Cisco 6500 Series Software Configuration Manual page 45
Hide thumbs
Also See for 6500 Series:
- Configuration manual (392 pages) ,
- Configuration note (212 pages) ,
- Installation manual (194 pages)
Table of Contents
Advertisement
Chapter 3
Configuring the Switch for the First Time
Configuring the Switch
When you reach and respond to the configuration dialog for the last installed interface, your interface
configuration is complete.
Step 3
Check and verify the entire list of configuration parameters, which should display on your console
terminal and end with the following query:
Use this configuration? [yes/no]:
A no response places you back at the enable prompt (#). You will need to reenter the setup command to
reenter your configuration. A yes response saves the running configuration to NVRAM as follows:
Use this configuration? [yes/no]: yes
[OK]
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
After you press the Return key, this prompt appears:
Router>
This completes the procedures for configuring global parameters and interface parameters in your
system. Your interfaces are now available for limited use.
If you want to modify the currently saved configuration parameters after the initial configuration, enter
the setup command. To perform more complex configurations, enter configuration mode and use the
configure command. Check the current state of the switch using the show version command, which
displays the software version and the interfaces, as follows:
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JS-M), Version 12.1(13)E1, EARLY DEPLOYM)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 06-Nov-02 13:57 by eaarmas
Image text-base: 0x40008C00, data-base: 0x41A72000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: c6sup2_rp Software (c6sup2_rp-JS-M), Version 12.1(13)E1, EARLY DEPLOYM)
Router uptime is 4 hours, 22 minutes
Time since Router switched to active is 4 hours, 22 minutes
System returned to ROM by power-on (SP by power-on)
System image file is "sup-bootflash:c6sup22-js-mz.121-13.E1"
cisco Catalyst 6000 (R7000) processor with 112640K/18432K bytes of memory.
Processor board ID SAD06210067
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
4 Virtual Ethernet/IEEE 802.3
interface(s)
48 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
381K bytes of non-volatile configuration memory.
16384K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Router#
Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide—Release 12.1 E
3-9
78-14099-04
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Cisco 6500 Series
Related Products for Cisco 6500 Series
- Cisco 6503 - Catalyst Firewall Security Sys
- Cisco 6503-E - Catalyst Chassis With Supervisor Engine 32 Switch
- Cisco 6504-E - Catalyst Chassis With Supervisor Engine 32 Switch
- Cisco 6506 - Catalyst Chassis Switch
- Cisco 6513 - Catalyst Switch
- Cisco Catalyst 6509
- Cisco Catalyst 6513-E
- Cisco Catalyst 6500-E Series