Page 1 TECRA M4 TOSHIBA TECRA M4 Portable Personal Computer User’s Manual...
Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA M4 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
Page 3 Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, i.LINK...
Page 4 TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PTM40* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE...
Page 5: Region Selection
User’s Manual Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 6 User’s Manual Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Page 7: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 8: Fax Branding
User’s Manual Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone...
Page 9 User’s Manual The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Page 10 User’s Manual Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
Page 11 User’s Manual ■ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: ■ a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.
Page 12: General Conditions
User’s Manual General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
Page 13 User’s Manual Description on Laser specification The optical drive such as DVD-ROM drive, DVD-ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
Page 14 User’s Manual User’s Manual...
Page 15: Table Of Contents
TECRA M4 Table of Contents Preface Manual contents ......... xxiii Conventions.
Page 16 Table of Contents USB floppy disk drive........2-14 Optical media drives.
Page 17 Method 1: Changing the screen orientation using TOSHIBA Accelerometer Utilities ......4-11 Method 2: Changing the screen orientation using Cross Function Button .
Page 18 DLA for TOSHIBA ........
Page 19 Installing the battery pack ....... . 6-15 TOSHIBA Password Utility ....... . . 6-16 User password.
Page 20 TV ........... . . 8-13 Using the TOSHIBA Application button..... . 8-13 Changing the resolution .
Page 21 TOSHIBA support ........
Page 22 Table of Contents Disclaimers LCD*1 ..........10-1 CPU*2 .
Page 23: Manual Contents
This manual tells how to set up and begin using your TECRA M4 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 24: Conventions
Operating Basics, includes instructions on using the following devices: TOSHIBA Pointing Device, Tablet PC Pen and Reserve Pen, USB floppy disk drive, changing to the Tablet mode, changing the screen orientation, changing to the laptop mode, changing Slim Select Bay modules, optical media drives, Sound System, Modem, Wireless communication features and LAN.
Page 25: Key Operation
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 26 Preface xxvi User’s Manual...
Page 27: General Precautions
TECRA M4 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 28: Pc Card Overheating
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system.
Page 29: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 30: Software
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: User’s Manual...
Page 31 For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your PC documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in Chapter 9 Troubleshooting for more information.
Page 32 Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 33 Introduction Disks Hard disk drive*4 Available in three sizes. ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) Disclaimer (HDD Drive Capacity) 1 Gigabyte (GB) means 1000 × 1000 × 1000 = 1,000,000,000 bytes using powers of 10.
Page 34 Introduction DVD-ROM&CD-R/RW Some models are equipped with a full-size, DVD- drive ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R and CD- RW at maximum 24 speed.
Page 35 Introduction Built-in*1 14.1" TFT LCD screen, 16 M colors, with one of the following resolutions: SXGA+, 1400 horizontal × 1050 vertical pixels. Disclaimer (LCD) Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology.
Page 36 Introduction Supplied Tablet PC A pen enables data entry directly through the display screen. Reserve Pen A pen enables data entry directly through the display screen. Supplied pen uses a pen instead of Tablet PC Pen at the time of loss or breakage. Some computers in the series are equipped with a Reserve Pen.
Page 37 Introduction Multimedia Sound system Windows sound system compatible sound system provides internal speakers and microphone as well as jacks for an external microphone and headphone. Video-out jack The video out jack lets you transfer video data to external devices. Data output depends on the (S-Video) type of device connected to the S-Video cable.
Page 38 Introduction Bluetooth Some computers in this series are equipped with Bluetooth functions. Bluetooth wireless technology eliminates the need for cables between electronic devices such as computers and printers. Bluetooth provides fast, reliable, and secure wireless communication in a small space. Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible...
Page 39: Special Features
The lock screw is inserted in the unlock position when purchased. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Press this button to launch application Application button automatinally.
Page 40 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...
Page 41 Introduction ■ Maximum Turns on fan first, then if Performance necessary lowers CPU processing speed. ■ Performance Uses a combination of fan and lowering the CPU processing speed. ■ Battery optimized Lowers the CPU processing speed first, then if necessary turns on the Cooling Method.
Page 42: Utilities
“shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD- Video.
Page 43 Select Bay modules while the computer is on. To activate this utility, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also...
Page 44 Introduction TOSHIBA Mic Effect This utility provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. Refer to the Sound System section in Chapter 4, Operating Basics, for details. TOSHIBA Password This utility lets you set a password that restricts Utility access to the computer.
Page 45: Options
533) can easily be installed in the computer. Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. Universal AC If you use your computer at more than one site...
Page 46 External monitor port, Universal Serial Bus port (USB2.0) × 4, LAN jack, Modem jack, Serial port, Parallel port. The TECRA M4 does not support the PS/2 port and Serial port on the Advanced Port Replicator III. Tablet Multi Dock II...
Page 47: Slim Select Bay Options
Introduction Bluetooth SD card3 Bluetooth SD card is an optional accessory compatible with the SD card slot of this computer. You can buy the card from TOSHIBA dealer. Bluetooth USB A Bluetooth adaptor that has a USB connector. adaptor Wireless communications can be carried out with Bluetooth-compatible equipment by connecting to the USB port of the computer.
Page 48 Introduction 1-20 User’s Manual...
Page 49: The Grand Tour
TECRA M4 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Disclaimer (Non-applicatable Icons) Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not...
