hit counter script
Dell 4100 Service Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Server
  5. Dimension 4100
  6. Service manual
Dell 4100 Service Manual

Dell 4100 Service Manual

Dell poweredge 4100 servers: service manual
Hide thumbs Also See for 4100:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Manual
Dell
PowerEdge
4100/180 and 4100/200 Systems
®
®
SERVICE MANUAL
®

Advertisement

Table of Contents
loading

Related Manuals for Dell 4100

Summary of Contents for Dell 4100

  • Page 1 Dell PowerEdge 4100/180 and 4100/200 Systems ® ® SERVICE MANUAL ®...
  • Page 2 Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

  • Page 3: System Overview

    RAID capability, hot-pluggable SCSI hard-disk drives, thermal and power supply monitoring, redundant fans, and ECC memory. The PowerEdge 4100 systems are freestanding or can be rackmounted to integrate your servers. The microprocessor modules are installed in zero insertion force (ZIF) sockets on the system board, which allow you to replace microprocessors faster.
  • Page 4 “Running the System Diagnostics” in Chapter 2.) For a complete list of system features, see “Technical Specifications” found later in this chapter. For information about installing the PowerEdge 4100 systems in a rack, see the “Dell PowerEdge 4100 and 6100 Systems Rack Kit Installation Guide”...
  • Page 5 back of computer left side front of computer Figure 1-1. Computer Orientation NOTE: When following the text in this manual, assume that the location or direction relative to the system is as shown in Figure 1-1. right side System Overview...
  • Page 6 Before using the reset button to initiate a hardware reset, close any open application programs and files if possible. If you are using < Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual reset button SCSI hard-disk drive SCSI hard-disk drive...
  • Page 7 expansion slots system board microprocessor sockets cooling fan connectors (3) (cooling fans are located behind the air intake panel) Figure 1-3. Front/Left Internal View external drive bays (4) control panel internal drive bays (6) hard-disk drive security lock air intake panel System Overview...
  • Page 8 (ultra-wide) internal drive bays (6) SCSI backplane board SCSI power connector control panel connector Figure 1-4. Back/Right Internal View Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual server management connector power supply (optional) power supply SMB connector SCSI connector port...
  • Page 9 keylock power supply (optional) cable strain relief power supply red LED green LED AC power receptacle Figure 1-5. I/O Panel SMB connector SCSI connector port keylock video connector server-management serial port connector parallel port connector serial port 2 connector serial port 1 connector mouse connector keyboard connector security cable slot...

  • Page 10: System Memory

    System Memory The PowerEdge 4100 systems have a minimum of 64 MB of 72-bit-wide, buff- ered EDO memory. The system memory capacity can be expanded to 1024 MB (1 GB) by using combinations of 32- and 128-MB buffered, EDO dual in-line memory modules (DIMMs) having gold connectors.

  • Page 11: Video Controller

    SCSI hard-disk drive bays. For detailed information about installing externally accessible drives, see Chapter 9, “Installing Drives in the External Bays,” in the Dell PowerEdge 4100/180 and 4100/200 Sys- tems Installation and Troubleshooting Guide. For detailed information about installing SCSI hard-disk drives, see Chapter 10, “Installing Drives in the Internal...

  • Page 12: Device Termination

    SCSI ID number from 0 to 7. For additional SCSI addressing informa- tion, see Chapter 10, “Installing Drives in the Internal Bays,” in the Installation and Troubleshooting Guide. When narrow SCSI devices are shipped from Dell, the default SCSI ID numbers are assigned as follows: •...

  • Page 13: System Unit

    ystem Unit The following subsections provide service-related information about the system unit. System Power Supply The 500-W system power supply can operate from an AC power source of 90 to 265 VAC at 50 or 60 Hz. When the power-supply paralleling board is installed, the power supplies are hot-pluggable.

