Reading or writing the ECA information . . . Checkout guide ....System supporting the Lenovo ThinkVantage Chapter 8. Removing and replacing a Toolbox program and the PC-Doctor for DOS diagnostics program .
Page 4
1140 Bluetooth-wireless radio switch FPC ..Miscellaneous parts ... . 1150 System board, fan assembly, 34-mm ac power adapter ... . . ExpressCard reader, and base cover .
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
– Send another person to get medical aid. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury.
When handling ESD-sensitive parts: • Keep the parts in protective packages until they are inserted into the product. • Avoid contact with other people. • Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Hardware Maintenance Manual...
– “FRU identification for CTO, CMV, and GAV products” on page 33 Important: • Advise customers to contact the Lenovo Customer Support Center if they need any assistance in obtaining or installing any software fixes, drivers, and UEFI BIOS downloads. Telephone numbers for Lenovo Support are available at:http://www.lenovo.com/support/phone...
Dynamic Configure To Order (CTO) This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO”...
= a “fixed part number”, not “CTO” (Example: 1829-F1U). • PEW can be accessed at the following Web site: http://www.lenovo.com/support/site.wss/document.do?lndocid=LOOK-WARNTY Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION.
Page 40
1. Click Product & Parts Detail and then follow the instructions on the screen to reach the Product and Parts Details page. 2. Click the Parts Detail tab to view the list of service parts. Using the HMM For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory) Use the HMM as a back-up to PEW and eSupport to view the complete list of FRUs at the MT Model level.
“What to do first” on page 35 • “Checkout guide” on page 36 – “System supporting the Lenovo ThinkVantage Toolbox program and the PC-Doctor for DOS diagnostics program” on page 36 – “System supporting the Lenovo diagnostics programs” on page 40 •...
System supporting the Lenovo ThinkVantage Toolbox program and the PC-Doctor for DOS diagnostics program The section provides information about ThinkPad computers that support the Lenovo ThinkVantage Toolbox ® program and the PC-Doctor for DOS diagnostics program. Some descriptions might not apply to your particular computer.
Page 43
Note: PC-Doctor for DOS is available at the following Web site: http://www.lenovo.com/supportTo create the PC-Doctor diagnostic CD, follow the instructions on the Web site. For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem, you need to initialize the computer setup by use of the ThinkPad Setup before you run PC-Doctor.
Page 44
The options on the test menu are as follows: Diagnostics Interactive Tests • Run Normal Test • Keyboard • Run Quick Test • Video • CPU/Coprocessor • Internal Speaker • System Memory • Mouse • Systemboard • Diskette • Video Adapter •...
Page 45
While the Windows operating system is running, press the ThinkVantage button. To start this program, do the following: • Click Start ➙ Control Panel ➙ System and Security ➙ Lenovo - System Health and Diagnostics. Windows Vista and Windows XP: Click Start ➙...
Touch Pad does not correct the problem, continue with the following: • Interactive Tests ➙ Mouse. System supporting the Lenovo diagnostics programs The section provides information about ThinkPad computers that support the Lenovo diagnostics programs. Some descriptions might not apply to your particular computer. The Lenovo diagnostics programs include following: •...
Page 47
F12 key. 3. Press the Tab key to switch to the Application Menu window. 4. Use the arrow keys to select Lenovo Diagnostics and then press Enter. The main screen of the UEFI diagnostic program is displayed.
If the computer you are servicing is not installed with the UEFI diagnostic program, you can download a bootable diagnostic program from the Lenovo Support Web site. The bootable diagnostic programs enable you to test computer memory and internal storage devices, view system information, and check and recover the internal storage devices.
2. Remove the battery pack. 3. Connect the ac power adapter. 4. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the ac power adapter and install the charged battery pack. 7.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature.
Page 51
5. Measure the voltage of the backup battery. See the following figure. Wire Voltage (V dc) +2.5 to +3.2 Black Ground • If the voltage is correct, replace the system board. • If the voltage is not correct, replace the backup battery. •...
“Symptom-to-FRU index” on page 52 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/support Restoring the factory contents by using Product Recovery discs When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no Product Recovery program is on the new drive.
Page 54
The recovery disc set consists of the user instructions and the following set of DVDs to restore the computer to the original factory configuration. ® Operating System Recovery Disc (one disc) This disc restores the Microsoft Windows operating system. Use this disc to start the recovery process. Applications and Drivers Recovery Disc (one or This disc restores the preinstalled applications and more discs)
If it has, it can be used for access to the hard disk drive. If no master hard disk password is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master hard disk password, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
Attention: If User only mode is selected and the user hard disk password has been forgotten and cannot be made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user hard disk passwords or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears. 2. Select Power off display (keep current power plan) (in Windows XP, keep current power scheme). You can also put the computer into screen blank mode, press ThinkVantage button and use the ThinkVantage Productivity Center.
Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it before resuming normal operation. If you do undock it and then try to resume normal operation, you will get an error message, and you will have to restart the system. To cause the computer to enter hibernation mode, do any of the following: •...
Numeric error codes Table 2. Numeric error codes Symptom or error FRU or action, in sequence 0177 System board. Bad SVP data, stop POST task—The checksum of the supervisor password in the EEPROM is not correct. 0182 1. Run ThinkPad Setup. Press F9, and Enter to load Bad CRC2.
System board. This system does not support batteries that are not Replace the battery. genuine Lenovo-made or authorized. The system will continue to boot, but may not charge unauthorized batteries. ATTENTION: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use.
• This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later. • Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any replacement LCD will have zero pixel defects.
Page 64
Table 7. Status indicators Indicator Meaning Speaker mute The speaker is on mute. To set the speakers on mute or unmute, press Orange: the speaker mute button. Microphone mute Orange: The microphone is on mute. None of the recording devices is available while the microphone mute is on by default.
Page 65
Table 7. Status indicators (continued) Indicator Meaning Sleep (standby for Green: The computer is in sleep (standby) mode. Windows XP) status Blinking The computer is entering sleep (standby) mode or hibernation mode, green: or is resuming normal operation. Battery status Green: The battery charge level is 20% or higher.
Page 68
Table 8. Fn key combinations (continued) Key combination Description • External monitor only Note: To switch between the computer display and an external monitor, the Win+P key combination is also available. For Windows Vista and Windows XP: Switch a display output location •...
CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
If you replace the system board, you must restore the serial number of the system unit to its original value. Before replacing the system board, save the original serial number by doing the following: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
CRU; and (2) you may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
Some models of the ThinkPad T420s and T420si you are servicing might have the SIM card that the customer has installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See 1010 Battery pack.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue. If Lenovo ThinkVantage Toolbox is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced. Note that the replacement of a physically damaged battery pack is not covered by the warranty.
Table 10. Removal steps of Serial Ultrabay Slim device or travel bezel Holding the bay lock latch in the unlocked position , slide the bay eject latch in the direction shown by arrow , and then pull out the Serial Ultrabay Slim device or the travel bezel in the direction shown by arrow completely remove it 1030 Solid state drive (SSD) or hard disk drive (HDD) For access, remove the FRU:...
Page 77
Removal steps of SSD or HDD Torque Step Screw (quantity) Color M3 × 3 mm, flat-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the SSD or HDD is firmly attached. Chapter 8 Removing and replacing a FRU...
For HDD and HDD rubber rails: For SSD and SSD spacers: 1040 DIMM For access, remove this FRU: • “1010 Battery pack” on page 68 Removal steps of DIMM Note: Remove the screws Hardware Maintenance Manual...
Page 79
Step Screw (quantity) Color Torque M2 × 5 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Chapter 8 Removing and replacing a FRU...
When installing: Insert the notched end of the DIMM into the socket. Press the DIMM in firmly, and pivot it until it snaps into place. Make sure that it is firmly attached in the slot and does not move easily. 1050 PCI Express Mini Card for wireless LAN For access, remove this FRU: •...
Page 81
Step Screw (quantity) Color Torque M2 × 5 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Note: Some models might have only two antenna cables. Chapter 8 Removing and replacing a FRU...
When installing: • In models with a wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M, and the black cable into the jack labeled AUX or A on the card. If the computer you are servicing has three cables, put the white cable in the cable protection tube.
Page 84
Step Screw (quantity) Color Torque M2 × 5 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Hardware Maintenance Manual...
Torque Step Screw (quantity) Color M2 × 3 mm, small-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Plug the orange cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card. 1070 4–in–1 media card reader For access, remove this FRU: •...
Removal steps of 4–in–1 media card reader 1080 Keyboard For access, remove this FRU: • “1010 Battery pack” on page 68 Removal steps of keyboard Note: Remove the screws Step Screw (quantity) Color Torque M2 × 5 mm, flat-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm)
Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 5 mm, flat-head, nylon-coated (2) (1.85 kgfcm) Slightly press the keyboard and slide it a little bit forward, in the direction shown by arrow , to detach the front edge of the keyboard from the frame. Then, lift up the keyboard in the direction shown by arrow Lift the keyboard a little in the direction shown by arrow , and then detach the connector Chapter 8...
Page 88
Installation steps of keyboard When installing the keyboard, do the following: 1. Attach the keyboard connector. Hardware Maintenance Manual...