Page 50 The Grand Tour Wireless Slide this switch to the left to turn off Wireless LAN function. Slide it to the right to turn on the communication functions. switch Some models are equipped with a Wireless communication. ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device.
Page 51: Left Side
The Grand Tour Left side Figure 2-2 shows the computer’s left side. SD card indicator Security lock slot PC card slot SD card slot Cooling vents USB ports PC card eject button i.LINK (IEEE1394) port Infrared port Figure 2-2 The left side of the computer Cooling vents Cooling vents help CPU keep from overheating.
Page 52: Right Side
Right side Figure 2-3 shows the computer’s right side. TOSHIBA Tablet PC Pen slot Slim Select Bay Application Button TOSHIBA Application Button Lock Tablet PC Pen Figure 2-3 The right side of the computer User’s Manual...
Page 53: Back Side
If the computer is OFF, pressing this button starts the computer and launches the associated program automatically. The default is the default e-mail program. TOSHIBA Slide this switch in order to lock TOSHIBA Application Button Application Button. By locking, it prevents Lock pushing TOSHIBA Application Button accidentally.
Page 54 The Grand Tour Universal Serial Bus The Universal Serial Bus port is on the back side. (USB 2.0) port Refer to Left side section, for details. External monitor This external monitor port lets you connect an port external video display. Video-out jack Plug an S-Video cable into this jack for video-out.
Page 55: Underside
The Grand Tour LAN active indicator This indicator glows orange when data is being (orange) exchanged between the computer and the LAN. DC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer.
Page 56 The Grand Tour Be sure to lock the Slim Select Bay lock before you transport or carry the computer. Slim Select Bay lock One screw secures the Slim Select Bay lock. screw Docking interface This port enables connection of an optional Advanced Port Replicator III and Tablet Multi Dock II described in Chapter 8, Optional...
Page 57: Front With The Display Open
The Grand Tour ■ When you use your computer in a dusty area, the dusts accumulate on a cooling vent at the under side of your computer. The accumulated dusts cause insufficient heat dissipation. Clean the dusts off with vacuum cleaner. ■...
Page 58 The Grand Tour Display hinge The display hinge holds the LCD display panel at easy-to-view angles. LCD screen The LCD screen displays high-contrast text and graphics. The available resolution depends on the model. The computer's SXGA+ screen consists of 1400 × 1050 pixels. Refer to Display Controller and Modes section in Appendix B.
Page 59: System Indicators
Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is "enabled". Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.
Page 60 The Grand Tour DC IN The DC IN indicator glows in green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows in green when the computer is on.
Page 61: Keyboard Indicators
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 62: Usb Floppy Disk Drive
The Grand Tour USB floppy disk drive USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks. It connects to the USB port. Option or provided with some models. USB connector Disk-In-Use Indicator Floppy disk Eject button slot Figure 2-10 USB floppy disk drive USB connector Insert this connector to the USB port of your computer.
Page 63: Optical Media Drives
The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVD- ROM, DVD-ROM&CD-R/RW and DVD Super Multi. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical media drives...
Page 64: Dvds
The Grand Tour DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Formats The drives support the following formats: ■...
Page 65: Dvd Super Multi Drive
The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/ DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
Page 66: Ac Adaptor
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. And the adaptor converts AC power to DC power and reduces the voltage supplied to this computer.
Page 67 The Grand Tour Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.
Page 68 The Grand Tour 2-20 User’s Manual...
Page 69: Getting Started
TECRA M4 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 70: General Conditions
PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.
Page 71: Placement Of The Computer
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.
Page 72: Seating And Posture
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Figure 3-1 Posture and positioning of the computer ■...
Page 73: Work Habits
Getting Started Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user. ■...
Page 74: Other Things To Note
Operating the computer in Tablet mode TOSHIBA TECRA M4 computer can be used in two ways; ordinary laptop PC and Tablet PC. You can use the computer as Tablet PC that is operated with attached Tablet PC Pen by turning LCD display panel in 180 degrees and closing it.
Page 75 Getting Started ■ Do not drop the computer nor apply excessive impact on the computer. Do not leave the computer in an automobile where the computer is exposed to direct sunbeam. ■ Do not put the computer in Tablet mode in a bag. ■...
Page 76: Connecting The Ac Adaptor
Power and Power-Up Modes. ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
Page 77 Getting Started 1. Connect the power cord to the AC adaptor. Figure 3-3 Connecting the power cord to the AC adaptor (2-pin plug) Figure 3-4 Connecting the power cord to the AC adaptor (3-pin plug) The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model.
Page 78: Opening The Display
Getting Started Opening the display The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing. 1. Push down the display latch on the front of the computer to unlatch the LCD display panel. 2.
Page 79: Starting Up For The First Time
Getting Started 2. Slide and hold the computer’s power button toward the right. Power button Figure 3-7 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo.
Page 80: Hibernation Mode
For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.
Page 81: Standby Mode
3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5. Select the Setup Action window. 6. Enable the desired Hibernation settings for When I slide the power button and When I close the lid.
Page 82 Getting Started ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.
Page 83: Restarting The Computer
Getting Started 3. Slide the power button. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. When you turn the power back on, you can continue where you left when you shut down the computer.
Page 84: Restoring The Preinstalled Software From The Recovery Hdd
Getting Started 3. Turn on your computer to open Windows XP. 4. Insert the (first) blank media into the tray of the optical media drive. 5. Double click the Recovery Disc Creator Launcher icon on the Windows XP desktop, or Select the application from start Menu. 6.
