Page 2
PCM-D1 Quantization General 16-bit linear, 24-bit linear Power requirements Frequency range (Input from the LINE IN jack DC IN 6V (AC 120V, 60 Hz) when recording/playing back) (0 to –2 dB) Four size AA (LR06) nickel metal Fs 22.05 kHz: 20 to 10,000 Hz hydride rechargeable batteries NH-AA Fs 44.10 kHz: 20 to 20,000 Hz...
Page 3
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
PCM-D1 SECTION 1 GENERAL This section is extracted from instruction manual. Overview (continued) Identifying parts and controls Front Right side...
Page 6
PCM-D1 Built-in microphones (page 22) z REC (recording) button/indicator (page 24) Analog level meters (page 25) Displays left and right volume levels of an DIVIDE button (page 30) audio signal input from microphones in N PLAY/ENTER button/indicator analog values. (pages 21, 28)
Page 7
PCM-D1 Overview (continued) Left side Display...
Page 8
PCM-D1 LINE OUT/optical DIGITAL OUT jack Peak meter (page 25) (page 29) Memory Stick indicator LINE IN jack (page 27) Displayed when the current memory is a “Memory Stick PRO (High Speed).” MIC ATT (microphone attenuator) switch (page 23) Folder number, track numbers Track numbers are displayed as “current...
PCM-D1 SECTION 2 DISASSEMBLY Note: This set can be disassemble according to the following sequence. 2-1. PANEL (FRONT) BLOCK ASSY (Page 10) 2-2. POWER BOARD (Page 10) 2-3. METER (VU) 2-4. VOL BLOCK ASSY (Page 11) (Page 11) 2-5. AUDIO (D/A) BOARD (Page 12) 2-6.
PCM-D1 Note: Follow the disassembly procedure in the numerical order given. 2-1. PANEL (FRONT) BLOCK ASSY 3 two screws (M1.7) 1 two cushions (panel) 5 panel (front) block assy 2 two cushions (panel) 4 two screws (M1.7) 2-2. POWER BOARD...
PCM-D1 2-9. CASE (MIC-F) 5 guard (MIC) 3 two cushions (MIC-R) 8 case (MIC-F) 2 two screws 4 two screws (M1.4) (M1.4) claw 1 two cushions (MIC-F) 6 two spacers (MIC-F) 7 two screws (M1.7) 2-10. MIC BLOCK ASSY 2 two screws (0 plate +P2 main EG grip M1.7)
PCM-D1 SECTION 3 TEST MODE This set provides the Test Mode that can be used for the following 1. Key Check check modes. A specific key is inputted by pressing it for input check and INT check. (It is verified that input of a key is confirmed and that KEY_XWAKE...
Page 17
PCM-D1 5. Lcd Check 15-1. F/W UpGrade method If the F/W need be updated for reasons such as modification of • This mode verifies that all LCD indicators are on and off, and it bugs after mass production, the F/W should be updated as follows: checks the PATTERN, vertical scroll and horizontal scroll displays.
PCM-D1 SECTION 4 ELECTRICAL ADJUSTMENT Level Meter Adjustment 1. Reproduce the WAVE file (DIGITAL DATA) (1kHz, –12dBs) standard signal. 2. Adjust RV2102 so that the pointer of the L-CH level meter indicates the center of “12”. 3. Adjust RV2202 so that the pointer of the R-CH level meter indicates the center of “12”.
PCM-D1 SECTION 5 DIAGRAMS Note on Schematic Diagrams: Note on Printed Wiring Boards: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics •...
PCM-D1 SECTION 6 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety.
PCM-D1 SECTION 7 AUDIO (A/D) ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark. the parts list may be different from the they are seldom required for routine service.
PCM-D1 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2005.12...