Displaying Current And Minimum Required Fpd Image Versions - Cisco ASR 1000 Series Software Configuration Manual
Aggregation services routers sip and spa, cisco ios xe everest 16.5
Hide thumbs
Also See for ASR 1000 Series:
- Configuration manual (442 pages) ,
- Replacing (120 pages) ,
- Common criteria operational user guidance and preparative procedures (72 pages)
Table of Contents
Advertisement
Displaying Current and Minimum Required FPD Image Versions
With a manual upgrade, you must include the reload option to cause the SPA to reload automatically.
Note
See the
During an automatic upgrade, the Cisco ASR 1000 Series Routers will upgrade as many FPDs as possible at
a time. No user intervention is possible or necessary. The upgrade process will not stop until all FPD images
have been updated.
During manual upgrades, it is important to note that users can only specify upgrades for a single piece of
hardware each time the upgrade hw-module subslot [slot-number/subslot-number] command is entered. The
maximum of three simultaneous upgrades applies to manual upgrades as well. If you individually specify
multiple manual FPD upgrades, only three FPDs can be upgraded simultaneously and that can only occur
when the hardware is in different router slots. The FPD upgrade process will stop when all FPDs for the
specified hardware have been upgraded.
Displaying Current and Minimum Required FPD Image Versions
To display the current version of FPD images on the SPAs installed on your router, use the show hw-module
slot-number/subslot-number | all] fpd command, where slot-number is the slot number where the SIP is
installed, and subslot-number is the number of the SIP subslot where a target SPA is located. Entering the all
keyword shows information for hardware in all router slots.
The following examples show the output when using this show command.
The output display in this example shows that FPD versions on the SPAs in the system meet the minimum
requirements:
Router# show hw-module all fpd
==== ====================== ====== =============================================
Slot Card Type
==== ====================== ====== ================== =========== ==============
0/0 SPA-5X1GE-V2
---- ---------------------- ------ ------------------ ----------- --------------
0/1 SPA-8X1FE-TX-V2
---- ---------------------- ------ ------------------ ----------- --------------
0/2 SPA-2XCT3/DS0
---- ---------------------- ------ ------------------ ----------- --------------
1/0 SPA-2XOC3-POS
---- ---------------------- ------ ------------------ ----------- --------------
1/1 SPA-8XCHT1/E1
---- ---------------------- ------ ------------------ ----------- --------------
1/2 SPA-2XT3/E3
==== ====================== ====== =============================================
This example shows the output when using the slot-number/subslot-number argument to identify a particular
SPA:
Router# show hw-module subslot 1/0 fpd
==== ====================== ====== =============================================
Slot Card Type
==== ====================== ====== ================== =========== ==============
1/0 SPA-2XOC3-POS
==== ====================== ====== =============================================
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS
XE Everest 16.5
424
Manually Upgrading SPA FPD Images, on page
H/W
Ver.
1.1
1.1
1.1
1.0
1.1
1.0
H/W
Ver.
1.0
423.
Field Programmable
Current
Device: "ID-Name"
Version
1-GE I/O FPGA
1.10
1-FE I/O FPGA
1.1
1-ROMMON
2.12
2-I/O FPGA
2.7
3-T3 SUBRATE FPGA
1.4
1-I/O FPGA
3.4
1-ROMMON
2.12
2-I/O FPGA
2.7
1-ROMMON
2.12
2-I/O FPGA
1.0
3-E3 FPGA
1.4
4-T3 FPGA
1.4
Field Programmable
Current
Device: "ID-Name"
Version
1-I/O FPGA
3.4
Upgrading Field-Programmable Devices
Min. Required
Version
1.10
1.1
2.12
2.7
1.4
3.4
2.12
2.7
2.12
1.0
1.4
1.4
Min. Required
Version
3.4
OL-14127-17
Advertisement
Chapters
Table of Contents
Troubleshooting