2. Attach the keyboard so that the keyboard edge is under the frame as shown in the following figure. 3. Gently press the keys with your palms and slightly slide the keyboard toward you until it snaps into position. 4. Secure the keyboard by tightening the screws from the bottom side of the computer. 1090 Backup battery For access, remove these FRUs in order: •...
• “1080 Keyboard” on page 80 DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Removal steps of backup battery When installing: Attach the backup battery in the insulation sheet as shown in the figure below and make sure that the battery connector is attached firmly.
Page 91
Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader is defective, you can replace the palm rest by following the procedures in this section. The replacement procedures are the same for a palm rest with or without a fingerprint reader. Removal steps of palm rest or palm rest with fingerprint reader Step Screw (quantity)
Removal steps of speaker Torque Step Screw (quantity) Color M2 × 3 mm, flat-head, nylon-coated (4) Silver 0.181 Nm (1.85 kgfcm) 1110 LCD unit For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1080 Keyboard” on page 80 •...
Page 95
Removal steps of LCD unit Step Screw Screw (quantity) Color Torque M2.5 × 5 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4.0 kgfcm) Chapter 8 Removing and replacing a FRU...
When installing • Make sure that you route the cables firmly and tape up in the proper positions as shown in the figure above. • When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Step Screw (quantity) Color Torque 0.181 Nm M2 × 3 mm, shoulder-socket head, nylon-coated (1) Silver (1.85 kgfcm) 1130 Bluetooth daughter card (BDC-3.0) • “1010 Battery pack” on page 68 • “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 70 •...
Page 98
• “1060 PCI Express Mini Card for wireless WAN” on page 77 • “1070 4–in–1 media card reader” on page 79 • “1080 Keyboard” on page 80 • “1100 Palm rest with fingerprint reader, smart card reader, and speaker” on page 84 •...
1150 System board, fan assembly, 34-mm ExpressCard reader, and base cover Important notices for handling the system board: When handling the system board, read the following: • The system board has an accelerometer, which can be broken when several thousands of G-forces are applied.
Page 100
• “1070 4–in–1 media card reader” on page 79 • “1080 Keyboard” on page 80 • “1100 Palm rest with fingerprint reader, smart card reader, and speaker” on page 84 • “1110 LCD unit” on page 88 • “1120 DC-in sub card” on page 90 •...
Page 101
Step Screw (quantity) Color Torque Black 0.181 Nm M 2 × 9 mm, flat head, nylon-coated (1) (1.85 kgfcm) M2 × 3 mm, flat head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) Torque Step Screw (quantity) Color M2 × 5 mm, big-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm)
Page 102
In step , remove the system board with fan assembly together from the base cover assembly. Turn the system board over, and then disconnect the fan assembly from the system board. Step Screw (quantity) Color Torque Black 0.181 Nm M2 × 5 mm, big-head, nylon-coated (4) (1.85 kgfcm) When installing: •...
Page 103
• Make sure that the fan connector is attached firmly. Remove the three screws and then remove the 34-mm ExpressCard reader from the system board. Torque Step Screw (quantity) Color M2 × 3 mm, flat-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) Chapter 8 Removing and replacing a FRU...
Page 104
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. The following illustration shows the location of each label. Note: If the Windows Certificate of Authentication label (COA) is attached to a part that is replaced, return the old part with the label attached to the customer, or provide a letter to the customer stating what the label was originally on the system and what the label part number, serial number, and product key were.
IMEI/ESN label Onboard LAN MAC address label China Telecom label China 3G WWAN label Taiwan WWAN label Product label For some models, you may need to apply two FCC labels. Check the old base cover; if it has two FCC labels, apply both to the new base cover.
2020 LCD panel For access, remove these FRUs, in order: • “1010 Battery pack” on page 68 • “2010 LCD bezel assembly” on page 101 The LCD panel and the peripheral parts used in this product are very sensitive. Improper handling of the LCD panel can cause damage to the parts, and may cause a system malfunction such as a missing dot, missing line, or pixel problems.
Page 109
Removal steps of LCD panel Attention: Unplug the LCD cable by holding the left and right edges of the connector with your fingers, and gently pull the connector toward you. Do not unplug the cable by pulling it. Applying tension to the cable could cause the cable to be damaged or a wire to be broken.
When installing: When attaching the LCD panel to the cover, gently press the left and right edges covered with metal. Do not press the surface of the panel or apply any excessive force to the panel. 2030 Integrated camera, microphone, or hall sensor card For access, remove these FRUs, in order: •...
Page 111
Removal steps of integrated camera, microphone, or hall sensor card Torque Step Screw (quantity) Color M2 × 3 mm, small-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector of the integrated camera, microphone, or the hall sensor card is attached firmly. Chapter 8 Removing and replacing a FRU...
2040 LED sub card For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “2010 LCD bezel assembly” on page 101 • “2020 LCD panel” on page 102 Hardware Maintenance Manual...
