Cisco ASR 1013 Hardware Installation Manual page 530
Asr 1000 series
Hide thumbs
Also See for ASR 1013:
- Installation manual (42 pages) ,
- Quick start manual (37 pages) ,
- Replacing (120 pages)
Table of Contents
Advertisement
Removing and Replacing the DIMM Memory Modules on the Cisco ASR 1006 Router and the Cisco ASR 1013 Router
SUMMARY STEPS
1. Remove the standby RP by performing the procedure described in the xref "Removing the Cisco ASR
1000 Series Route Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers"
section.
2. Remove the DIMM memory module from the standby RP by performing one of the following procedures:
3. Insert the new DIMM memory module on the standby RP by performing one of the following procedures:
4. Insert the standby RP by performing the procedure described in the xref "Removing the Cisco ASR 1000
Series Route Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers" section.
5. Verify the memory upgrade on the standby RP by running the following commands:
6. Use the redundancy force-switchover command to switch the upgraded standby RP to the active state.
The RP that was in the active state moves to the standby state.
7. Repeat Step 1 through Step 5 on the standby RP.
DETAILED STEPS
Step 1
Remove the standby RP by performing the procedure described in the xref "Removing the Cisco ASR 1000 Series Route
Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers" section.
Step 2
Remove the DIMM memory module from the standby RP by performing one of the following procedures:
• Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Step 3
Insert the new DIMM memory module on the standby RP by performing one of the following procedures:
• Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Step 4
Insert the standby RP by performing the procedure described in the xref "Removing the Cisco ASR 1000 Series Route
Processor from the Cisco ASR 1006, Cisco ASR 1004, and Cisco ASR 1013 Routers" section.
Step 5
Verify the memory upgrade on the standby RP by running the following commands:
Example:
Router# configure terminal
Router(config-red)# redundancy
Router(config-r-mc)# main-cpu
Router(config-r-mc)# standby console enable
Router(config-r-mc)# end
Router-stby# show version
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Experimental Version
Cisco ASR 1000 Series Router Hardware Installation Guide
496
• Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
• Removing and Replacing the Cisco ASR1000-RP1 DIMM Memory Modules
Removing the Cisco ASR1000-RP2 DIMMs
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Cisco ASR 1013
Related Products for Cisco ASR 1013
- Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1 Router
- Cisco ASR1000-RP2 - ASR 1000 Series Route Processor 2 Router
- Cisco ASR1002-5G-SEC/K9 - ASR 1002 VPN+FW Bundle Router
- Cisco ASR1002-5G-SHA/K9 - ASR 1002 Sec+HA Bundle Router
- Cisco ASR1004-10G-SHA/K9 - ASR 1004 Sec+HA Bundle Router
- Cisco ASR1004-20G-SEC/K9 - ASR 1004 VPN+FW Bundle Router
- Cisco ASR1006-10G-SEC/K9 - ASR 1006 VPN+FW Bundle Router
- Cisco ASR1006-10G-VPN/K9 - ASR 1006 VPN Bundle Router