Page 85: Restoring The Preinstalled Software From Your Creating Recovery Media
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
Page 86 Getting Started 3-18 User’s Manual...
Page 87: Operating Basics
Operating Basics This chapter gives information on basic operations including using the TOSHIBA Pointing Devices, Tablet PC Pen and Reserve Pen, USB floppy disk drive, changing to the Tablet mode, changing the screen orientation, changing to the laptop mode, changing Slim Select Bay modules, optical media drives, Sound System, Modem, Wireless communication features and LAN.
Page 88: Using The Accupoint
Operating Basics Two buttons below the Touch Pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.
Page 89: Replacing The Cap
Tablet PC Pen in a natural position and tap, press or trace on the screen lightly. Before you begin using the TOSHIBA TECRA M4 for the first time, you will need to calibrate the Tablet PC Pen. Refer to the Pointing Device section in Chapter 9, Troubleshooting.
Page 90 Operating Basics Eraser button You can use this button as an eraser when using the application software for graphics. The application software for texts enables you to select and delete characters with one-touch action. Pen button Acts as the clicking of the right touch pad control button.
Page 91: Removing The Tablet Pc Pen
Operating Basics TOSHIBA is not liable to the quality problem of the products due to the use of the Tablet PC Pen in an environment where above conditions are not satisfied because of the use by unspecified number of users.
Page 92: Single Tap
Short and worn pen point is difficult to pull out. Replace the pen point with refill before it becomes too short. ■ TOSHIBA recommends the customer to keep another pen set as a spare. You can buy the pen set from TOSHIBA dealer. User’s Manual...
Page 93: Removing The Reserve Pen
Tablet PC Pen. Use of the broken pen tip causes to make scratches on the LCD display panel. When the reserve refills have run out, purchase a new pen set from a TOSHIBA dealer. Removing the Reserve Pen Remove the Reserve Pen as described below.
Page 94: Changing To The Tablet Mode
Operating Basics Changing to the Tablet mode To change the laptop mode to the Tablet mode, follow the instructions below. Figure 4-9 Changing to the Tablet mode (1) ■ Place the computer on a stable, flat place such as a desktop and rotate the LCD display panel slowly, holding the panel at its lower part.
Page 95 Operating Basics 2. Rotate the LCD display panel clockwise slowly. Figure 4-10 Changing to the Tablet mode (2) Do not apply excessive rotating force to the LCD display panel. It causes damage of the LCD display panel. 3. Turn the display latch in 180 degrees to the down side. 4.
Page 96: Changing The Screen Orientation
Operating Basics 7. Press the LCD display panel downward softly. Display latch Slit Figure 4-12 Changing to the Tablet mode (4) Changing the screen orientation The orientation of desktop screen can be changed to one of the following four display modes: Secondary portrait Primary portrait Primary landscape...
Page 97: Method 1: Changing The Screen Orientation Using Toshiba Accelerometer Utilities
3D screen saver. Method 1: Changing the screen orientation using TOSHIBA Accelerometer Utilities When TOSHIBA Accelerometer Utilities is enabled, you can invoke the Start menu, switch active windows or launch predefined applications by shaking the computer vertically or horizontally, or tilting it.
Page 98: Method 2: Changing The Screen Orientation Using Cross Function Button
Figure 4-14 Shake the computer Method 2: Changing the screen orientation using Cross Function Button 1. Press Cross Function Button for more than one second. TOSHIBA Table Menu will appear. 2. Select the Internal Display of the Toshiba shortcut using Cross Function Button and press Cross Function Button.
Page 99: Changing To The Laptop Mode
Operating Basics You can set the orientation of the desktop screen just after rotating the display from [Start]-[All Programs]-[TOSHIBA]-[Tablet PC]-[TOSHIBA Rotation Utility] Changing to the laptop mode To change the Tablet mode to the laptop mode, follow the instructions below.
Page 100: Disconnecting Usb Floppy Disk Drive
DVD-ROM&CD-R/RW drive, DVD Super Multi drive, HDD adaptor, Secondary battery pack. To avoid injury, do not put your hand into the Slim Select Bay slot. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction for information on using this utility to change modules while the computer’s power is on.
Page 101: Inserting A Module
Operating Basics 6. Grasp the optical media drive and slide it out. The optical media drive and other Slim Select Bay modules can become hot with use. Be careful when removing the module. Slim Select Bay lock screw Slim Select Bay latch Optical media drive Figure 4-16 Removing the optical media drive Inserting a module...
Page 102: Using Optical Media Drives
Operating Basics Using optical media drives The text and illustrations in this section refer primarily to the optional media drive. However, operation is the same for other optical drive in the Slim Select Bay. The full-size drive provides high-performance execution of CD/ DVD-ROM-based programs.
Page 103 Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Figure 4-19 Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-20 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.
Page 104: Removing Discs
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. ■ Always keep fingers away from the sides of the tray when closing the tray of an optical drive (CD/DVD drive, CD-RW drive, Multi-drive or equivalent drive) to avoid pinching your fingers.
Page 105: How To Remove Cd/Dvd When The Disk Tray Will Not Open
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Figure 4-22 Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place.
Page 106: Writing Cds On Dvd-Rom&Cd-R/Rw Drive
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs.
Page 107: When Writing Or Rewriting
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
Page 108: Writing Cd/Dvds On Dvd Super Multi Drive
DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product.
Page 109: Before Writing Or Rewriting
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 110 Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0 or Version Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM) and 2.4 speed (DVD+R DL, Double Layer Recordable Drive only).
Page 111: When Writing Or Rewriting
Operating Basics ■ When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive. ■ Be sure to connect the AC adaptor before you write or rewrite. ■ Before you enter standby/hibernation mode, be sure to finish DVD-RAM writing.
Page 112: Recordnow! Basic For Toshiba
■ Always copy data from the HDD to the DVD-RAM. Do not use cut-and- paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...
Page 113: Data Verification
3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).