  • Page 14: Pin Assignments For The Dc Power Connectors (Nonredun- Dant Systems)

    (J11, J12, J13, J14, and J15). The following illustrations show both sets of connectors. Figure 1-6. Power Supply Connectors Figure 1-7. Power Connector Panel 1-12 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual J12 (P2) J11 (P1) J15 (P5) J14 (P4)
  • Page 15 +5 VDC (red) –5 VDC (white) common (black) common (black) common (black) PSON# (gray) 14 15 16 17 18 19 J11 (P1) +5 VDC (red) common (black) +5 VDC sense (red) –sense (black) PWRGOOD (orange) +5 VFP (purple) Pin 13 — PSON# should measure between +4 and +5 VDC except when the power button on the front panel is pressed, taking PSON# to its active-low state.
  • Page 16 Figure 1-9. DC Power Connectors J12 (P2), J13 (P3), and J14 (P4) Figure 1-10. DC Power Connector J15 (P5) 1-14 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual +5 VDC (red) common (black) common (black) common (black) common (black) 10 11 12 13 14 15...
  • Page 17 DC Power Distribution (Nonredundant System) Figures 1-11 provides information about DC power distribution for the nonredundant PowerEdge 4100 system. P1–5 NRLED PWRGOOD PSON# PSON# +5 VFP +5 VFP power +5 VDC +5 VDC supply # 1 –5 VDC –5 VDC...

  • Page 18: Pin Assignments For The Dc Power Connectors (Redundant Systems)

    PWRSCSI, and PWRFD) or at the connectors on the end of the wire bundles extending from these connectors (PWR1, PWR2, PWR3, DDBP, and FD1–FD4). diagnostics port Figure 1-12. Power-Supply Paralleling Board Connectors 1-16 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual PWR1 PWRFD (FD1–FD4) PWR2 PWR3...
  • Page 19 NC_3INH common (black) POWER_GOOD (gray) common (black) +5 VFP (violet) 10 11 12 13 14 15 PWR1 -12 VDC (blue) -5 VDC (white) PWR_STAT_BIT (gray) C_SDA (gray) C_SCL (gray) Figure 1-13. DC Power Connector PWR1 +3.3 VDC (orange) common (black) +12 VDC (yellow) common (black) +12 VDC (yellow)
  • Page 20 Figure 1-15. DC Power Connector PWRSCSI (DDBP) Figure 1-16. DC Power Connector PWRFD (FD1–FD4) 1-18 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual common (black) common (black) common (black) common (black) 10 11 12 13 14 PWRSCSI (DDBP) +12 VDC (yellow)
  • Page 21 DC Power Distribution (Redundant System) Figures 1-17 provides information about DC power distribution for the redun- dant PowerEdge 4100 system. PWR1 P1–5 BATV PWRGOOD PSON# PSON# +5 VFP +5 VFP power +5 VDC +5 VDC supply # 1 –5 VDC –5 VDC...

  • Page 22: System Board Layout

    (SERIAL1) mouse connector (MOUSE) keyboard connector (KEYBOARD) Figure 1-18. System Board Components 1-20 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Ultra/Narrow SCSI host adapter connector (SCSI2 CD-ROM) secondary microprocessor socket (PROCESSOR2) Ultra/Wide SCSI host adapter connector (BACKPLANE SCSI1) power supply...

  • Page 23: Main Memory

    Main Memory The eight DIMM sockets on the system board can accommodate combinations of 32- and 128-MB DIMMs up to a total memory capacity of 1024 MB (1 GB). The system is shipped with high-speed (60-ns) 3.3-V EDO DIMMs installed. When reinstalling DIMMs, use the following guidelines: •...

  • Page 24: Interrupt Assignments

    IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 1-22 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table 1-2. Jumper Descriptions Description EISA Configuration Utility Integrated video controller Password enable/disable Reserved Microprocessor speed Microprocessor speed Table 1-3. Interrupt Assignments...

