Siemens Washing machine Installation Instructions Manual
Hide thumbs
Also See for Washing machine:
- Operating instructions and installation (64 pages) ,
- Instruction manual and installation instructions (28 pages) ,
- Instruction manual (28 pages)
Advertisement
Table of Contents
Safety instructions
– The washing machine is heavy - take care when lifting.
– Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed
to frost or outdoors.
– The washing machine could be damaged. Do not lift the appliance by protruding
components (e.g. the washing machine door, the cover, the front panel or the outer door
in case of deco models).
– In addition to the instructions provided in this document, special regulations from the
relevant water and electric utility companies may apply.
– If in doubt, have a technician connect the appliance.
– Lay hoses and cables in such a way that there is no risk of tripping.
Installation surface
– The machine must be stable so that it does not move around.
– The installation surface must be firm and level.
– Soft floors/floor coverings are not suitable.
Installation on a pedestal
– The feet of the washing machine must be secured with holding brackets*.
* order no. WMZ20455, WZ20455
Installation on a wood joist floor
– If possible, place the washing machine in a corner.
– Screw a water-resistant wooden board (min. 30 mm thick) to the floor.
– The feet of the washing machine must be secured with holding brackets*.
* order no. see above
Installation on a platform with drawer*
– * order no.WMZ20455, WZ20455
Installing the appliance
Install the appliance before connecting it to the power supply.
Installation in a kitchenette (underneath the worktop or fitted in a cabinet)
– Recess width of 60 cm required.
– Only install the washing machine underneath a continuous worktop that is securely
connected to adjacent cabinets.
Scope of delivery
depending on model
Aqua Stop
Aqua Secure &
Hot water
Standard
Adapter 1/2''-3/4''
Covers
(depending on model)
Also required, depending on the connection:
– 1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon
page 4; water connection.
Useful tools
– Spirit level for installation.
– Wrenches
WAF 13: for loosening transport braces
page 3 and
WAF 17: for aligning appliance feet
page 5.
Hose and cable lengths
depending on model
Left-hand connection
or
Right-hand connection
100 cm
145 cm
~
~
145 cm
100 cm
~
~
90 cm
135 cm
~
~
Available from specialist dealers/the after-sales service:
– Extension for Aqua-Stop or cold-water inlet hose (approx. 2.50 m),
order no. WMZ2380, WZ10130, CZ11350, Z7070X0
– Longer inlet hose (approx. 2.20 m) for standard model.
1
Moisture inside the drum
Removing the transport braces
is due to final testing.
– Before using the appliance for the first time, make sure that you
completely remove transport braces and keep them for
subsequent transportation.
Mains cable
– If you need to transport the appliance at a later date, always re-affix
the transport braces to prevent damage to the machine.
– Store the screw and sleeve together.
Water outlet
Water inlet
1. Take the hoses out of the holders.
Elbow
for fixing the drainage
hose in place
2. Remove all 4 screws completely.
3. Remove all 4 transport braces completely and take the mains cable
out of the holders (depending on model).
4. Affix the covers.
Water connection
depending on model
– Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
– To prevent leaks or water damage, observe the instructions in this section.
– Caution: only operate the washing machine using cold drinking water (in case of models
featured for hot water: maximum temperature 60 ºC).
– Do not connect to the mixer tap of an unpressurised hot-water boiler.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
– If in doubt, have a technician connect the appliance.
2
Water connection
depending on model
Water inlet
Caution: do not bend, squash, modify or cut through
(otherwise its strength is no longer guaranteed).
Optimum water pressure in the supply network: 200 1,000 kPa (2 10 bar)
page 6.
– When the tap is on, the water flow is at least 10 l/min
(1-2 bar: 6 l/min; with 1 bar consumption parameters cannot be assure).
– If the water pressure is higher than this, a pressure reducing valve must be installed
Connection to the tap:
Aqua-Stop, Aqua-Secure, Standard:
Aqua Stop, Aqua-Secure
max.
max.
90°
90°
1. Connect the water inlet hose (hoses) to the tap (taps) 3/4" = 26,4 mm and to the solenoid
valves.
Caution: only tighten the screw connections by hand.
2. Open the water tap (taps) carefully, checking the leak tightness of the connection points.
Caution: the screw connection is under mains water pressure.
Connection in case of hot water
models:
COLD – Cold water
HOT – Hot water max. 60 °C (red)
Water outlet
Caution: do not bend or pull lengthways.
Height difference between the installation surface and the
drain:
min. 60 cm - max. 100 cm
Outlet in a sink:
Caution: secure the drain hose from slipping out.
Caution: the plug must not block drainage from the sink. During
pumping, check whether the water is draining away quickly
enough. The end of the drain hose must not be immersed in the
water pumped out. This risks water being sucked back into the
washing machine.
Drainage into a siphon:
Caution: the connection point must be secured with a hose
clamp, Ø 24-40 mm (exclusive dealers).
3
Connection to the
machine:
no necessary with Aqua-
Stop, fixed installation;
Standard
Aqua-Secure, Standard
4
4
Advertisement
Table of Contents
Related Manuals for Siemens Washing machine
Summary of Contents for Siemens Washing machine
- Page 1 Aqua Stop Aqua Secure & Hot water – Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed Standard completely remove transport braces and keep them for Caution: do not bend, squash, modify or cut through to frost or outdoors.
- Page 2 Product number Production number The washing machine must not wobble. Check the alignment of the washing machine with a spirit level and adjust Rely on the professionalism of the manufacturer. Please contact us. if necessary. Remove all covers and store them.
- Page 3 Aqua Secure & Hot water Standard – Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed to frost or outdoors. Mains cable – The washing machine could be damaged. Do not lift the appliance by protruding components (e.g.
-
Page 4: Removing The Transport Braces
60 cm - max. 100 cm – To prevent leaks or water damage, observe the instructions in this section. – Caution: only operate the washing machine using cold drinking water (in case of models Outlet in a sink: featured for hot water: maximum temperature 60 ºC). -
Page 5: Electrical Connection
2. Change the height by turning the appliance feet. Caution: all four appliance feet must be firmly on the ground. The washing machine must not wobble. Check the alignment of the washing machine with a spirit level and adjust if necessary. Remove all covers and store them. -
Page 6: After-Sales Service
Aqua-Stop warranty ......7 Read these instructions before switching on the washing machine. Also observe the separate Instruction manual.