Page 114: How To Make A Dvd-Video
Operating Basics 4. Click the Advanced tab in the System Properties window. 5. Click the Settings icon in the "Performance" section. 6. Click the Advanced tab in the Performance Options window. 7. Click the Change icon in the "virtual memory" section. 8.
Page 115 Operating Basics ■ Do not change display settings while using WinDVD Creator. ■ Do not enter standby/hibernation mode while using WinDVD Creator. ■ Do not operate WinDVD Creator immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. ■...
Page 116: Media Care
Operating Basics 3. About Disc Manager ■ WinDVD Creator can edit one play list on a disc. ■ WinDVD Creator might show a different a thumbnail than you previously set in CE (Consumer Electronics) DVD-RAM recorder. ■ Using the Disc Manager, you can edit DVD-VR format on DVD- RAM, DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW.
Page 117: Floppy Disks
Operating Basics Floppy disks 1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2.
Page 118: Soundmax Control Panel
Operating Basics To adjust the volume or activate Mute, click start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control. In the Volume Control panel, you can use the slide bars to adjust the volume level or click Mute at the bottom of the panel. SoundMAX control panel The SoundMAX control panel lets you control additional functions for the Microphone Enhancement and Audio Power Management.
Page 119: Mic Effect
TOSHIBA Mic Effect will reduce these echoes generated on your computer. For more information on using the TOSHIBA Mic Effect, refer to its help. Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack.
Page 120: Properties Menu
Operating Basics 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4.
Page 121: Connecting
Operating Basics Connecting To connect the modular cable, follow the steps below. The modular cable for connecting a modem should use a commercially available cable. Connect the end of the modular cable with the core to the computer. ■ Connection to any communication line other than an analog phone line could cause a PC system failure.
Page 122: Disconnecting
TOSHIBA strongly recommend the customer to enable the WEP function. ■ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™ wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones.
Page 123: Bluetooth Stack For Windows By Toshiba
This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm all compatibility among any PC products and/or other electronic devices using Bluetooth other than TOSHIBA mobile PCs. Release Notes related to the Bluetooth Stack for ®...
Page 124: Wireless Communication Switch
The latest information regarding Operating System support, Language Support or available upgrades can be found on our web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or www.pcsupport.toshiba.com in the United States. Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch.
Page 125: Lan
Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Some models are equipped with a Gigabit Ethernet LAN. This section describes how to connect/disconnect to a LAN.
Page 126: Disconnecting Lan Cable
Operating Basics 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN connector LAN jack Figure 4-25 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub.
Page 127: Moving The Computer
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it recommends changing the function of HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter.
Page 128: Using The Hard Disk Drive (Hdd) Protection
Operating Basics Using the Hard Disk Drive (HDD) Protection There is a function for reducing the risk of damage on HDD in this computer. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks and similar signs in the computer, and automatically moves the HDD head to a safe position in order to reduce the risk of damage that could be caused by a head-to-disk contact.
Page 129: Toshiba Hdd Protection Properties
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start point to All Programs point to TOSHIBA point to Utilities and click HDD Protection setting.
Page 130: Detail Properties
Tablet mode (Battery). Detail Properties To open the Detail Properties window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Figure 4-28 Detail Properties Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
Page 131: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU Performance processing speed.
Page 132 Operating Basics 4-46 User’s Manual...
Page 133: The Keyboard
TECRA M4 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 134: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 135: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
Page 136 Fn, and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.
Page 137 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 138: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 139: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 140: Temporarily Using Normal Keyboard (Overlay On)
The Keyboard Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.
Page 141: Generating Ascii Characters
The Keyboard Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
Page 142 The Keyboard 5-10 User’s Manual...
Page 143: Power And Power-Up Modes
TECRA M4 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 144 Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) 2nd battery fully • Operates • No charge adaptor charged • No charge • LED: 2nd battery green connected • LED: 2nd Battery green DC IN green DC IN green 2nd Battery •...
Page 145 When the main battery is not charging. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a 2nd battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
Page 146: Power Indicators
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Slim Select Bay, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the 2nd battery.
Page 147: Power Indicator
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Indicates power is being supplied to the computer Green and the computer is turned on. Indicates power is being supplied to the computer Blinking orange while the computer is in Standby mode.
Page 148: 2Nd Battery Pack (Option)
The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always dispose of used battery packs in compliance with all applicable laws and regulations.
Page 149: Care And Use Of The Battery Pack
Power and Power-Up Modes The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 150 Power and Power-Up Modes 5. Never charge the battery pack by a method other than as instructed in the User's Manual. Doing so could cause a fire or explosion possibly resulting in serious injury. 6. Never connect the battery pack to a plug socket or a car cigarette plug socket.
Page 151 Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Use only battery packs recommended by TOSHIBA as replacements. 3. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted correctly and securely.
Page 152: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 153: Battery Charging Notice
