Mitsubishi Electric MELSERVO-J5 User Manual page 287
Ac servo system
Hide thumbs
Also See for MELSERVO-J5:
- User manual (478 pages) ,
- Sample screen manual (128 pages) ,
- Introduction manual (112 pages)
Table of Contents
Advertisement
Static friction failure prediction function [G] [B]
■Friction failure prediction function method of use
Follow these procedures when using the static friction failure prediction function. For the static friction failure prediction
function, threshold that outputs a warning can be calculated automatically inside the servo amplifier using the automatic
threshold setting or set with servo parameters using the manual threshold setting. With the manual threshold setting, the
threshold that outputs a warning can be set to any value.
Startup the system.
When the maximum operation speed is under the rated
speed, set half the value of the maximum operation speed
in [Pr. PF31].
Set [Pr. PF41 Failure prediction - Servo motor total travel
distance] based on the initial stretch characteristics
presented by respective belt manufacturer.
Manual threshold setting
Set [Pr. PF34.5 Static friction failure prediction warning
selection] to "2" (Manual threshold setting).
Drive the servo motor.
The static friction and dynamic friction (at rated speed) are
estimated.
Save the data of the estimated static friction and dynamic friction.
Set a threshold with the following servo parameters.
[Pr. PF69 Static friction failure prediction - Average
characteristics]
[Pr. PF70 Static friction failure prediction - Standard deviation]
[Pr. PF40.4 Static friction failure prediction - Threshold
multiplication]
The setting of [Pr. PF40.5 Static friction failure prediction - Static
friction selection] is changed depending on the operation pattern.
Has the servo motor total travel
distance exceeded the value of
[Pr. PF41 Failure prediction -
Servo motor total travel distance]?
YES
Friction failure prediction is performed. If the static friction
value exceeds the threshold range, [AL. 0F7 Machine
diagnosis warning] will occur.
Start
Friction estimation function
Which function?
Friction failure prediction function
Threshold setting method?
Automatic threshold setting
Set [Pr. PF34.5 Static friction failure prediction warning
selection] to "1" (Automatic threshold setting).
Drive the servo motor.
The static friction and dynamic friction (at rated speed) are
estimated.
*1
Save the data of the estimated static friction and dynamic friction.
The setting of [Pr. PF40.5 Static friction failure prediction - Static
friction selection] is changed depending on the operation pattern.
Has the servo motor total travel
distance exceeded the value of
[Pr. PF41 Failure prediction -
Servo motor total travel distance]?
YES
NO
The threshold is automatically calculated.
The settings of [Pr. PF69 Static friction failure prediction - Average
characteristics] and [Pr. PF70 Static friction failure prediction -
Standard deviation] are changed based on the data of the
estimated static friction.
Has a threshold been created?
[Pr. PF34.5 Static friction failure prediction warning
selection] is set to "2" (Manual threshold setting).
End
Drive the servo motor.
The static friction and dynamic friction (at rated speed) are
estimated.
Save the data of the estimated static friction and dynamic friction.
*1
The saved data of static friction and dynamic friction
is used for troubleshooting [AL. 0F7.5 Static friction
failure prediction warning].
NO
*2
To calculate the threshold, after frictions have been
estimated, the equipment must be operated for 3
consecutive hours or more and operated in the
position mode, or velocity mode for a cumulative
time of 90 hours or more.
NO
YES
*1
Aging of the equipment is
estimated by comparing the
saved data of static friction
and dynamic friction with the
data being read while the
equipment is in operation.
4 APPLICABLE FUNCTIONS
4.5 Machine diagnosis
4
285
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric MELSERVO-J5
Related Products for Mitsubishi Electric MELSERVO-J5
- Mitsubishi Electric Melservo-J2-JR SERIES
- Mitsubishi Electric Melservo-J3 Series MR-J3-B
- Mitsubishi Electric MELSERVO-J4 series
- Mitsubishi Electric MELSERVO-J2-Super Series
- Mitsubishi Electric MELSERVO-J2M series
- Mitsubishi Electric MELSERVO-JE
- Mitsubishi Electric MELSERVO-JE MR-JE-C
- Mitsubishi Electric MELSERVO-J3W Series
- Mitsubishi Electric Melservo-J5 MR-J5 Series
- Mitsubishi Electric MELSERVO-J5 MR-J5-G-N1
- Mitsubishi Electric MELSERVO-J2 Series
- Mitsubishi Electric MELSERVO-J4 MR-J4 TM
- Mitsubishi Electric MELSERVO-J4 MR-J4-11KTM
- Mitsubishi Electric MELSERVO-J4 MR-J4-11KTM4
- Mitsubishi Electric MELSERVO-J4 MR-J4-22KTM
- Mitsubishi Electric MELSERVO-J4 MR-J4-22KTM4