Siemens SIMATIC S7-1200 System Manual page 1483
Hide thumbs
Also See for SIMATIC S7-1200:
- Function manual (527 pages) ,
- Manual (364 pages) ,
- System manual (338 pages)
Table of Contents
Advertisement
Table A- 179 Resistance
Range
Under range
minimum
150 Ω
n/a
300 Ω
n/a
600 Ω
n/a
Resistance values above the over-range minimum value are reported as +32767.
1
Note
The module reports 32767 on any activated channel with no sensor connected. If open wire
detection is also enabled, the module flashes the appropriate red LEDs.
When 500 Ω and 1000 Ω RTD ranges are used with other lower value resistors, the error
may increase to two times the specified error.
Best accuracy will be achieved for the 10 Ω RTD ranges if 4 wire connections are used.
The resistance of the connection wires in 2 wire mode will cause an error in the sensor
reading and therefore accuracy is not guaranteed.
Table A- 180 Noise reduction and update times for the RTD modules
Rejection frequency selec-
tion
400 Hz (2.5 ms)
60 Hz (16.6 ms)
50 Hz (20 ms)
10 Hz (100 ms)
To maintain module resolution and accuracy when the 400 Hz filter is selected, the integration time is 10 ms. This selec-
1
tion also rejects 100 Hz and 200 Hz noise.
Note
After power is applied, the module performs internal calibration for the analog-to-digital
converter. During this time the module reports a value of 32767 on each channel until valid
data is available on that channel. Your user program may need to allow for this initialization
time. Because the configuration of the module can vary the length of the initialization time,
you should verify the behavior or the module in your configuration. If required, you can
include logic in your user program to accommodate the initialization time of the module.
S7-1200 Programmable controller
System Manual, V4.2, 09/2016, A5E02486680-AK
Nominal range
Nominal range
low limit
high limit
0 (0 Ω)
27648 (150 Ω)
0 (0 Ω)
27648 (300 Ω)
0 (0 Ω)
27648 (600 Ω)
Integration time
10 ms
1
16.67 ms
20 ms
100 ms
A.11 Thermocouple and RTD signal modules (SMs)
Over
range
maximum
1
176.383 Ω ±0.05%
352.767 Ω ±0.05%
705.534 Ω ±0.05%
Update time (seconds)
4-channel module
4-/2-wire: 0.142
3-wire: 0.285
4-/2-wire: 0.222
3-wire: 0.445
4-/2-wire: 0.262
3-wire: .505
4-/2-wire: 1.222
3-wire: 2.445
Technical specifications
Normal range
Normal range accu-
accuracy
racy -20 °C to 60 °C
@ 25 °C
±0.1%
±0.1%
±0.1%
8-channel module
4-/2-wire: 0.285
3-wire: 0.525
4-/2-wire: 0.445
3-wire: 0.845
4-/2-wire: 0.524
3-wire: 1.015
4-/2-wire: 2.425
3-wire: 4.845
1483
Advertisement
Table of Contents
Related Manuals for Siemens SIMATIC S7-1200
Related Products for Siemens SIMATIC S7-1200
- Siemens SIMATIC PRO Extension Unit 12" Hardwired
- Siemens SIMATIC PRO Extension Unit 12" PROFINET
- Siemens SIMATIC PRO Extension Unit 12" PROFIsafe
- Siemens SIMATIC PRO Extension Unit 12" PN Advanced
- Siemens SIMATIC PRO Extension Unit 12" F PN Advanced
- Siemens SIMATIC NET SCALANCE W760 Series
- Siemens SIMATIC NET SCALANCE W720 Series
- Siemens SIMATIC 500 Series