Cisco 7609 Configuration Manual page 413
Cisco ios software configuration guide—12.1e
Hide thumbs
Also See for 7609:
- Installing (22 pages) ,
- Datasheet (5 pages) ,
- Frequently asked questions (5 pages)
Table of Contents
Advertisement
Chapter 32
Configuring PFC QoS
–
–
1p1q0t ingress LAN ports have this default drop-threshold configuration:
•
Frames with CoS 5 go to the strict-priority receive queue (queue 2), where the router drops incoming
frames only when the strict-priority receive-queue buffer is 100 percent full.
•
Frames with CoS 0, 1, 2, 3, 4, 6, or 7 go to the standard receive queue. The router drops incoming
frames when the receive-queue buffer is 100 percent full.
1p1q8t ports have this default drop-threshold configuration:
•
Frames with CoS 5 go to the strict-priority receive queue (queue 2), where the switch drops
incoming frames only when the strict-priority receive-queue buffer is 100 percent full.
•
Frames with CoS 0, 1, 2, 3, 4, 6, or 7 go to the standard receive queue, which uses WRED-drop
thresholds:
–
–
–
–
–
–
–
Note
78-14064-04
Using standard receive-queue tail-drop threshold 3, the router drops incoming frames with
CoS 4 when the receive-queue buffer is 80 percent or more full.
Using standard receive-queue tail-drop threshold 4, the router drops incoming frames with
CoS 6 or 7 when the receive-queue buffer is 100 percent full.
Using standard receive-queue WRED-drop threshold 1 for incoming frames with CoS 0, the
switch starts to drop frames when the receive-queue buffer is 40 percent full and drops all
frames with CoS 0 when the receive-queue buffer is 70 percent or more full.
Using standard receive-queue WRED-drop threshold 2 for incoming frames with CoS 1, the
switch starts to drop frames when the receive-queue buffer is 40 percent full and drops all
frames with CoS 1 when the receive-queue buffer is 70 percent or more full.
Using standard receive-queue WRED-drop threshold 3 for incoming frames with CoS 2, the
switch starts to drop frames when the receive-queue buffer is 50 percent full and drops all
frames with CoS 2 when the receive-queue buffer is 80 percent or more full.
Using standard receive-queue WRED-drop threshold 4 for incoming frames with CoS 3, the
switch starts to drop frames when the receive-queue buffer is 50 percent full and drops all
frames with CoS 3 when the receive-queue buffer is 80 percent or more full.
Using standard receive-queue WRED-drop threshold 5 for incoming frames with CoS 4, the
switch starts to drop frames when the receive-queue buffer is 60 percent full and drops all
frames with CoS 4 when the receive-queue buffer is 90 percent or more full.
Using standard receive-queue WRED-drop threshold 6 for incoming frames with CoS 6, the
switch starts to drop frames when the receive-queue buffer is 60 percent full and drops all
frames with CoS 6 when the receive-queue buffer is 90 percent or more full.
Using standard receive-queue WRED-drop threshold 7 for incoming frames with CoS 7, the
switch starts to drop frames when the receive-queue buffer is 70 percent full and drops all
frames with CoS 7 when the receive-queue buffer is 100 percent or more full.
You can configure the standard receive queue to use both a tail-drop and a WRED-drop
threshold by mapping a CoS value to the queue or to the queue and a threshold. The switch
uses the tail-drop threshold for traffic carrying CoS values mapped only to the queue. The
switch uses WRED-drop thresholds for traffic carrying CoS values mapped to the queue and
a threshold. See the
"Configuring Standard-Queue Drop Threshold Percentages" section on
page
32-54.
Cisco 7600 Series Router Cisco IOS Software Configuration Guide—12.1E
Understanding How PFC QoS Works
32-15
Advertisement
Table of Contents
Troubleshooting
