDIM (DIMMA)" before you install a module in the connector labeled "JDIM2 (DIMMB)." Ground yourself and install the new memory module: Align the notch in the module with the slot in the center of the HINT: If the memory...
Page 84
Replace the cover and screw(s). NOTICE: If the memory module cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer. screw (2) memory module cover Re pl a c i n g Par t s...
Adding a Mini PCI Card If you ordered a Mini PCI card at the same time that you ordered your computer, Dell has already installed the card for you. Make sure that the work surface is flat and clean to prevent scratching the computer cover.
Page 86
If a Mini PCI card is not already installed, go to step 11. If you are replacing a Mini PCI card, remove the existing card: Disconnect the Mini PCI card from the antenna cables. screws (2) memory module cover To release the Mini PCI card, spread the metal securing tabs until the card pops up slightly.
antenna cables (2) antenna connectors on antenna computer (2) connectors on card (2) Lower the Mini PCI card toward the inner tabs to approximately a 20-degree angle. Continue lowering the Mini PCI card until it snaps into the inner tabs of the socket.
Page 88
To replace the hard drive in the hard drive bay: HINT: Dell does not guarantee compatibility Save and close any open files, exit any open programs, and shut down or provide support for the computer (see page 24). hard drives from sources other than Dell.
Use the Drivers and Utilities CD to install the drivers and utilities for your computer (see page 58). Returning a Hard Drive to Dell Return your old hard drive to Dell in its original or comparable foam packaging. Otherwise, the hard drive may be damaged in transit. hard drive...
Adding a Daughter Card Modem If you ordered the optional modem at the same time that you ordered your computer, Dell has already installed the modem for you. Make sure that the work surface is flat and clean to prevent scratching the computer cover.
Page 91
pull tab modem cable connector modem cable Connect the modem cable to the modem. NOTICE: The cable connectors are keyed for correct insertion; do not force the connections. Align the modem with the screw hole(s) and press the modem into the connector on the system board.
S E C T I O N 4 A p p e n d i x Specifications Standard Settings Returning Items for Warranty Repair or Credit Dell Technical Support Policy (U.S. Only) Contacting Dell Returning Items for Warranty Repair or Credit Limited Warranties and Return Policy...
Specifications Microprocessor ® ® Microprocessor types Intel Mobile Pentium III-M L1 cache 32 KB (internal) L2 cache 512 KB Math coprocessor internal to microprocessor Processor speed various depending on configuration External bus frequency 133 MHz System Information System chip set Intel 830M Data bus width 64 bits...
Page 95
4-pin USB-compliant connector Infrared sensor compatible with IrDA Standard 1.1 (Fast IR) and IrDA Standard 1.0 (Slow IR) Docking 200-pin connector for a Dell docking device S-video TV-out 7-pin mini-DIN connector (an S-video to composite video adapter optionally included with the computer)
Page 96
Ports and Connectors (continued) Modem RJ-11 port (optional) Ethernet LAN RJ-45 port (optional) Communications Modem: Type v.92 56K MDC Controller softmodem Interface internal AC 97 bus Network adapter 10/100 Ethernet LOM Video Video type 128-bit hardware accelerated Data bus 4X AGP Video controller ATI Mobility RADEON or NVidia GeForce2 Go-200...
Page 97
Audio (continued) Internal speaker amplifier 1.0-W channel into 4 ohms Volume controls keyboard shortcuts, program menus Display Type (active-matrix TFT) XGA; SXGA+; UXGA Dimensions: Height 214.3 mm (8.4 inches) Width 285.7 mm (11.3 inches) Diagonal 357.1 mm (14.1 inches) Maximum resolutions 1024 x 768 at 16.8 million colors (XGA), 1400 x 1050 at 16.8 million colors (SXGA+) Response time (typical)
Page 98
Keyboard (continued) 19.05 mm ± 0.3 mm (0.75 inch ± 0.012 inch) Key spacing Layout QWERTY/AZERTY/Kanji Touch Pad X/Y position resolution (graphics table mode) 240 cpi Size: Width 64.88 mm (2.55-inch) sensor-active area Height 48.88-mm (1.92-inch) rectangle Track Stick X/Y position resolution (graphics table mode) 250 count/sec @ 100 gf Size...