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (4700mAh) about 5.5 to 13.0 about 3.0 2nd battery pack (3600mAh) about 4.0 to 9.5 about 3.0 RTC battery...
Page 154: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 155: Retaining Data With Power Off
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time Battery pack (4700mAh) about 5 days (Standby mode) about 40 days (Boot mode) 2nd battery pack (3600mAh)
Page 156: Replacing The Battery Pack
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator or Slim Select Bay indicator (if a Slim Select Bay 2nd battery pack is installed) flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.
Page 157: Installing The Battery Pack
Power and Power-Up Modes 6. Slide the battery release latch (➀) to free the battery pack for removal (➁), then slide out the battery pack. Battery release Battery pack latch Figure 6-2 Releasing the battery pack (2) 7. Return your computer to the upright position. Installing the battery pack To install a battery pack, follow the steps below.
Page 158: Toshiba Password Utility
Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: start ->...
Page 159: Supervisor Password
If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 160: Starting The Computer By Password
PC Pen. An * (asterisk) is displayed after “Password =” and one character is input for every tapping. Register your password to the computer in the laptop mode using the standard keyboard. Refer to TOSHIBA Password Utility, in this chapter for the detail. 6-18...
Page 161: Power-Up Modes
Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.
Page 162 Power and Power-Up Modes 6-20 User’s Manual...
Page 163: Hw Setup
TECRA M4 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config Parallel/Printer, USB and Button Setting.
Page 164: Power On Display
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
Page 165: Boot Priority
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM* and LAN (Default).
Page 166 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, 2nd HDD, CD-ROM, floppy disk drive (or SD memory card), Network (LAN), USB Memory boot.
Page 167 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD −>...
Page 168: Device Config
HW Setup Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled. When Switchable the computer is in use, CPU operation is automatically switched when necessary (Default).
Page 169 HW Setup PCI Express Link ASPM This feature lets you set the PCI Express power-saving configuration. Enables power-saving when the PCI Express Enabled device is not being used (Default). Disables power-saving for performance. Disabled Power-saving is enabled when the battery power Auto supply is used and the PCI Express device is not being used.
Page 170 HW Setup USB Memory BIOS Support Type Set the type of the USB memory as a startup device. Set the type of the USB memory to be equivalent to the HDD (Default). * Based on the [HDD] order in the [Boot Priority Options] item.
Page 171: Configuring The Execute-Disable Bit Capability And Tpm
Notes before using the BIOS Setup ■ In normal cases, changes in system configuration should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. If the configuration in the BIOS setup program is different from the configuration in the Windows utility, the configuration in the Windows utility takes priority.
Page 172: Execute-Disable Bit Capability
Not Available Available) (Default). System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. Security controller The security controller settings are available in SYSTEM SETUP (2/2).
Page 173: Diagnostic Mode
■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
Page 174: Fast Standby Hold Time
HW Setup Fast Standby Hold Time If Standby = Fast is selected, Fast Standby Hold Time can be used as an option. If powered by batteries in a Fast Standby mode, Not used the computer will immediately move to normal (Default) Standby mode.
Page 175: Optional Devices
TECRA M4 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ SD card ■...
Page 176: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 177: Removing A Pc Card
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not pop out.
Page 178: Formatting An Sd Memory Card
SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.
Page 179: Sd Card Care
8. Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the Utilities of Chapter 1, Introduction for details.
Page 180: Memory Expansion
When you remove a memory, please do not touch other portions of a computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost.
Page 181: Installing Memory Module
Optional Devices Installing memory module There are slots for two memory modules, one over the other. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning off the power section in Chapter 3, Getting Started.
Page 182: Removing Memory Module
Optional Devices ■ Be careful not to drop the screw inside the computer. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Seat the memory module cover and secure it with one screw. Be sure that the cover is closed firmly.
Page 183: Battery Pack
Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Page 184: Inserting
Optional Devices Inserting To install the 2nd battery pack in the adaptor, follow the steps below. 1. Fit the side of the 2nd battery pack opposite the connector into the adaptor. 2. Lay the battery into the adaptor. The latch should close automatically to secure the 2nd battery pack.
Page 185: Battery Charger
Optional Devices Battery Charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). Slim Select Bay HDD Adaptor(Black) You can increase your computer’s data storage capacity by installing an additional 40.0 billion bytes (37.26 GB), 60.0 billion bytes (55.89 GB), 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Slim Select Bay.
Page 186: Usb Fdd Kit
Optional Devices 3. Close the lid and slide the lock to the lock position. Figure 8-13 Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the computer’s Slim Select Bay slot, refer to Chapter 4, Operating Basics.
Page 187: Using The Toshiba Application Button
You can connect a television set to the Video-out jack on the computer. Follow the steps below. Using the TOSHIBA Application button 1. Connect the TV adaptor cable’s S-Video plug to the Video-out jack on the computer.
Page 188: Changing The Resolution
You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, Keyboard. To use "TV OUT" function by "TOSHIBA Application button", it is necessary to change the settings of "TOSHIBA Application button" in advance. To open "TOSHIBA Controls" properties, click Start, click Control Panel, click Printers and Other Hardware, select "TOSHIBA Controls", and set...
Page 189: I.link (Ieee1394)
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 190: Connecting
