Setting a DME Wipe
DME wipe patterns and modifiers are configured using the
menu.
This section describes the M/E-1 menu as an example.
Setting a DME Wipe Pattern
Selecting a DME wipe pattern
1
Open the DME wipe pattern selection menu.
In 1-channel mode, open the Home > M/E-1 > Bus/
Transition > DME Wipe > 1ch Pattern menu
(11109.41).
In 2-channel mode, open the Home > M/E-1 > Bus/
Transition > DME Wipe > 2ch Pattern menu
(11109.42).
In 3-channel mode, open the Home > M/E-1 > Bus/
Transition > DME Wipe > 3ch Pattern menu
(11109.43).
2
Press the button for a DME wipe pattern group.
The patterns in the selected group are displayed.
For 1-channel mode
Select from the following DME wipe pattern groups.
Slide / Squeeze: Slide and squeeze
Split / Door: Split and door
Flip Tumble: Flip tumble
Page Turn: Page turn
Roll: Roll
Frame I/O / P in P: Frame in/out and picture-in-
picture
Mosaic / Defocus: Mosaic and defocus
Resizer Slide / Squeeze: Resizer slide and squeeze
Resizer Frame I/O: Resizer frame in/out
For 2-channel mode
Select from the following DME wipe pattern groups.
Slide / Squeeze: Slide and squeeze
P in P: Picture-in-picture
Crop Slide: Crop slide
Page Turn: Page turn
Roll: Roll
Frame I/O: Frame in/out
Brick: Brick
For 3-channel mode
Select from the following DME wipe pattern groups.
Brick: Brick
3
Set the button for the target DME wipe pattern to the
on state.
Adjusting DME wipe pattern parameters
When the following patterns are selected, set the
parameters.
Squeeze (1-channel mode) pattern numbers 1032,
1033
Crop Slide (2-channel mode) pattern numbers
2661, 2662
No.
Parameter
1
Holding Level
2
Tolerance
a) Set relative to a transition start point of 0% and end point of 100%.
Page Turn (1-channel mode) pattern numbers
1301 to 1313, 1315 to 1318, 1341 to 1345
Page Turn (2-channel mode) pattern numbers
2701 to 2713, 2715 to 2718, 2741 to 2745
Roll (1-channel mode) pattern numbers 1321 to
1333, 1335 to 1338, 1346 to 1350
Roll (2-channel mode) pattern numbers 2721 to
2733, 2735 to 2738, 2746 to 2750
No.
Parameter
1
Radius
2
Magnitude
3
Start Angle
a) 0% is an effect like a turned page, 100% is normal curl, and 200% is radius
with double the normal curl.
b) –100.00 is rotation in the counterclockwise direction, +100.00 is rotation
in the clockwise direction, and 0.00 is no rotation.
Brick (2-channel mode) pattern numbers 2801 to
2804, 2811 to 2814
No.
Parameter
1
Side V Size X
2
Side V Size Y
3
Height
4
Center X
5
Center Y
a) Side V image horizontal center position. At –100.00, the center is at the
left edge of the screen. At +100.00, the center is at the right edge of the
screen.
b) Side V image vertical center position. At –100.00, the center is at the
bottom edge of the screen. At +100.00, the center is at the top edge of the
screen.
Frame I/O (2-channel mode) pattern numbers
2851 to 2854
No.
Parameter
1
Delay
115
Adjustment
Position for entering the dead band
a)
Width of the dead band
Adjustment
Radius of the turned page flap/
a)
rolled-up portion
Angle of rotation through course of
b)
transition
b)
Angle at start of transition
Adjustment
Side V horizontal scaling factor
Side V vertical scaling factor
Height of brick
a)
Horizontal center position
b)
Vertical center position
Adjustment
Timing for image selected on a
utility bus to enter the frame