Page 99
Battery (continued) Life span (approximate) 500 discharge/charge cycles Temperature range: Operating 0° to 35°C (32° to 95°F) Storage –40° to 65°C (–40° to 149°F) AC Adapter Input voltage 90 to 264 VAC Input current (maximum) 1.7 A Input frequency 47 to 63 Hz Output current 4.5 A (maximum at 4-second pulse);...
Page 100
Physical (continued) Weight (with 8-cell battery): 2.4 kg (5.3 lb) with travel module 2.6 kg (5.7 lb) with floppy drive 2.6 kg (5.8 lb) with CD drive Environmental Temperature range: Operating 0° to 35°C (32° to 95°F) Storage –40° to 65°C (–40° to 149°F) Relative humidity (maximum): Operating 10% to 90% (noncondensing)
NOTICE: Unless you are an expert computer user or are directed to do so by Dell technical support, do not change the settings for this program. Certain changes might make your computer work incorrectly. Viewing the System Setup Screens Turn on (or restart) your computer.
All Dell-standard components included in a Custom Factory Integration (CFI) project are covered by the standard Dell limited warranty for your computer. However, Dell also extends a parts replacement program to cover all nonstand- ard, third-party hardware components integrated through CFI for the duration of the computer’s service contract.
Page 104
See "Dell Technical Support Policy (U.S. Only)" on page 100 for a description of the hardware and software support provided by Dell. Country (City) Department Name or Service Area, Area Codes, International Access Code Website and E-mail Address Local Numbers, and...
Page 105
International Access Code: 0021 Tech Support Fax 55 51 481 5470 Country Code: 55 Sales 0800 90 3366 City Code: 51 Website: http://www.dell.com/br Brunei Customer Technical Support (Penang, Malaysia) 604 633 4966 Country Code: 673 Customer Service (Penang, Malaysia) 604 633 4949...
Page 106
Country Code: 420 02 22 83 27 14 City Code: 2 TechFax 02 22 83 27 28 Switchboard 02 22 83 27 11 Website: http://support.euro.dell.com E-mail: czech_dell@dell.com Denmark (Horsholm) Technical Support 45170182 International Access Code: 00 Relational Customer Care 45170184...
Page 107
09 253 313 38 City Code: 9 Home/Small Business Customer Care 09 693 791 94 09 253 313 99 Switchboard 09 253 313 00 Website: http://support.euro.dell.com E-mail: fin_support@dell.com France (Paris/Montpellier) Home and Small Business International Access Code: 00 Technical Support 0825 387 270...
Page 108
Preferred Accounts Customer Care 06103 766-9420 Large Accounts Customer Care 06103 766-9560 Public Accounts Customer Care 06103 766-9555 Switchboard 06103 766-7000 Website: http://support.euro.dell.com E-mail: tech_support_central_europe@dell.com Guatemala General Support 1-800-999-0136 Hong Kong Technical Support toll free: 800 96 4107 International Access Code: 001...
Page 109
Country Code: 39 Customer Care 02 696 821 14 City Code: 02 02 696 821 13 Switchboard 02 696 821 12 Website: http://support.euro.dell.com E-mail: http://support.euro.dell.com/it/it/emaildell/ Corporate Technical Support 02 577 826 90 Customer Care 02 577 825 55 02 575 035 30...
Page 110
Technical Support Outside of Japan (Dimension and Inspiron) 81-44-520-1435 Technical Support (Dell Precision™, OptiPlex™ toll free: 0120-1984-33 and Latitude™) Technical Support Outside of Japan (Dell 81-44-556-3894 Precision, OptiPlex, and Latitude) 24-Hour Automated Order Service 044 556-3801 Customer Care 044 556-4240...
