Hitachi C 7YA Handling Instructions Manual
Dust collection circular saw
Hide thumbs
Also See for C 7YA:
- Instruction and safety manual (68 pages) ,
- Handling instructions manual (23 pages) ,
- Technical and service manual (17 pages)
Table of Contents
Advertisement
Quick Links
Dust Collection Circular Saw
MODEL C 7YA
HANDLING INSTRUCTIONS
Note:
Before using this Power Tool, carefully read through these HANDLING
INSTRUCTIONS to ensure efficient, safe operation. It is recommended that
these INSTRUCTIONS be kept readily available as an important reference
when using this power tool.
Advertisement
Table of Contents
Related Manuals for Hitachi C 7YA
Summary of Contents for Hitachi C 7YA
-
Page 1: Handling Instructions
Dust Collection Circular Saw MODEL C 7YA HANDLING INSTRUCTIONS Note: Before using this Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference... -
Page 2: General Power Tool Safety Warnings
SYMBOLS When symbols are used on the machine, refer to the followings to understand the meaning. V ..............volts min ............. minutes A ..............amperes s ..............seconds Hz ..............hertz ..................no-load speed W ..............watts /min or Revolutions or reciprocations per minute .. -
Page 3: Further Safety Instructions For All Saws
d) Store idle power tools out of the reach of children h) Never use damaged or incorrect blade washers or bolt. and do not allow persons unfamiliar with the power The blade washers and bolt were specially designed for your saw, for optimum performance and safety tool or these instructions to operate the power tool. -
Page 4: Specifications
SAFETY INSTRUCTIONS FOR SAWS WITH PRECAUTIONS ON USING CIRCULAR SAW PENDULUM GUARD OR TOW GUARD 1. Do not use saw blades which are deformed or cracked. a) Check lower guard for proper closing before each use. 2. Do not use saw blades made of high speed steel. Do not operate the saw if lower guard does not move 3. -
Page 5: Adjusting The Saw Prior To Use
CAUTION: 2. Adjusting the cutting depth (Fig. 3) To avoid possible accident, remains always ensure To adjust cutting depth, loosen the clamp lever and, that the portion of work piece after cutting is while holding the base with one hand, move the securely anchored or held in position. -
Page 6: Mounting And Dismounting The Saw Blade
Wing Bolt (B), Lock Spring MOUNTING AND DISMOUNTING THE SAW Base BLADE CAUTION: To avoid serious accident ensure the switch is in the OFF position, and disconnect the plug from the receptacle. 1. Dismounting the saw blade (Fig. 7) Guide To replace the saw blade, push the lock lever, then (Rip Fence) loosen the hexagonal bolt with the wrench. -
Page 7: Use Of Dust Bag
The dust guide can change the direction of the USE OF DUST BAG discharge direction. Never point it in the direction of the worker. CAUTION: 1. Mounting the dust guide To avoid serious accident, ensure the switch is (1) Insert the dust guide’s thrusting mouth into the in the OFF position, and disconnect the plug from adapting mouth of the body. - Page 8 B: Code No. C: No. Used D: Remarks CAUTION Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the No. of carbon brush 17mm tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.
- Page 11 982027 HK1010 949455 302436 949425 302433 306082 992013 M5×14 319293 "59-62, 67" 6003VV 6003VVCMPS2L 949686 D6×40 319524 302697 M6×16.5 961807 947859 319291 308109 M6×8 319523 302440 319292 303631 M6×16.5 958523 M4×8 302441 302435 961482 990430 M4×10 319296 302444 319297 302423 957683 302427 M8×15.5...
- Page 12 Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99103213 M Printed in Malaysia...