Advertisement
Quick Links
20W LED WALLPACK INSTALLATION INSTRUCTIONS
Thank you for buying
RAB LED lighting.
Comments? Call us at
888-RAB-1000, or email:
marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
RAB fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT.
Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
WARNING:
JUNCTION BOX MOUNT FOR
CONDUIT
For use on applications where conduit wiring is needed.
1. Loosen and remove (4) Lens Screws. Remove Door.
2. Loosen and remove (2) Housing Screws. Remove
Housing from Back Box. Keep Housing Gasket intact
for re-assembly.
3. Secure Back Box to the mounting surface using
hardware appropriate for that mounting surface.
4. Wire the fi xture using UL listed wire connectors
according to NEC and local codes. Apply sealant to all
unused conduit entry points.
5. Place Gasket between Back Box and Housing.
Re-mount Housing to Back Box. Check Housing
Gasket seal all around the Back Box.
6. Re-mount Door to Housing. Tighten (4) Lens Screws.
Check door gasket (not shown) seal.
7. Fixture is UL Listed for down and up lighting and may
be mounted in either position. Fixture may not melt
heavy snow accumulation in an uplight position.
CAUTION: For proper weatherproof function all gaskets
must be seated properly and all screws inserted and
tightened fi rmly.
Housing
Gasket
Back Box
Lens
Screws
Junction Box
SURFACE MOUNT FOR
RECESSED JUNCTION BOX
For use with recessed junction box and wiring.
1. Mount Surface Plate to fi xture with (4) Surface Plate
2. Use supplied crossbar. Mount Crossbar to recessed
3. Place Junction Box Gasket on back of the fi xture.
4. Wire fi xture to supply wires in recessed junction box
5. Use 1/4 x 20 stainless steel Mounting Screw to attach
6. Cover screw with Cap, provided.
7. Fixture is UL Listed for down and up lighting and may
Housing
Housing
Screws
Door
Surface Mount
Screws. There are two screws from the front and two
screws from the back. Make sure Housing Gasket
makes complete seal all the way around.
junction box with (2) screws.
Gasket should create seal against mounting surface.
according to wiring section.
fi xture to Crossbar. Tighten Mounting Screw.
be mounted in either position. Fixture may not melt
heavy snow accumulation in an uplight position.
CAUTION: For proper weatherproof function all gaskets
must be seated properly and all screws inserted and
tightened fi rmly.
Surface
Plate
Recessed
Junction Box
(not provided)
Crossbar
.
Housing
Junction
Gasket
Box Gasket
(4) Surface
Plate Screws
Mounting
Cap
Screw
Advertisement
Related Manuals for RAB WPLED20
Summary of Contents for RAB WPLED20
- Page 1 READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE RAB fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT.
-
Page 2: Troubleshooting
20W LED WALLPACK INSTALLATION INSTRUCTIONS JUNCTION BOX WIRING Universal voltage driver permits operation at 1. The Junction box has (4) conduit entry points on the 100V to 277VAC, 50 or 60Hz except those factory center of each side and (1) in the center back. ordered with a 120V photocell (/PC).