Verifying The Interface Configuration - Cisco ASR 1000 Series Software Configuration Manual
Aggregation services routers sip and spa, cisco ios xe everest 16.5
Hide thumbs
Also See for ASR 1000 Series:
- Configuration manual (442 pages) ,
- Replacing (120 pages) ,
- Common criteria operational user guidance and preparative procedures (72 pages)
Table of Contents
Advertisement
Verifying the Interface Configuration
Router# configure
terminal
Router(config)# interface atm 0/2/2
Router(config-if)# shutdown
Router(config-if)# end
Router# show interface atm 0/2/2
ATM0/2/2 is administratively down, line protocol is down
Hardware is SPA-3XOC3-ATM, address is 000d.2959.d5ca (bia 000d.2959.d5ca)
Internet address is 10.10.10.16/24
MTU 4470 bytes, sub MTU 4470, BW 599040 Kbit, DLY 80 usec,
Encapsulation ATM, loopback not set
Encapsulation(s): AAL0
4095 maximum active VCs, 1 current VCCs
VC idle disconnect time: 300 seconds
0 carrier transitions
Last input 01:01:16, output 01:01:16, output hang never
Last clearing of "show interface" counters 01:10:21
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 702176000 bits/sec, 1415679 packets/sec
Verifying the Interface Configuration
See the following sections to obtain configuration and operational information about the ATM SPA and its
interfaces. For additional information on using the commands to obtain information about the configuration
and operation of the ATM SPAs and interfaces, see the Troubleshooting the ATM SPAs chapter.
Verifying Per-Port Interface Status
Use the show interfaces atm command to display detailed status information about an interface port in an
ATM SPA that is installed in a Cisco ASR 1000 Series Router. The following example provides sample output
for interface port 1 (the second port) on the ATM SPA that is located in subslot 2, of the SIP that is installed
in slot 0 of a Cisco ASR 1000 Series Router:
The output of the show interfaces atm command can display configuration of AAL5 encapsulation, but
Note
only AAL0 is supported on the Cisco ASR 1000 Series Aggregation Services Routers.
Router# show interfaces atm 0/2/2
ATM0/2/2 is up, line protocol is up
Hardware is SPA-3XOC3-ATM-V2, address is 001a.3044.7522 (bia 001a.3044.7522)
MTU 4470 bytes, sub MTU 4470, BW 149760 Kbit, DLY 80 usec,
Encapsulation ATM, loopback not set
Keepalive not supported
Encapsulation(s): AAL5 AAL0
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS
XE Everest 16.5
86
reliability 255/255, txload 42/255, rxload 1/255
1000 packets input, 112000 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
2948203354 packets output, 182788653886 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
reliability 255/255, txload 1/255, rxload 1/255
Configuring the ATM SPAs
OL-14127-17
Advertisement
Chapters
Table of Contents
Troubleshooting