Optional Devices ■ Make sure data transfer has ended or turn off the computer, before you: ■ Connect/disconnect an i.LINK device to/from the computer. ■ Connect/disconnect an i.LINK device to/from another i.LINK device that is connected to the computer. Connecting 1.
Page 191: Advanced Port Replicator Iil
Modem jack, LAN jack, External monitor port, Video-out jack, i.LINK (IEEE 1394) port. ■ The TECRA M4 does not support the PS/2 port and Serial port on the Advanced Port Replicator III. The following ports and accessories are available on the Advanced Port Replicator III.
Page 192: Tablet Multi Dock Ii
Optional Devices Tablet Multi Dock II In addition to the ports available on the computer, the Tablet Multi Dock II provides, audio line-out jack. The Tablet Multi Dock II connects directly to the docking interface on the bottom of the computer. The AC adaptor connects the Tablet Multi Dock II to a power source.
Page 193: Security Lock
7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, Setup. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.
Page 194 Optional Devices 8-20 User’s Manual...
Page 195: Troubleshooting
TECRA M4 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 196: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 197: Hardware And System Checklist
Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
Page 198: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 199 Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing in green AC power If you have trouble turning on the computer with the AC adaptor connected,...
Page 200: Password
Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. Real Time Clock Problem Procedure The following The battery for RTC is wearing.
Page 201: Keyboard
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard. Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected. Press Fn + F10 and try typing again. Output to screen is Make sure the software you are using is not garbled...
Page 202: Hard Disk Drive
Troubleshooting Hard disk drive Problem Procedure Computer does not Check if a floppy disk is in the floppy disk drive or boot from hard disk a CD-ROM is in the optical media drive. Remove drive any floppy disk and/or CD-ROM and check Boot priority.
Page 203: Dvd-Rom&Cd-R/Rw Drive
Troubleshooting Problem Procedure Some CD/DVDs run The software or hardware configuration may correctly, but others do not be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM:...
Page 204 Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■...
Page 205: Dvd Super Multi Drive
Troubleshooting DVD Super Multi drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access Make sure the drive’s disc tray is securely closed. a CD/DVD in the drive Press gently until it clicks into place. Check whether the drive power is on.
Page 206: Usb Floppy Disk Drive
Troubleshooting USB floppy disk drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run The software or hardware configuration may be correctly but others do causing a problem.
Page 207: Pointing Device
Troubleshooting Pointing Device If you are using a USB mouse, also refer to the section in this chapter and to your mouse documentation. TOSHIBA Tablet PC Pen Problem Procedure On-screen pointer The system might be busy. If the pointer is...
Page 208: Usb Mouse
Troubleshooting Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume its Pad operation normal shape and try again to move it. The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility.
Page 209: Usb
Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab. 3.
Page 210: Memory Expansion
Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. Make sure the memory module installed in the memory slot is compatible with the computer. (Two beeps, a dash and a dot, for a If an incompatible module has been installed, defective memory follow the steps below.
Page 211: External Monitor
Troubleshooting External monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
Page 212: Modem
Troubleshooting Modem Refer to Appendix C, AT Commands and Appendix D, S-registers. Problem Procedure Communication Make sure the computer’s internal modem software can’t initialize settings are correct. Refer to Phone and Modem modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial...
Page 213: Lan
Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN does Make sure the AC adaptor is connected. The not work Wake-up on LAN function consumes power even when the system is off.
Page 214: Printer
Troubleshooting Printer Refer also to the Parallel printer sections in Chapter 8, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not turn on. Check that the printer is connected to an electric outlet.
Page 215: Disposing Of Pc And Pc Batteries
Troubleshooting Disposing of PC and PC batteries ■ Discard this PC in accordance with ordinances or rules of local regulations. For further information, contact your local government. ■ This PC contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them.
Page 216: Toshiba Support
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 217 Troubleshooting Outside of Europe In Europe Singapore Spain TOSHIBA Singapore Pte. Ltd. TOSHIBA Information Systems, ESPAÑA 438B Alexandra Road #06-01 Parque Empresarial San Fernando Alexandra Technopark Edificio Europa, l Planta, Singapore 119968 Escalera A 28830 Madrid United States of America...
Page 218 Troubleshooting 9-24 User’s Manual...
Page 219: Lcd*1
TECRA M4 Chapter 10 Disclaimers This chapter states the Disclaimers information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Disclaimer description is related to TOSHIBA computers. Descriptions related to this computer are marked with a blue *XX in this manual.
Page 220: Copy Protection*3
For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your PC documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in Chapter 9 Troubleshooting for more information.
Page 221: Wireless Lan/Atheros*6
Disclaimers Wireless LAN/Atheros The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.
Page 222: Safety Use For Tv Tuner*12
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 223: Appendix A Specifications
TECRA M4 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 328.0 (w) × 289.7 (d) × 36.9/38.4 (h) millimeters (not including parts that extend beyond the main body) Refer to User’s Manual or Information sheet about Weight.
Page 224 Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands...
Page 225 Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
Page 226 Specifications User’s Manual...
Page 227: Display Controller And Modes
TECRA M4 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The display controller supports VGA, SVGA and XGA modes at internal LCD display panel.
Page 228 Display Controller and Modes Table1 Video modes (VGA) Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K 16 of 256K Text Characters 2, 3 80 × 25 8 ×...
Page 229 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K 16 of 256K Grph...
Page 230 Display Controller and Modes Table 2 Video modes (SXGA+ model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K 1400 × 1050 256/256K 256/256K 1600 ×...