  • Page 25: Dma Channel Assignments

    Table 1-3. Interrupt Assignments IRQ Line Used/Available IRQ10 Available for use by expansion card IRQ11 Available for use by expansion card IRQ12 Generated by keyboard controller to indicate that mouse’s output buffer is full IRQ13 Generated by math coprocessor to indicate coprocessor error IRQ14 Available for use by expansion card IRQ15...

  • Page 26: Technical Specifications

    ... . . 120 pins PCI expansion-card connector data width (maximum) ..32 bits 1-24 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual echnical Specifications Table 1-5. Technical Specifications Microprocessor...
  • Page 27 Table 1-5. Technical Specifications System clock ....60 or 66 MHz (matches external processor bus Diskette/communications ports ....24 MHz from the system clock Architecture .
  • Page 28 SCSI hard-disk drive online indicator ....green LED 1-26 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table 1-5. Technical Specifications System Board Connectors (continued) POWER1 .
  • Page 29 Table 1-5. Technical Specifications Controls and Indicators (continued) SCSI hard-disk drive activity indicator ....green LED SCSI hard-disk drive fault indicator ....yellow LED Power-supply 5-VDC online indicator .
  • Page 30 Altitude: 1-28 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table 1-5. Technical Specifications Environmental (continued) Operating ... . . –16 to 3048 m (–50 to 10,000 ft) Storage ....–16 to 10,600 m (–50 to 35,000 ft)

  • Page 31: Basic Troubleshooting

    (A brief explanation of how to load and start the system diagnostics is located near the end of this chapter.) Dell recommends that you perform the fol- lowing procedures in the order they are presented in this manual.

  • Page 32: E Xternal Visual Inspection

    7. Inspect the keyboard to ensure that no keys are sticking. 8. Inspect the exterior of the computer, including all controls and indica- Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual xternal Visual Inspection monitor and peripherals, and their power sources.

  • Page 33: O Bserving The Boot Routine

    To observe problem indications during the boot routine, follow these steps: 1. If the system is off, turn on all peripherals and the computer. Insert the Dell Server Assistant CD into the CD-ROM drive. Press the reset but- ton or <Ctrl Del>...

  • Page 34: I Nternal Visual Inspection

    5. Observe the monitor screen for the Dell Server Assistant Menu. nternal Visual Inspection CAUTION: Before you proceed with the internal visual inspection described in this section, ensure that the user has saved all open files and exited all open application programs if possible.

  • Page 35: E Liminating Resource Conflicts

    To start the diagnostics, insert the CD into the CD-ROM drive, and then press the reset button on the computer. Restarting the computer causes the Dell Server Assistant logo screen to appear on the monitor screen, followed by a screen containing icons of the options available.

  • Page 36: Getting Help

    If no errors are found in main memory, and the Dell Server Assistant loads, select the Run System Utilities icon. Then select the Run System Diagnostics icon by pressing <Enter>. The Diagnostics Menu appears, allowing you to choose the following options or exit to MS-DOS: •...

  • Page 37: Beep Codes And Error Messages

    Chapter 3 Beep Codes and Error Messages his chapter describes beep codes and system error messages that can occur during system start-up or, in the case of some failures, during normal system operation. The tables in this chapter list faults that can cause a beep code or sys- tem error message to occur and the probable causes of the fault in each case.
  • Page 38 1-3-4-1 1-3-4-3 1-4-1-1 1-4-2-1 1-4-3-1 2-2-3-1 3-2-2-1 4-2-4-4 4-2-4-3 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table 3-1. Beep Codes Error Probable Causes No DIMM memory Defective DIMMs or system installed board. Reseat DIMMs or replace system board. DRAM failure Defective DIMMs or system board.

