Cisco AP776A - Nexus Converged Network Switch 5020 Configuration Manual page 1005
Cisco mds 9000 family cli configuration guide - release 4.x (ol-18084-01, february 2009)
Hide thumbs
Also See for AP776A - Nexus Converged Network Switch 5020:
- Command reference manual (1640 pages) ,
- Configuration manual (1486 pages) ,
- Reference (886 pages)
Table of Contents
Advertisement
Chapter 41
Configuring FCIP
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
To create FCIP link endpoint in switch 1, follow these steps:
Command
Step 1
switch1# config terminal
switch(config)#
Step 2
switch1(config)# interface fcip 51
switch1(config-if)#
Step 3
switch1(config-if)# use-profile 10
Step 4
switch1(config-if)# peer-info ipaddr 10.1.1.1
Step 5
switch1(config-if)# no shutdown
To create an FCIP link endpoint in switch 2, follow these steps:
Command
Step 1
switch2# config terminal
switch(config)#
Step 2
switch2(config)# interface fcip 52
switch2(config-if)#
Step 3
switch2(config-if)# use-profile 20
Step 4
switch2(config-if)# peer-info ip
address 10.100.1.25
Step 5
switch1(config-if)# no shutdown
To create FCIP link endpoint in switch 1, follow these steps:
Command
Step 1
switch1# config terminal
switch(config)#
Step 2
switch1(config)# interface fcip 51
switch1(config-if)#
Step 3
switch1(config-if)# use-profile 10
Step 4
switch1(config-if)# peer-info ipaddr 10.1.1.1
Step 5
switch1(config-if)# no shutdown
To create an FCIP link endpoint in switch 2, follow these steps:
Command
Step 1
switch2# config terminal
switch(config)#
Step 2
switch2(config)# interface fcip 52
switch2(config-if)#
Step 3
switch2(config-if)# use-profile 20
Step 4
switch2(config-if)# peer-info ip
address 10.100.1.25
Step 5
switch1(config-if)# no shutdown
OL-18084-01, Cisco MDS NX-OS Release 4.x
Purpose
Enters configuration mode.
Creates an FCIP interface (51).
Assigns the profile (10) to the FCIP interface.
Assigns the peer IPv4 address information
(10.1.1.1 for switch 2) to the FCIP interface.
Enables the interface.
Purpose
Enters configuration mode.
Creates an FCIP interface (52).
Binds the profile (20) to the FCIP interface.
Assigns the peer IPv4 address information (10.100.1.25
for switch 1) to the FCIP interface.
Enables the interface.
Purpose
Enters configuration mode.
Creates an FCIP interface (51).
Assigns the profile (10) to the FCIP interface.
Assigns the peer IPv4 address information
(10.1.1.1 for switch 2) to the FCIP interface.
Enables the interface.
Purpose
Enters configuration mode.
Creates an FCIP interface (52).
Binds the profile (20) to the FCIP interface.
Assigns the peer IPv4 address information (10.100.1.25
for switch 1) to the FCIP interface.
Enables the interface.
Cisco MDS 9000 Family CLI Configuration Guide
Configuring FCIP
41-11
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