Removal steps of LED sub card Step Screw (quantity) Color Torque M2 × 3 mm, small-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. 2050 LCD cable For access, remove these FRUs in order: •...
• “2010 LCD bezel assembly” on page 101 • “2020 LCD panel” on page 102 • “2030 Integrated camera, microphone, or hall sensor card” on page 104 • “2040 LED sub card” on page 106 Removal steps of LCD cable Cable routing: When you install the LCD cable, route the cable as shown in the figure above.
Page 115
• “2020 LCD panel” on page 102 • “2030 Integrated camera, microphone, or hall sensor card” on page 104 • “2040 LED sub card” on page 106 • “2050 LCD cable” on page 107 Removal steps of hinge kit Step Screw (quantity) Color Torque...
2070 LED cable For access, remove these FRUs in order: • “1010 Battery pack” on page 68 • “1020 Serial Ultrabay Slim device or travel bezel” on page 69 • “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 70 •...
Removal steps of LED cable Cable routing: When you install the LED cable, route the cable as shown in the figure below. 2080 Antenna kit and LCD rear cover assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 68 •...
Page 118
• “1110 LCD unit” on page 88 • “1120 DC-in sub card” on page 90 • “1140 Bluetooth-wireless radio switch FPC” on page 91 • “1150 System board, fan assembly, 34-mm ExpressCard reader, and base cover” on page 93 • “2010 LCD bezel assembly”...
Page 119
When you install the antenna kit, route the cables as shown in the figures below. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Rear view Status indicators DisplayPort connector 34-mm ExpressCard slot or 4-in-1 media card reader Always On USB connector slot Combo audio jack USB connector USB connector Ethernet connector Monitor connector ac power connector : For the description of each indicator, see Chapter 5 “Status indicators” on page 57. Bottom view Expansion slot (DIMM, PCI Express Mini Card for Battery pack latch...
CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You may find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You may be required to return the defective part that is replaced by the CRU.
Miscellaneous parts Table 14. Parts list—Miscellaneous parts FRU no. Screw kit 04W1693 Seal kit 04W1694 Base miscellaneous parts 04W1690 Keyboard bezel miscellaneous parts 04W1691 System miscellaneous parts: 04W1692 • (a) DIMM slot cover assembly • (b) Hard disk drive cover assembly •...
Recovery discs Windows XP Professional (32 bit) DVDs Note: The Windows XP Professional recovery DVDs are available only for models with a valid Microsoft Windows XP Professional certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing limitation, if a model came with Windows XP Professional preinstalled from the factory, but has either a Windows 7 or Windows Vista COA affixed to the system, that model is eligible only for recovery DVDs that match the operating system specified on the COA.
Table 21. Parts list—Windows Vista Home Basic (32 bit) recovery DVDs Language English 04T3646 Windows Vista Business (32 bit) DVDs Note: The Windows Vista recovery DVDs are available only for models with a valid Microsoft Windows Vista certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing limitation, if a model came with Windows Vista Business or Windows Vista Ultimate preinstalled from the factory, but has a Windows 7 COA affixed to the system, that model is eligible only for recovery DVDs that match the operating system specified on the COA.
Table 23. Parts list—Windows 7 Home Basic (32 bit) recovery DVDs (continued) Language 04T3687 Spanish Serbian-latin 04T3692 Turkish 04T3694 English 04T3695 Windows 7 Home Basic (64 bit) DVDs Windows 7 Home Basic (64 bit) is preinstalled as the operating system in the following models: •...
Table 26. Parts list—Windows 7 Ultimate (64 bit) recovery DVDs Language English 04T3684 Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: • 4170-CTO • 4171-CTO •...
Table 28. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs (continued) Language Japanese 04T3711 Korean (English-enable) 04T3712 Polish 04T3713 04T3714 Portuguese (English-enable) Romanian (English-enable) 04T3715 Russian 04T3716 04T3719 Serbian-Latin (English-enable) Simplified Chinese 04T3702 04T3717 Slovak (English-enable) Spanish 04T3718 04T3703 Traditional Chinese (English-enable) Traditional Chinese for Hong Kong S.A.R (English-enable) 04T3709...
USB floppy diskette drive for maintenance diskette 05K9283 USB floppy diskette drive tool kit 27L3452 42W7820 Test card for integrated Smart Card — LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later Note: Download the file from the following Web site: http://www.lenovo.com/support Hardware Maintenance Manual...
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
For electronic emission information on Class B digital devices, refer to the corresponding information in the User Guide. Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System Lenovo Rescue and Recovery...
Page 152
Part Number: 0A60241_04 Printed in China (1P) P/N: 0A60241_04 *0A60241_04*...