  • Page 39: System Error Messages

    ystem Error Messages Table 3-2 lists system error messages that can appear on the monitor screen. These messages can help you find the source of a problem. Some of these error messages indicate fatal errors. When a fatal error occurs, the system cannot usu- ally be rebooted until an appropriate hardware change has been made.
  • Page 40 System mem- ory size has changed - Run Config- uration Utility Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table 3-2. System Error Messages Definition Real-time clock on system board mal- functioned. Cable may be loose, keyboard may be...
  • Page 41 Table 3-2. System Error Messages Message Definition Wrong microprocessor Stepping of installed in CPU1 is less PROCESSOR1 socket. than sA1 - System halted. Wrong microprocessor Stepping of installed in CPU2 is less PROCESSOR2 socket. than sA1 - System halted. Wrong microprocessor Stepping of installed in system.
  • Page 42 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual...

  • Page 43: Removing And Replacing Parts

    Chapter 4 Removing and Replacing Parts his chapter provides procedures for removing the components, assemblies, and subassemblies in the system unit. Unless otherwise noted, each procedure assumes the following: • You have performed the steps in “Precautionary Measures” found later in this chapter.

  • Page 44: Precautionary Measures

    ESD. WARNING FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE EQUIPMENT: Only service technicians trained by Dell should perform the following procedures. Before you start to work on the com- puter, perform the following steps in the sequence listed.
  • Page 45 To remove a computer cover, follow these steps: 1. Turn the cover’s keylocks on the back panel of the computer to the unlocked position (see Figure 4-2) Figure 4-2. Keylocks on Computer’s Back Panel 2. Loosen the three screws along the back edge of the cover (see Figure 4-1).

  • Page 46: Front Bezel

    To remove the front bezel, follow these steps: 1. Remove the computer covers. 2. Release the two tabs on each side of the bezel. 3. Slide the front bezel toward the front of the computer. Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual...
  • Page 47 Drives Figure 4-4 shows an example of drive hardware that can be installed in the com- puter. Refer to this figure when you perform any of the procedures in the following subsections. DC power cable diskette/tape drive interface cable diskette drive interface connector (FLOPPY) SCSI connector (SCSI2 CD-ROM)

  • Page 48: Front-Panel Inserts

    A tab on each side of the insert snaps into a corresponding latch on the inside of the front bezel. Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual latch (2) until the tabs come loose from the bezel.

  • Page 49: Externally Accessible Drives

    Externally Accessible Drives 3.5-inch diskette drive in top bay CD-ROM drive in middle bay lower-bay drive position for optional drive drive-release tab(2) Figure 4-6. Externally Accessible Drives Removal All of the externally accessible drives have drive-mounting rails. To remove a drive assembly from one of the externally accessible drive bays, follow these steps: 1.
  • Page 50 3. Remove the drive-mounting rails from the drive (see Figure 4-7). 4. If the drive is a SCSI drive, record the setting of the SCSI address Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Figure 4-7. Drive-Mounting Rails Removal jumpers and SCSI bus termination jumper.

  • Page 51: Hard Disk Drives

    Hard-Disk Drives Figure 4-8. Hard-Disk Drive Carrier Removal The hard-disk drives are mounted inside a hard-disk drive carrier. The hard-disk drive carrier must be removed before a hard-disk drive can be removed. To remove a hard-disk drive, follow these steps: NOTES: Wait 20 seconds for the hard-disk drive to spin down before removing the hard-disk drive carrier.
  • Page 52 The online indicator (green) lights, indicating power is being supplied to the hard-disk drive. With the controller connected, the activity LED is activated when the controller spins up the drive. 4-10 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual screw (4) Figure 4-9. Hard-Disk Drive Removal carrier.

  • Page 53: Scsi Backplane Board

    CSI Backplane Board hard-disk drive carrier thumb screw Figure 4-10. SCSI Backplane Board Removal To remove the SCSI backplane board, follow these steps: 1. Disconnect the hard-disk drive carrier connectors from the SCSI back- plane board by sliding each carrier toward the front of the computer approximately 1 inch.

  • Page 54: Power Supply

    5. Slide the power supply out of the chassis. To replace a power supply, perform these steps in reverse order. 4-12 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual ower Supply (marked by a “0”). the other end of the cable from the power supply.

