Cisco Catalyst 2960 Software Configuration Manual page 722
Hide thumbs
Also See for Catalyst 2960:
- Configuration manual (2288 pages) ,
- Command reference manual (800 pages) ,
- Hardware installation manual (108 pages)
Table of Contents
Advertisement
Configuring IPv4 ACLs
Beginning in privileged EXEC mode, follow these steps to create an extended ACL:
Command
Step 1
configure terminal
Step 2a
access-list access-list-number
{deny | permit} protocol
source source-wildcard
destination destination-wildcard
[precedence precedence] [tos tos]
[fragments] [time-range
time-range-name] [dscp dscp]
Note
If you enter a dscp value,
you cannot enter tos or
precedence. You can enter
both a tos and a
precedence value with no
dscp.
or
access-list access-list-number
{deny | permit} protocol any any
[precedence precedence] [tos tos]
[fragments] [time-range
time-range-name] [dscp dscp]
Catalyst 2960 and 2960-S Switches Software Configuration Guide, Release 15.0(1)SE
31-10
Purpose
Enter global configuration mode.
Define an extended IPv4 access list and the access conditions.
The access-list-number is a decimal number from 100 to 199 or 2000 to 2699.
Enter deny or permit to specify whether to deny or permit the packet if
conditions are matched.
For protocol, enter the name or number of an IP protocol: ahp, eigrp, esp, gre,
icmp, igmp, igrp, ip, ipinip, nos, ospf, pcp, pim, tcp, or udp, or an integer in
the range 0 to 255 representing an IP protocol number. To match any Internet
protocol (including ICMP, TCP, and UDP), use the keyword ip.
This step includes options for most IP protocols. For additional specific
Note
parameters for TCP, UDP, ICMP, and IGMP, see steps 2b through 2e.
The source is the number of the network or host from which the packet is sent.
The source-wildcard applies wildcard bits to the source.
The destination is the network or host number to which the packet is sent.
The destination-wildcard applies wildcard bits to the destination.
Source, source-wildcard, destination, and destination-wildcard can be specified
as:
•
The 32-bit quantity in dotted-decimal format.
•
The keyword any for 0.0.0.0 255.255.255.255 (any host).
The keyword host for a single host 0.0.0.0.
•
The other keywords are optional and have these meanings:
precedence—Enter to match packets with a precedence level specified as a
•
number from 0 to 7 or by name: routine (0), priority (1), immediate (2),
flash (3), flash-override (4), critical (5), internet (6), network (7).
•
fragments—Enter to check non-initial fragments.
tos—Enter to match by type of service level, specified by a number from 0
•
to 15 or a name: normal (0), max-reliability (2), max-throughput (4),
min-delay (8).
time-range—For an explanation of this keyword, see the
•
Ranges with ACLs" section on page
dscp—Enter to match packets with the DSCP value specified by a number
•
from 0 to 63, or use the question mark (?) to see a list of available values.
In access-list configuration mode, define an extended IP access list using an
abbreviation for a source and source wildcard of 0.0.0.0 255.255.255.255 and
an abbreviation for a destination and destination wildcard of 0.0.0.0
255.255.255.255.
You can use the any keyword in place of source and destination address and
wildcard.
Chapter 31
Configuring Network Security with ACLs
31-15.
"Using Time
OL-26520-01
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
