GE SBSD137 Installation Instructions Manual
Washer/dryer pedestal with drawer divider for washer models: gbvh5140; gbvh6260; gcvh6260; gcvh6600; ghdvh626; ghdvh670; wbvh5100; wbvh6240; wcvh6260; wcvh6600; whdvh626; whdvh660 for dryer models: dbvh510; dbvh512; dcvh515; dcvh660; dhdvh52; dhdvh66; pbv
Hide thumbs
Also See for SBSD137:
- Installation instructions manual (36 pages) ,
- Installation instructions manual (12 pages)
Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Installation
Instructions
Instructions en français : . . . . . . . . . . . .4
Instrucciones en español: . . . . . . . . . . .8
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
•
instructions for local inspector's use.
IMPORTANT
•
governing codes and ordinances.
• Note to Consumer – Keep these
instructions with your Owner's Manual
for future reference.
• Completion time – 1 to 2 hours
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation
is not covered under the Warranty.
CAUTION
weight of these products, and to reduce the
risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
• See washer and dryer installation
instructions for additional installation
requirements and guidelines.
KIT CONTENTS
4 Support Pads
4 Mounting Screws
Drawer Divider
— Save these
— Observe all
— Due to the size and
SBSD137, SBSD227
For Washer Models: GBVH5140, GBVH6260, GCVH6260, GCVH6600, GHDVH626,
GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600, WHDVH626
and WHDVH660
For Dryer Models: DBVH510, DBVH512, DCVH515, DCVH660, DHDVH52,
DHDVH66, PBVH415, PCVH565, PDVH515, PHDVH52 and PHDVH57
TOOLS YOU WILL NEED
Phillips Head
Screwdriver
9/16" Open End Wrench
or Adjustable Wrench
8 mm Socket Wrench
INSTALLATION PREPARATION
Remove the packaging.
The Drawer divider is taped at the top of the
shipping carton. Remove the divider and set
aside for final installation.
Flatten the product carton to use as a pad
to lay the washer or dryer down on its side.
Continue using the carton to protect the finished
floor in front of the installation location.
1
REMOVE THE LEVELING LEGS
Carefully lay the washer or dryer on its
A
side to access the leveling legs on the
bottom of the appliance.
IMPORTANT: Do not lay the washer or dryer
on its back! Do not remove the shipping
bolts on the back side of the washer. The
bolts must remain in place until the washer
is returned to an upright position.
B
Use an open-end wrench to remove the
washer or dryer leveling legs.
1
Back out and remove
all 4 leveling legs
Advertisement
Table of Contents
Related Manuals for GE SBSD137
Summary of Contents for GE SBSD137
-
Page 1: Installation Instructions
KIT CONTENTS 4 Support Pads 4 Mounting Screws Drawer Divider SBSD137, SBSD227 For Washer Models: GBVH5140, GBVH6260, GCVH6260, GCVH6600, GHDVH626, GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600, WHDVH626 and WHDVH660 For Dryer Models: DBVH510, DBVH512, DCVH515, DCVH660, DHDVH52, DHDVH66, PBVH415, PCVH565, PDVH515, PHDVH52 and PHDVH57... - Page 2 Installation Instructions PREPARE THE PEDESTAL Pull the drawer out as far as it will go. Remove screws from drawer slides. Slide drawer out of the base and set aside. FOR DRYERS ONLY: Locate the 4 support pads from the parts package.
-
Page 3: Remove Shipping Screws
Installation Instructions LEVEL THE WASHER OR DRYER Locate the 4 legs from the parts package and install. Stand the washer or dryer upright. Move it close to its final location. Make sure that the washer or dryer is level by placing a spirit level on top. Check side to side and front to back. -
Page 4: Instructions D'installation
CONTENU DE LA TROUSSE 4 coussinets de support 4 vis de montage Séparateur de tiroir SBSD137, SBSD227 Pour les modèles laveuses : GBVH5140, GBVH6260, GCVH6260, GCVH6600, GHDVH626, GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600, WHDVH626 et WHDVH660 Pour les modèles sécheuses : DBVH510, DBVH512, DCVH515, DCVH660,... - Page 5 Instructions d’installation RETIREZ LES PIEDS DE NIVELLEMENT Déposez avec soin la laveuse ou la sécheuse sur le côté pour accéder aux pieds de nivellement au bas de l’appareil. IMPORTANT: ne déposez pas la laveuse ou la sécheuse sur le dos ! Ne retirez pas les boulons d’expédition à...
- Page 6 Instructions d’installation INSTALLEZ LE SOCLE À LA LAVEUSE OU LA SÉCHEUSE Placez le socle contre le bas de l’appareil. Vérifiez pour vous assurer que le devant du tiroir est à l’avant de l’appareil. Alignez les trous du socle avec les trous au bas de l’appareil.
- Page 7 Instructions d’installation RÉINSTALLEZ LE TIROIR Vérifiez pour vous assurer que les glissières sont fermées. Glissez Séparateur le tiroir de tiroir dans l’ouverture. Alignez les supports du tiroir avec les glissières de chaque côté. Réinstallez les vis originales dans chaque glissière de tiroir. Resserrez les deux vis. Ouvrez entièrement le tiroir.
-
Page 8: Instrucciones Para La Instalación
CONTENIDO DEL KIT 4 planchuelas de soporte 4 tornillos de montaje Divisor de cajón SBSD137, SBSD227 Para los modelos de lavadoras: GBVH5140, GBVH6260, GCVH6260, GCVH6600, GHDVH626, GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600, WHDVH626 y WHDVH660 Para los modelos de secadoras: DBVH510, DBVH512, DCVH515, DCVH660,... - Page 9 Instrucciones para la instalación RETIRE LAS PATAS NIVELADORAS Apoye cuidadosamente la lavadora o secadora de lado para tener acceso a las patas niveladoras que se encuentran en la parte inferior del artefacto. IMPORTANTE: ¡no apoye la lavadora o secadora sobre su parte posterior! No retire los pernos de envío que se encuentran en la parte posterior de la lavadora.
- Page 10 Instrucciones para la instalación INSTALE EL PEDESTAL EN LA LAVADORA O SECADORA Coloque el pedestal contra la parte inferior de la unidad. Verifique que el frente del cajón quede hacia el frente de la unidad. Alinee los orificios del pedestal con los orificios en la parte inferior de la unidad.
-
Page 11: Finalice La Instalación
Instrucciones para la instalación VUELVA A INSTALAR EL CAJÓN Ver ifique que las correderas estén cerradas. Deslice el cajón en la abertura. Alinee los Divisor soportes de cajón del cajón con las correderas de cada lado. Vuelva a instalar los tornillos originales en cada una de las correderas del cajón. - Page 12 Printed in China 49-90321 Imprimé en Chine 175D1807P589 02-07 JR Impreso en China...