Samsung SWA-9500S - Surround Sound System Manual

NOTES

• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Rear of the Main Unit)
• Design and specifications are subject to change without prior notice.

CONNECTING THE SWA-9500S TO A SOUNDBAR

1. Check the standby status after plugging into an electrical outlet

Plug the Surround Speakers power cord into an electrical outlet and into the Surround Speakers to turn on the Surround Speakers.

The LINK LED indicator (blue LED) on the Surround Speakers blinks. If the LED does not blink, refer to step 5.

2. Turn off the Soundbar

Turn off the Soundbar using the Soundbar's remote control or by pressing the (Power) button on the main Soundbar unit.

• The image of the Soundbar may differ from your Soundbar, depending on the model.

3. Configure "ID SET" using the Soundbar's remote control

Press the Up button on the Soundbar remote control for 5 seconds.

• The ID SET message appears on the Soundbar main unit's display for a short time and then disappears.
• After the ID SET process, the Soundbar power is automatically turned on.

• The image of the Soundbar may differ from your Soundbar, depending on the model.

4. Check if the LINK LED is solid blue (connection complete)

The LINK LED indicator stops blinking and glows a solid blue when a connection is established between the Soundbar and the Surround Speakers.

5. If the SWA-9500S does not connect, take the necessary steps according to the LED Indicator's status

LINK (Blue) On: Successfully connected (normal operation).

LINK (Blue) Blinking: Recovering the connection.

• Check if the power cable attached to the main Soundbar unit is connected properly or wait about 5 minutes.
• Repeat steps 2 through 4.

STANDBY (Red) On:
Standby (with the Soundbar main unit turned off).

• Check if the power cable attached to the main Soundbar unit is connected properly.

Connection failed.

1. Press the ID SET button on the back of the Surround Speakers with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue).
   
2. Repeat steps 2 through 4.

Red and blue Blinking: Malfunction

• See the contact information for the Samsung Service Center in this manual.

Installing the Surround Speakers on a Wall (Optional)

You can purchase wall mounts separately to install the surround speakers on a wall.

Wall mounts aren't sold by Samsung Electronics.

Notes for Wall Mounting the Surround Speakers

• Surround Speaker wall mounts must be able to support more than 17.6 lbs (8.0 kg).
• Hole size: 1/4 - 20 UNC threaded insert

Rear of the Left and Right Surround Speakers

• Standard Screw: 6.3 mm (0.3 inches) ,
  1.3 mm (0.1 inches) Pitch
• Length: 18.0 mm (0.7 inches) long
• Quantity: Left 1 EA / Right 1 EA

• Check the strength of the wall before you install the Wall Mount Brackets. If the strength is insufficient, make sure to reinforce the wall before installing the Wall Mount Brackets and the speakers on the wall.
• Samsung Electronics is not liable for any damage to the product due to the product being installed inappropriately.
• Take care not to install the speakers sideways or upside down.

COMPATIBLE MODELS

Compatible with select Samsung Soundbar. Please visit the Soundbar product page at www.samsung.com/support for more information.

Compatible model list is subject to change without further notice.

OPEN SOURCE LICENSE NOTICE

To send inquiries and requests for questions regarding open sources, contact Samsung Open Source (http://opensource.samsung.com)

SPECIFICATIONS AND GUIDE

Specifications

NOTES

• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate

QUESTIONS OR COMMENTS?

Country	Samsung Service Center	Web Site	Address
IN THE US	1-800-SAMSUNG (726-7864)	www.samsung.com/us/support	Samsung Electronics America, Inc. 85 Challenger Road Ridgefi eld Park, NJ 07660

© 2021 Samsung Electronics Co., Ltd. All rights reserved.