Page 231 Display Controller and Modes Table 2 Video modes (SXGA+ model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K 1400 × 1050 64K/64K 64K/64K 1600 ×...
Page 232 Display Controller and Modes Table 2 Video modes (SXGA+ model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M 1400 × 1050 16M/16M 16M/16M 1600 ×...
Page 233 Display Controller and Modes PowerMizer PowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways. To define the performance, select the menu options shown below: 1.Click start, click Control Panel and click Appearance and Themes. 2.Double-click the display icon to open the Display Properties window.
Page 234 Display Controller and Modes 6.Click the nView Display Settings and point to PowerMizer. Figure B-2 (Multiple Monitors) and NVIDIA GeForce Go 6200 T... The graphics processor is available in three options (Maximum Power Savings, Balanced, and Maximum Performance) in each of the AC power mode (AC Outlet) and the Battery power mode (Battery).
Page 235 TECRA M4 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 236 AT Commands Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default). Selects V.21 when the modem is at 300 bps. Selects Bell 103J when the modem is at 300 bps (default).
Page 237 AT Commands Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default). Modem goes off-hook. Result Codes: n=0,1 ERROR Otherwise Request ID information This command displays product information about the modem.
Page 238 AT Commands Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
Page 239 AT Commands Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 240 AT Commands Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
Page 241 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
Page 242 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
Page 243 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
Page 244 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
Page 245 TECRA M4 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
Page 246 S-registers Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
Page 247 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
Page 248 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units:...
Page 249 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
Page 250: At Command Set Result Codes
S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
Page 251 S-registers Connection at 28800 bps CONNECT 28800 EC Connection at 31200 bps CONNECT 31200 EC Connection at 33600 bps CONNECT 33600 EC Delay is in effect for the DELAYED dialed number Dialed number is blacklisted BLACKLISTED Blacklist is full BLACKLIST FULL *1: EC only appears when the Extended Result Codes configuration option is enabled.
Page 252 S-registers User’s Manual...
Page 253 TECRA M4 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 254 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
Page 255 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
Page 256 V.90 User’s Manual...
Page 257: Card Specifications
TECRA M4 Appendix F Wireless LAN Card Specifications Form Factor Mini PCI Type III ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Page 258 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 259 Wireless LAN 2457 * 2462 2467 2472 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
Page 260 Wireless LAN 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 *2 Refer to the sheet “Approved Countries/Regions for use” for the countries/regions that in which these channels can be used. User’s Manual...
Page 261: Ac Power Cord And Connectors
TECRA M4 Appendix G AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following...
Page 262 AC Power Cord and Connectors France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
Page 263: Parts Numbers
TECRA M4 Appendix H Parts Numbers The computer configuration and parts numbers, indicate the CPU, LCD, Memory, External VRAM, HDD, ODD. Bay, Wireless LAN, BT and TPM Security solution. Configurations Memory PentiumM 770 (2.13GHz) 14"TFT-SXGA+ 256MB PentiumM 760 (2.00GHz) 512MB PentiumM 750 (1.86GHz)
Page 264 Parts Numbers External VRAM HDD (Primary) ODD.Bay 64MB 40GB (5400rpm) DVD-ROM 128MB 60GB (5400rpm) CD-RW/DVD 80GB (5400rpm) DVD Super Multi DVD Super Multi (Double Layer) Wireless LAN TPM Security solution W-LAN Antenna Only BT Antenna only TPM Security integrated 802.11g 802.11ag User’s Manual...
Page 265 TECRA M4 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange...
Page 266 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Page 267 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
Page 268 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
Page 269 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 270 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 271 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 272 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 273 Glossary jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
Page 274 Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
Page 275 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 276 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
Page 277 (TFT) to drive each cell. TOSHIBA Tablet PC Pen: An input device for Tablet PC. User can write the character on a display screen with a digitizing function or tap to select the item appearing on the screen using the Tablet PC Pen.
Page 278 Glossary Glossary-14 User’s Manual...
Page 279 5-5 brightness increase 5-5 controller B-1 Battery hinge 2-10 2nd 6-6 opening 3-10 charging 6-10 DLA for TOSHIBA 1-16 4-27 extending life 6-13 Docking interface 1-8 indicator 2-12 Documentation list 1-2 location 2-7 DVD Super Multi drive 1-6...
Page 280 Index Equipment setup Hibernation 1-13 general conditions 3-2 Hot keys 1-11 placement 3-3 display brightness decrease Ergonomics lighting 3-4 display brightness increase seating and posture 3-4 work habits 3-5 display selection 5-5 instant security 5-4 power save mode 5-4 Floppy disk care 4-31 sound mute 5-3 Fn + Ctrl (enhanced keyboard standby 5-4...
Page 281 Index Keypad overlay 1-12 problems 9-6 Arrow mode 5-7 starting the computer by 6- Numeric mode 5-7 temporarily using normal supervisor 6-17 keyboard (overlay user 6-16 on) 5-8 PC card 1-8 temporarily using overlay inserting 8-2 (overlay off) 5-8 location of slot 2-3 turning on the overlays 5-7 problems 9-12 removing 8-3...
Page 282 1-9 SD card 9-12 mute hot keys 5-3 Self test 9-4 problems 9-16 Sound system 9-16 speakers 2-10 support from TOSHIBA 9- volume control 2-2 Standby 1-13 System start-up 9-3 setting 3-13 USB 9-15 System automatic 1-12 USB floppy disk drive 9-12...
Page 283 Index TOSHIBA PC Diagnostic Tool 1- TOSHIBA Power Saver 1-14 TOSHIBA SD Memory Boot Util- ity 1-15 TOSHIBA Zooming Utility 1-15 TV 8-13 Universal AC Adaptor 1-17 USB 1-8 problems 9-15 USB floppy disk drive 1-5 problems 9-12 using 4-13...
Page 284 Index Index-6 User’s Manual...

Toshiba TECRA M4 User Manual

Preface

Manual Contents

Conventions

General Precautions

Introduction

Equipment Checklist

Features

Special Features

Utilities

Options

The Grand Tour

Front with the Display Closed

Left Side

Right Side

Back Side

Underside

Front with the Display Open

System Indicators

Keyboard Indicators

USB Floppy Disk Drive

Optical Media Drives

AC Adaptor

Getting Started

Setting up Your Work Space

Other Things to Note

Operating the Computer in Tablet Mode

Connecting the AC Adaptor

Opening the Display

Turning on the Power

Starting up for the First Time

Turning off the Power

Restarting the Computer

Create Optical Recovery Discs

Restoring the Preinstalled Software from the Recovery HDD

Restoring the Preinstalled Software from Your Creating Recovery Media

Operating Basics

Pointing Device

Using the Tablet PC Pen and Reserve Pen

Changing to the Tablet Mode

Changing the Screen Orientation

Changing to the Laptop Mode

Using the USB Floppy Disk Drive

Changing Slim Select Bay Modules

Using Optical Media Drives

Writing Cds on DVD-ROM&CD-R/RW Drive

Writing CD/Dvds on DVD Super Multi Drive

Media Care

Sound System

Modem

Wireless Communications

Lan

Cleaning the Computer

Moving the Computer

Using the Hard Disk Drive (HDD) Protection

Heat Dispersal

The Keyboard

Typewriter Keys

Function Keys: F1

Soft Keys: Fn Key Combinations

Hot Keys

Windows Special Keys

Keypad Overlay

Generating ASCII Characters

Power and Power-Up Modes

Power Conditions

Power Indicators

Battery Types

Care and Use of the Battery Pack

Replacing the Battery Pack

TOSHIBA Password Utility

Tablet Mode

Power-Up Modes

Panel Power On/Off

System Auto off

HW Setup

Accessing HW Setup

HW Setup Window

Configuring the Execute-Disable Bit Capability and TPM

Optional Devices