Cisco Firepower Management Center 1600 Getting Started Manual page 24

Hide thumbs Also See for Firepower Management Center 1600:

Hardware installation manual (44 pages)

page of 62

/ 62
Bookmarks

Connect Cables Turn On Power Verify Status for Versions 6.3 - 6.4

Each FMC-supported SFP+ transceiver (SFP-10G-SR and SFP-10G-LR) has an internal serial EEPROM that

is encoded with security information. This encoding allows us to identify and validate that the SFP transceiver

meets the requirements for the FMC chassis.

Note

Step 4

(Optional) eth3 management interface —Install any FMC-supported SFP+ transceiver and cable in this

10-Gigabit Ethernet SFP+ interface as needed. You can connect this interfaces to the same or different network

from your other management interfaces depending on your network needs. For more information about

management interfaces and network topology, see the

Each FMC-supported SFP+ transceiver (SFP-10G-SR and SFP-10G-LR) has an internal serial EEPROM that

is encoded with security information. This encoding allows us to identify and validate that the SFP transceiver

meets the requirements for the FMC chassis.

Note

Step 5

(Optional) USB port —Connect a keyboard to the USB port.

You can use this connection and a monitor connected to the VGA port to configure network settings for the

FMC before performing initial setup using the web interface; see

Using a Physical Connection for Software Versions 6.3 - 6.4, on page

Step 6

(Optional) VGA port —Connect a monitor to the VGA port.

The FMC sends console messages to the VGA port by default. You can use this connection and a keyboard

connected to a USB port to configure network settings for the FMC before performing initial setup using the

web interface; see

6.3 - 6.4, on page

Step 7

(Optional) Use the RJ-45 to DB-9 console cable supplied with the appliance (Cisco part number 72-3383-XX)

to connect a local computer to the FMC serial port. (You may need a DB-9-to-USB adaptor to connect to the

local computer.) You can use this connection for serial access (see

configure network settings for the FMC before performing initial setup using the web interface; see

Configure Network Settings Using a Physical Connection for Software Versions 6.3 - 6.4, on page

Step 8

(Optional) Use an ethernet cable to connect the CIMC port to a local network reachable from a computer

where you will run an IPMI utility for Lights-Out Management. See

for more information.

Step 9

Power supply—Use one of the supported power cords to connect the power supplies of the chassis to your

power source. For more information about supported power cords, see the

Center 1600, 2600, and 4600 Hardware Installation

Note

Step 10

Power—Press the Power button on the front of the chassis, and verify that the power status LED is on.

Step 11

Verify— Use the diagram in

LEDs reflect a good status.

Cisco Firepower Management Center 1600, 2600, and 4600 Getting Started Guide

Only FMC-supported SFP+ transceivers are compatible with the 10-Gb interfaces. Cisco TAC may

refuse support for any interoperability problems that result from using an untested third-party SFP

transceiver.

Only FMC-supported SFP+ transceivers are compatible with the 10-Gb interfaces. Cisco TAC may

refuse support for any interoperability problems that result from using an untested third-party SFP

transceiver.

(Optional) Configure Network Settings Using a Physical Connection for Software Versions

25.

We recommend connecting both power supplies on the FMC to provide redundancy protection. The

appliance generates a health alert if only one power supply is connected.

Front Panel LEDs and their States, on page 2

Cisco Firepower Management Center 1600, 2600, and 4600 Getting Started Guide

Firepower Management Center Configuration

(Optional) Configure Network Settings

Set Up Serial Access, on page

Set Up Lights-Out Management, on page

Guide.

25.

39) and to

(Optional)

Cisco Firepower Management

to check that the front-panel

Guide.

25.

This manual is also suitable for:

Firepower management center 2600 Firepower management center 4600

Cisco Firepower Management Center 1600 Getting Started Manual page 24

Related Manuals for Cisco Firepower Management Center 1600

Related Products for Cisco Firepower Management Center 1600

This manual is also suitable for: