List Of Warning Codes - Mitsubishi Electric MELSEC iQ-R Series User Manual
Motion module
Hide thumbs
Also See for MELSEC iQ-R Series:
- Programming manual (2110 pages) ,
- User manual (760 pages) ,
- Reference manual (498 pages)
Table of Contents
Advertisement
22.4
List of Warning Codes
Warning
Error
code
(System/
(Hexade
axis/axes
cimal)
group)
0D00H
Axis
0D01H
Axis
0D02H
Axis
0D03H
Axis/Axes
group
0D04H
Axis/Axes
group
0D05H
Axis/Axes
group
22 TROUBLESHOOTING
528
22.4 List of Warning Codes
Warning name
Error detail and cause
Absolute Position Data
• Axis type was changed.
Incorrect Warning
• Backup data for absolute
position restoration is incorrect.
• Homing has never been
executed after system started.
• Homing was started, but not
completed properly.
• Absolute position erase for
driver was detected.
• Machine homing was started,
but not completed properly.
• 'Absolute position erase' at
driver side was detected.
• 'Polarity(607Eh)' b7:position
polarity of driver object was
changed.
Start during Operation
Instruction that cannot start
Warning
during operation was executed.
JOG Command Input at
"JogForward" and "JogBackward"
Both Directions
became TRUE at the same time.
Warning
Speed Limit Value Over
The target speed is out of the
Warning
range when changing speed/
speed override coefficient.
• "AxisName.Pr.VelocityLimit_Po
sitive"
• "AxisName.Pr.VelocityLimit_Ne
gative"
• "AxesGroupName.Pr.VelocityLi
mit"
Acceleration Time Limit
Acceleration time exceeded 8400
Over Warning
seconds when changing speed/
acceleration (acceleration/
deceleration time)/speed override
coefficient/acceleration override
coefficient.
Deceleration Time Limit
Deceleration time exceeded 8400
Over Warning
seconds when changing speed/
deceleration (acceleration/
deceleration time)/speed override
coefficient/acceleration override
coefficient.
Detection
Operation at
timing (At
warning occurrence
start/
during
control
During
The current position is
control
restored with the same
content as the
incremental system, and
the homing request turns
TRUE.
During
Not start after the
control
execution of FB is
interrupted.
At start
• [At start] Not start after
During
the execution of FB is
control
interrupted.
• [During control]
Decelerates and
continues stop/wait
until the other JOG
command becomes
FALSE.
During
Continues the operation
control
at the previous speed.
During
Continues the operation
control
at the previous speed/
acceleration
(acceleration/
deceleration time).
During
Continues the operation
control
at the previous speed/
acceleration
(acceleration/
deceleration time).
Remedy
Perform the homing.
Start when axis is
StandStill.
Set it so that
"JogForward" and
"JogBackward" do not
become TRUE at the
same time.
Set the target speed
within the followings.
• "AxisName.Pr.Velocity
Limit_Positive"
• "AxisName.Pr.Velocity
Limit_Negative"
• "AxesGroupName.Pr.V
elocityLimit"
Set the speed/
acceleration
(acceleration/
deceleration time)/speed
override coefficient/
acceleration override
coefficient so that the
acceleration time will not
exceed 8400 seconds.
Set the speed/
deceleration
(acceleration/
deceleration time)/speed
override coefficient/
acceleration override
coefficient so that the
deceleration time will not
exceed 8400 seconds.
- Quick Links:
- Introduction
- Axis
- Chapter 1 Axis Setting
Hide quick links:
Advertisement
Table of Contents