  • Page 55: P Ower-Supply Paralleling Board

    ower-Supply Paralleling Board cables thumb screw hook slots (11) Figure 4-12. Power-Supply Paralleling Board Removal (Redundant Systems) To remove a power-supply paralleling board, follow these steps: WARNING: Disconnect both power supplies from their AC power source to prevent the possibility of getting shocked. 1.

  • Page 56: P Ower Connector Panel

    2. Disconnect all power connector panel cables (from the system board, 3. Unscrew the retainer screw. 4. Disengage the panel from the four hooks holding it to the computer 4-14 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual ower Connector Panel power connector...

  • Page 57: Control Panel

    ontrol Panel screw control panel connector BP_to_CP Figure 4-14. Control Panel Removal To remove the control panel, follow these steps: 1. Remove the screw holding the control panel to the chassis. 2. Disconnect the cable from connector BP_to_CP. 3. Disengage the panel from the four hooks holding the panel to the computer chassis, and lift the panel away from the computer.

  • Page 58: Cooling Fans

    3. Press down the catch on the fan carrier, and remove the fan carrier 4. Remove the cooling fan from the fan carrier by releasing the two fan 4-16 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual ooling Fans fan carrier cooling fan nector on the system board.

  • Page 59: System Board Components

    ystem Board Components The subsections that follow contain procedures for removing system board components. Ultra/Narrow SCSI host adapter diskette/tape drive interface connector (SCSI2 CD-ROM) connector (FLOPPY) EISA connectors (EISA1 [top], EISA2, and EISA3) PCI connectors (PCI4 [top]–PCI8) battery connector (BATTERY) video connector (MONITOR) server-management...

  • Page 60: Expansion Cards

    4. If the card is a full-length expansion card, unlock the locking cam on 5. Grasp the expansion card by its corners, and carefully remove it from 4-18 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual locking card guide the locking card guide.
  • Page 61 DIMMs DIMM securing clip (2) Figure 4-18. DIMM Removal To remove a DIMM, push outward on the DIMM socket’s securing clips until the DIMM is released from its socket. Then lift the DIMM away from the socket. DIMM securing clip (2) Figure 4-19.

  • Page 62: Microprocessor And Heat Sink

    1. Remove the microprocessor securing clip from the microprocessor/heat 4-20 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual sink assembly. WARNING: The microprocessor chip can get extremely hot during system operations. Be sure the chip has had sufficient time to cool before touching it.
  • Page 63 heat sink release lever Figure 4-21. Microprocessor Securing Clip 2. Remove the heat sink. Push outward and then upward on the microprocessor release lever to rotate the lever to its fully vertical position. CAUTION: Be careful not to bend any of the pins when removing the microprocessor chip from its socket.
  • Page 64 If you are installing a new microprocessor and heat sink, place the thermal interface pad that comes with the replacement microprocessor between the microprocessor and the heat sink before reinstalling the securing clip. 4-22 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual pin-1 corner (gold finger and bevel)

  • Page 65: System Battery

    System Battery battery BATTERY socket Figure 4-24. System Battery Removal To remove the system battery, follow these steps: 1. If possible, enter the System Setup program, and make a printed copy of the system setup screens. 2. Remove the left computer cover. See “Computers Covers”...

  • Page 66: System Board

    4-24 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual ystem Board unit. a. Remove the screw that secures the system board to the vertical wall of the computer chassis.

  • Page 67: System Setup Program

    Appendix A System Setup Program his appendix describes the System Setup program, which is used to set or change the system configuration information stored in NVRAM on the system board. To enter the System Setup program, press <F2> during the power-on self-test (POST).

  • Page 68: Key Functions

    <Spacebar> <F9> <Alt><d> <F10> <Enter> <Alt><r> Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table A-1. Key Functions Function Displays the general help window Displays the Exit menu, or the parent menu if you are in a submenu Selects a different menu...

