Ivr Features; Ivr Terminology - Cisco AP776A - Nexus Converged Network Switch 5020 Configuration Manual
Cisco mds 9000 family cli configuration guide - release 4.x (ol-18084-01, february 2009)
Hide thumbs
Also See for AP776A - Nexus Converged Network Switch 5020:
- Command reference manual (1640 pages) ,
- Configuration manual (1486 pages) ,
- Reference (886 pages)
Table of Contents
Advertisement
Chapter 23
Configuring Inter-VSAN Routing
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
IVR Features
IVR supports the following features:
•
•
•
•
•
•
IVR Terminology
The following IVR-related terms are used in this chapter:
•
•
•
•
•
•
•
•
OL-18084-01, Cisco MDS NX-OS Release 4.x
Accesses resources across VSANs without compromising other VSAN benefits.
Transports data traffic between specific initiators and targets on different VSANs without merging
VSANs into a single logical fabric.
Shares valuable resources (like tape libraries) across VSANs without compromise.
Provides efficient business continuity or disaster recovery solutions when used in conjunction with
FCIP.
Is in compliance with Fibre Channel standards.
Incorporates third-party switches, however, IVR-enabled VSANs may have to be configured in one
of the interop modes.
Native VSAN—The VSAN to which an end device logs on is the native VSAN for that end device.
Current VSAN—The VSAN currently being configured for IVR.
Inter-VSAN routing zone (IVR zone)—A set of end devices that are allowed to communicate across
VSANs within their interconnected SAN fabric. This definition is based on their port world wide
names (pWWNs) and their native VSAN associations. Prior to Cisco SAN-OS Release 3.0(3), you
can configure up to 2000 IVR zones and 10,000 IVR zone members on the switches in the network.
As of Cisco SAN-OS Release 3.0(3), you can configure up to 8000 IVR zones and 20,000 IVR zone
members on the switches in the network.
Inter-VSAN routing zone sets (IVR zone sets)—One or more IVR zones make up an IVR zone set.
You can configure up to 32 IVR zone sets on any switch in the Cisco MDS 9000 Family. Only one
IVR zone set can be active at any time.
IVR path—An IVR path is a set of switches and Inter-Switch Links (ISLs) through which a frame
from an end device in one VSAN can reach another end device in some other VSAN. Multiple paths
can exist between two such end devices.
IVR-enabled switch—A switch on which the IVR feature is enabled.
Edge VSAN—A VSAN that initiates (source edge-VSAN) or terminates (destination edge-VSAN)
an IVR path. Edge VSANs may be adjacent to each other or they may be connected by one or more
transit VSANs. In
Figure
An edge VSAN for one IVR path can be a transit VSAN for another IVR path.
Note
Transit VSAN—A VSAN that exists along an IVR path from the source edge VSAN of that path to
the destination edge VSAN of that path. In
When the source and destination edge VSANs are adjacent to each other, then a transit
Note
VSAN is not required between them.
23-1, VSANs 1, 2, and 3 are edge VSANs.
Figure
23-1, VSAN 4 is a transit VSAN.
Cisco MDS 9000 Family CLI Configuration Guide
Inter-VSAN Routing
23-3
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
