Configuring And Activating Zones For Islb Initiators And Initiator Targets - Cisco AP776A - Nexus Converged Network Switch 5020 Configuration Manual
Cisco mds 9000 family cli configuration guide - release 4.x (ol-18084-01, february 2009)
Hide thumbs
Also See for AP776A - Nexus Converged Network Switch 5020:
- Command reference manual (1640 pages) ,
- Configuration manual (1486 pages) ,
- Reference (886 pages)
Table of Contents
Advertisement
Configuring iSLB
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
In addition, you can disable auto-zoning.
If you configure an IQN for an initiator target, then that name is used to identify the initiator target.
Otherwise, a unique IQN is generated for the initiator target.
To configure iSLB initiator targets, follow these steps:
Command
Step 1
switch# config terminal
switch(config)#
Step 2
switch(config)# islb initiator ip-address
10.1.1.3
switch(config-islb-init)#
Step 3
switch(config-iscsi-islb-init)# target
pwwn 26:00:01:02:03:04:05:06
switch(config-iscsi-islb-init)# target
pwwn 26:00:01:02:03:04:05:06 no-zone
switch(config-iscsi-islb-init)# target
device-alias SampleAlias
switch(config-iscsi-islb-init)# target
device-alias SampleAlias fc-lun 0x1234
iscsi-lun 0x2345
switch(config-iscsi-islb-init)# target
device-alias SampleAlias iqn-name
iqn.1987-01.com.cisco.initiator
switch(config-iscsi-islb-init)# target
device-alias SampleAlias sec-device-alias
SecondaryAlias
switch(config-iscsi-islb-init)# target
device-alias SampleAlias sec-pwwn
26:01:02:03:04:05:06:07
switch(config-iscsi-islb-init)# target
device-alias SampleAlias vsan 10
switch(config-iscsi-init)# no target pwwn
26:00:01:02:03:04:05:06
Configuring and Activating Zones for iSLB Initiators and Initiator Targets
You can configure a zone name where the iSLB initiators and initiator targets are added. If you do not
specify a zone name, the IPS manager creates one dynamically. iSLB zone sets have the following
considerations:
Cisco MDS 9000 Family CLI Configuration Guide
43-46
The VSAN identifier is optional if the target is online. If the target is not online, the VSAN
Note
identifier is required.
Purpose
Enters configuration mode.
Configures an iSLB initiator using its IPv4 address
and enters iSLB initiator configuration submode.
Configures the iSLB initiator target using a pWWN
with auto-zoning enabled (default).
Configures the iSLB initiator target using a pWWN
with auto-zoning disabled.
Configures the iSLB initiator target using a device
alias with auto-zoning enabled (default).
Configures the iSLB initiator target using a device
alias and optional LUN mapping.
Note
The CLI interprets the LUN identifier value
as a hexadecimal value whether or not the 0x
prefix is included.
Configures the iSLB initiator target using a device
alias and an optional IQN.
Configures the iSLB initiator target using a device
alias and an optional secondary device alias.
Configures the iSLB initiator target using a device
alias and an optional secondary pWWN.
Configures the iSLB initiator target using a device
alias and the VSAN identifier.
The VSAN identifier is optional is if the
Note
target is online. If the target is not online, the
VSAN identifier is required.
Removes the iSLB initiator target.
OL-18084-01, Cisco MDS NX-OS Release 4.x
Chapter 43
Configuring iSCSI
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
