Cisco CATALYST 6000 Installation And Configuration Note page 42
Catalyst 6000 series content switching module
Hide thumbs
Also See for CATALYST 6000:
- Manual (52 pages) ,
- Product bulletin (4 pages) ,
- Installation note (18 pages)
Table of Contents
Advertisement
Configuration Examples
Command
Step 5
Router(config-slb-vserver)# virtual
192.158.38.30 tcp www
Step 6
Router(config)# ip slb vlan 3 server
Step 7
Router(config-slb-vserver)# ip addr
192.158.39.10 255.255.255.0
Step 8
Router(config-slb-vserver)# alias ip addr
192.158.39.20 255.255.255.0
Step 9
Router(config) ip slb vlan 9 ft
Step 10
Router(config)# ip slb fault_tolerance
group ft-group-number vlan 9
Step 11
Router(config)# vlan database
Step 12
Router(vlan)# vlan 2
Step 13
Router(vlan)# vlan 3
Step 14
Router(vlan)# vlan 9
Step 15
Router(vlan)# exit
1.
xEnter the exit command to leave a mode or submode. Enter the end command to return to the menu's top level.
2.
The no form of this command restores the defaults.
To configure the secondary (B) CSM for fault tolerance, perform this task (see
Command
Step 1
Router(config)# ip slb vlan 2 client
Step 2
Router(config-slb-vlan-client)# ip addr
192.158.38.40 255.255.255.0
Step 3
Router(config) ip slb vlan 9 ft
Step 4
Router(config-slb-vlan-client)# gateway
192.158.38.20
Step 5
Router(config)# ip slb vserver vip1
Step 6
Router(config-slb-vserver)# virtual
192.158.38.30 tcp www
Step 7
Router(config)# ip slb vlan 3 server
Step 8
Router(config-slb-vserver)# ip addr
192.158.39.30 255.255.255.0
Step 9
Router(config-slb-vserver)# alias
192.158.39.20 255.255.255.0
Step 10
Router(config)# ip slb fault_tolerance group
ft-group-number ab vlan 9
1. Enter the exit command to leave a mode or submode. Enter the end command to return to the menu's top level.
Catalyst 6000 Family Content Switching Module Installation and Configuration Note
42
Purpose
Create a virtual IP address.
Create the server-side VLAN 3 and enter the SLB
VLAN mode.
Assign the CSM IP address on VLAN 2.
Assign the default route for VLAN 2.
Define VLAN 9 as a fault-tolerant VLAN.
Create the Content Switching primary and
secondary (A/B) group VLAN 9.
1
Enter the VLAN mode
.
Configure a client-side VLAN2
Configure a server-side VLAN3.
Configure a fault-tolerant VLAN9.
Enter the exit command to have the configuration
take affect.
Purpose
Create the client-side VLAN 2 and enter the
1
SLB VLAN mode
.
Assign the Content Switching IP address on
VLAN 2.
Define VLAN 9 as a fault-tolerant VLAN.
Define the client-side VLAN gateway.
Create a virtual server and enter the SLB vserver
mode.
Create a virtual IP address.
Create the server-side VLAN 3 and enter the
SLB VLAN mode.
Assign the CSM IP address on VLAN 3.
Assign the default route for VLAN 2.
Create the CSM primary and secondary (A/B)
group VLAN 9.
2
.
Figure
12):
78-11631-02 Rev. A0
Advertisement
Chapters
Table of Contents