Page 112
Corporate Sales 020 581 8818 Corporate Sales Fax 020 686 8003 020 686 8003 Switchboard 020 581 8818 Website: http://support.euro.dell.com E-mail: tech_nl@dell.com New Zealand Home and Small Business 0800 446 255 International Access Code: 00 Government and Business 0800 444 617...
Page 113
Home/Small Business Customer Care 23162298 Switchboard 671 16800 Fax Technical Support (Upplands Vasby, Sweden) 46 0 85 590 05 594 Fax Switchboard 671 16865 Website: http://support.euro.dell.com E-mail: nor_support@dell.com E-mail Support for Servers: Nordic_server_support@dell.com Panama General Support 001-800-507-0962 Peru General Support...
Page 114
Sales 011 709 7700 Country Code: 27 011 706 0495 City Code: 11 Switchboard 011 709 7700 Website: http://support.euro.dell.com E-mail: dell_za_support@dell.com Southeast Asian and Pacific Customer Technical Support, Customer Service, 604 633 4810 Countries and Sales (Penang, Malaysia) Spain (Madrid)
Page 115
Sales 08 590 05 185 Website: http://support.euro.dell.com E-mail: swe_support@dell.com E-mail Support for Latitude and Inspiron: Swe-nbk_kats@dell.com E-mail Support for OptiPlex: Swe_kats@dell.com E-mail Support for Servers: Nordic_server_support@dell.com Switzerland (Geneva) Technical Support (Home and Small Business) 0844 811 411 International Access Code: 00...
Page 116
Preferred Accounts (500-5000 employees) 01344 723196 Customer Care Central Government Customer Care 01344 723193 Local Government Customer Care 01344 723194 Home/Small Business Sales 0870 907 4000 Corporate/Public Sector Sales 01344 860456 Website: http://support.euro.dell.com E-mail: dell_direct_support@dell.com Ap pe nd i x...
Page 117
International Access Code: 011 AutoTech (for portable and desktop computers) toll free: 1-800-247-9362 Country Code: 1 Dell Home and Small Business Group (for portable and desktop computers): Customer Technical Support (Return Material toll free: 1-800-624-9896 Authorization Numbers) Customer Technical Support (Home sales toll free: 1-877-576-3355 purchased via http://www.dell.com)
Returning Items for Warranty Repair or Credit Prepare all items being returned, whether for repair or credit, as follows: Call Dell to obtain an authorization number, and write it clearly and prominently on the outside of the box. For the telephone number to call, see the contact numbers for your region.
Once you have determined your computer’s FCC classification, read the appropriate FCC notice. Note that FCC regulations provide that changes or modifications not expressly approved by Dell could void your authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: •...
Page 120
FCC regulations: • Model number: PP01L • Company name: Dell Computer Corporation One Dell Way Round Rock, Texas 78682 USA Modem Regulatory Information This equipment complies with Part 68 of the FCC rules. On the bottom of...
Page 121
If you experience trouble with this telephone equipment, see “Contacting Dell” on page 103 to find the appropriate contact information for obtaining customer assistance. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Fax Branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent, identification of the business, other entity, or individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual.
(NOM): Exporter: Dell Computer Corporation One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, S.A. de C.V. Paseo de la Reforma 2620 - 11° Piso Col. Lomas Altas 11950 México, D.F . Ship to: Dell Computer de México, S.A.
3.5 A Limited Warranties and Return Policy Dell-branded hardware products purchased in the U.S. or Canada come with either a one-year limited warranty, a two-year limited warranty, or a three-year limited warranty. To determine which warranty you purchased, see the Dell invoice that accompanied your computer. The following...
Dell, usage not in accordance with product instructions, failure to perform required preventive maintenance, and problems caused by use of parts and components not supplied by Dell. This limited warranty does not cover any items that are in one or more of the following categories: software;...
Page 126
Before you ship the product(s) to Dell, back up the data on the hard drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as floppy disks, CDs, or PC Cards. Dell does not accept liability for lost data or software.
