Cisco ME 3400 Command Reference Manual page 684
Ethernet access switch
Hide thumbs
Also See for ME 3400:
- Software configuration manual (1138 pages) ,
- Command reference manual (950 pages) ,
- Hardware installation manual (88 pages)
Table of Contents
Advertisement
vlan
The switch supports only Ethernet VLANs. You can configure parameters for FDDI and Token Ring
Note
VLANs and view the results in the vlan.dat file, but these parameters are not used.
•
are are-number: defines the maximum number of all-routes explorer (ARE) hops for TrCRF
VLANs. The range is 0 to 13. The default is 7.
•
backupcrf {enable | disable}: specifies the backup CRF mode for TrCRF VLANs.
•
bridge {bridge-number| type}: specifies the logical distributed source-routing bridge, the bridge
that interconnects all logical rings having this VLAN as a parent VLAN in FDDI-NET, Token
Ring-NET, and TrBRF VLANs. The range is 0 to 15. The default bridge number is 0.
exit: applies changes, increments the VLAN database revision number (VLANs 1 to 1005 only), and
•
exits VLAN configuration mode.
media: defines the VLAN media type.
•
•
mtu mtu-size: specifies the maximum transmission unit (MTU) (packet size in bytes). The range is
1500 to 18190. The default is 1500 bytes.
•
name vlan-name: names the VLAN with an ASCII string from 1 to 32 characters that must be unique
within the administrative domain. The default is VLANxxxx where xxxx represents four numeric
digits (including leading zeros) equal to the VLAN ID number.
no: negates a command or returns it to the default setting.
•
parent parent-vlan-id: specifies the parent VLAN of an existing FDDI, Token Ring, or TrCRF
•
VLAN. The range is 0 to 1005. The default parent VLAN ID is 0 (no parent VLAN).
private-vlan: configure the VLAN as a private VLAN community, isolated, or primary VLAN or
•
configure the association between private-VLAN primary and secondary VLANs. See the
private-vlan
remote-span: configure the VLAN as a Remote SPAN (RSPAN) VLAN. When the RSPAN feature
•
is added to an existing VLAN, the VLAN is first deleted and is then recreated with the RSPAN
feature. Any access ports are deactivated until the RSPAN feature is removed. Learning is disabled
on the VLAN. See the
ring ring-number: defines the logical ring for an FDDI, Token Ring, or TrCRF VLAN. The range is
•
1 to 4095.
said said-value: specifies the security association identifier (SAID) as documented in IEEE 802.10.
•
The range is 1 to 4294967294, and the number must be unique within the administrative domain.
The default value is 100000 plus the VLAN ID number.
shutdown: shuts down VLAN switching on the VLAN. This command takes effect immediately.
•
Other commands take effect when you exit VLAN configuration mode.
state: specifies the VLAN state:
•
Cisco ME 3400 Ethernet Access Switch Command Reference
2-658
ethernet is Ethernet media type (the default).
–
fddi is FDDI media type.
–
fd-net is FDDI network entity title (NET) media type.
–
tokenring is Token Ring media type or TrCRF.
–
–
tr-net is Token Ring network entity title (NET) media type or TrBRF media type.
command for more information.
remote-span
active means the VLAN is operational (the default).
–
suspend means the VLAN is suspended. Suspended VLANs do not pass packets.
–
Chapter 2 Cisco ME 3400 Ethernet Access Switch Cisco IOS Commands
command for more information.
OL-9640-07
Hide quick links:
Advertisement
Table of Contents