  • Page 69: Screen Color Combinations

    Also used to highlight the function keys in the key functions box. • White on black — The highlight color for an input field that is selected. Main Menu configuration options and system data box Dell System PowerEdge 4100/200 Setup Main Advanced Security Exit...
  • Page 70 Base Memory Extended Memory Video Memory Service Tag Asset Tag Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Table A-2. Main Menu Categories Function Resets time on system’s internal clock. Resets date on system’s internal calendar. Identifies type of diskette drives installed.

  • Page 71: Boot Options Submenu

    Boot Options Submenu Dell System PowerEdge 4100/200 Setup Main Advanced Security Exit Boot Options Boot Sequence: [A: then C:] Setup Prompt: [Enabled] POST Errors: [Enabled] Diskette Drive Check: [Enabled] Reset Button: [Enabled] Help Select Item Exit Select Menu Enter Figure A-2. Boot Options Submenu Table A-3.

  • Page 72: Advanced Menu

    Diskette Controller: On-Board SCSI A: On-Board SCSI B: PCI Scan Sequence Use MP Specification PS/2 Mouse Figure A-3. Advanced Menu Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Advanced Security Exit [3F8, IRQ 4] [2F8, IRQ 3] [378, IRQ 7]...
  • Page 73 Table A-4. Advanced Menu Categories Category Function Serial Port 1 or Configures system’s built-in serial ports. Serial Port 2 Parallel Port Configures system’s built-in parallel port. The port’s I/O address may be set to: 278H, IRQ5; 3BCH, IRQ7; 378H, IRQ7 Otherwise, the port may be disabled.

  • Page 74: Security Menu

    User Password Is Set Supervisor Password[Press Enter] Set User Password Password on Boot Diskette Access System Backup Reminder [Disabled] Virus Check Reminder Figure A-4. Security Menu Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Advanced Security Exit Disabled [Press Enter] [Disabled] [User]...
  • Page 75 Table A-5. Security Menu Categories Category Function Supervisor Password Is Displays current status of the supervisor password (enabled or disabled). See “Using the Supervisor Password Feature” in Chap- ter 4 of the User’s Guide. User Password Is Displays current status of user password (enabled or disabled).

  • Page 76: Exit Menu

    Main Save Changes & Exit Exit Without Saving Changes Get Default Values Load Previous Values Save Changes Figure A-5. Exit Menu A-10 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual Advanced Security Exit Help Select Item Exit Select Menu Enter...
  • Page 77 Table A-6. Exit Menu Categories Category Function Save Changes and Exit Saves the changes you have made before you exit the System Setup program. The next time you boot up, the BIOS configures your system according to the selections stored in CMOS Exit Without Saving Exits the System Setup program without Changes...
  • Page 78 A-12 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual...
  • Page 79 Index AC power receptacle about , 1-7 location on I/O panel , 1-7 battery connector , 4-17 illustrated , 4-23 removing and replacing , 4-23 BATTERY connector , 4-17 beep codes , 3-1 boot routine observing when troubleshooting cables DC power , 1-12 card-slot opening , 4-18...
  • Page 80 FLOPPY connector front bezel removal , 4-4 front-panel inserts removal , 4-6 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual , 1-23 , 1-9 , 1-10 , 1-10 , 1-8 , 4-17 , 4-18 , 4-17...
  • Page 81 memory main , 1-21 system , 1-8 messages, error , 3-3 microprocessor release lever , 4-21 removal , 4-20, 4-21 sockets , 4-17 microprocessor cooling fans removal , 4-16 MONITOR connector , 4-17 MOUSE connector , 4-17 mouse connector location on I/O panel , 1-7 location on system board , 4-17...
  • Page 82 , A-1 screen color combinations screen conventions security menu starting , A-1 Dell PowerEdge 4100/180 and 4100/200 Systems Service Manual , 1-7 , 4-17 , 4-17 , 1-7 , 4-17 , 4-17 , 1-24 , 1-8...

This manual is also suitable for:

Poweredge 4100/180Poweredge 4100/200

Table of Contents