If Dell elects to exchange a product or portion of a product, the exchange will be made in accordance with Dell’s Exchange Policy in effect on the date of the exchange.
Page 128
Before you ship the product(s) to Dell, back up the data on the hard drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as floppy disks, CDs, or PC Cards. Dell does not accept liability for lost data or software.
Page 129
You will pay Dell for replacement parts if the replaced part is not returned to Dell. The process for returning replaced parts, and your obligation to pay for replacement parts if you do not return the replaced parts to Dell, will be in accordance with Dell’s Exchange Policy in effect on the date of the...
If Dell elects to exchange a system or component, the exchange will be made in accordance with Dell’s Exchange Policy in effect on the date of the exchange. In any instance in which Dell issues a Return Material Authorization Number, Dell must receive the product(s) for repair prior to the expiration of the warranty period in order for the repair(s) to be covered by the limited warranty.
Page 131
Before you ship the product(s) to Dell, back up the data on the hard drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as floppy disks, CDs, or PC Cards. Dell does not accept liability for lost data or software.
Page 132
You will pay Dell for replacement parts if the replaced part is not returned to Dell. The process for returning replaced parts, and your obligation to pay for replacement parts if you do not return the replaced parts to Dell, will be in accordance with Dell’s Exchange Policy in effect on the date of the...
If Dell elects to exchange a system or component, the exchange will be made in accordance with Dell’s Exchange Policy in effect on the date of the exchange. In any instance in which Dell issues a Return Material...
Page 134
Before you ship the product(s) to Dell, back up the data on the hard drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as floppy disks, CDs, or PC Cards. Dell does not accept liability for lost data or software.
If Dell elects to exchange a product or portion of a product, the exchange will be made in accordance with Dell’s Exchange Policy in effect on the date of the exchange.
Page 136
Before you ship the product(s) to Dell, back up the data on the hard drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as floppy disks, CDs, or PC Cards. Dell does not accept liability for lost data or software.
Page 137
The warranty term for a replacement part is the remainder of the limited warranty term. You will pay Dell for replacement parts if the replaced part is not returned to Dell. The process for returning replaced parts, and your obligation to pay for replacement parts if you do not return the replaced parts to Dell, will be in accordance with Dell’s Exchange Policy in effect on the date of the...
If Dell elects to exchange a system or component, the exchange will be made in accordance with Dell’s Exchange Policy in effect on the date of the exchange. In any instance in which Dell issues a Return Material...
Page 139
Before you ship the product(s) to Dell, back up the data on the hard drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as floppy disks, CDs, or PC Cards. Dell does not accept liability for lost data or software.
Page 140
The warranty term for a replacement part is the remainder of the limited warranty term. You will pay Dell for replacement parts if the replaced part is not returned to Dell. The process for returning replaced parts, and your obligation to pay for replacement parts if you do not return the replaced parts to Dell, will be in accordance with Dell’s Exchange Policy in effect on the date of the...
Page 141
If Dell elects to exchange a system or component, the exchange will be made in accordance with Dell’s Exchange Policy in effect on the date of the exchange. In any instance in which Dell issues a Return Material...
If you are an end-user customer who bought reconditioned or refurbished products from a Dell company, you may return them to Dell within 14 days of the date of invoice for a refund or credit of the product purchase price. In either case, the refund or credit will not include any shipping and handling charges shown on your invoice.
Dell Computer Corporation ("Dell") warrants to the end user in accordance with the following provisions that its branded hardware products, purchased by the end user from a Dell company or an authorized Dell distributor in Latin America or the Caribbean, will be free from defects in materials, workmanship, and design affecting normal use, for a period of one year from the original purchase date.
Page 144
Guarantee will be the end user’s sole and exclusive remedy against Dell or any of its affiliates, and neither Dell nor any of its affiliates shall be liable for loss of profit or contracts, or any other indirect or consequential loss arising from negligence, breach of contract, or howsoever.