Showing Service Engine Status - Cisco ASR 1000 Series Software Configuration Manual
Aggregation services routers sip and spa, cisco ios xe everest 16.5
Hide thumbs
Also See for ASR 1000 Series:
- Configuration manual (442 pages) ,
- Replacing (120 pages) ,
- Common criteria operational user guidance and preparative procedures (72 pages)
Table of Contents
Advertisement
Configuring the Cisco WebEx Node for the ASR 1000 Series Aggregation Services Routers
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 2
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
Showing Service Engine Status
To show service engine status including a listing of the applications that are active, use the show hw-module
subslot service-engine status command as shown in the following example:
Router# show hw-module subslot 1/0 service-engine status
Service Engine is Cisco SPA-WMA-K9
Service Engine state: Steady (0x300)
Service Engine OS Version: 1.0.0, Application Version: 1.0.0
Application: WebEx Node (Web Conferencing)
Application Status: Online
Configuration:
Int ip address: 10.200.72.18 ,
GW ip address: 10.200.72.17
Nameserver 1: 10.100.4.10 ,
Hostname: spawma1, Domain name: cisco.com
WMA URL - https://wmabts.webex.com/wmams
WMA Token - 45484b3e-8ea5-41e5-b050-49409006d14e
WMA Passcode Name - cisco_test, key:0552055C271A4B5C4D5D424A5B5E007F
Note
Since the passcode and token are encrypted, the actual content is not displayed.
Verify that the service engine is reported in "Steady" state, and the Application Status is "Online." If the
Application Status is "Online," then verify that the indicated operation mode ("Web Conferencing" or "Voice
and Video Conferencing") is correct. If not, contact Cisco WebEx Technical Support to correct the problem.
If the Application Status field is "Offline" then the operation mode (indicated in parenthesis in "Application"
field) will show that it is not configured, as shown in the following sample output:
Router# show hw-module subslot 1/0 service-engine status
Service Engine is Cisco SPA-WMA-K9
Service Engine state: Steady (0x300)
Service Engine OS Version: 1.0.0, Application Version: 1.0.0
Application: WebEx Node (operation mode not configured)
Application Status: Offline
This occurs when the connection to the Cisco WebEx Data Center fails, and therefore provisioning information
about the operation mode can not be retrieved. For more information about provisioning, see the
with the WebEx Data Center and the Cisco WebEx Node Management System, on page
troubleshooting information, refer to the Troubleshooting the Cisco WebEx Node for the ASR 1000 Series
Aggregation Services Routers chapter.
OL-14127-17
19 packets input, 1302 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1091 packets output, 371289 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
mask: 255.255.255.252
Nameserver 2: 10.100.4.20
Showing Service Engine Status
Registering
353. For additional
Everest 16.5
363
Advertisement
Chapters
Table of Contents
Troubleshooting
