Cisco ASR 1000 Series Software Configuration Manual page 475
Aggregation services routers sip and spa, cisco ios xe everest 16.5
Hide thumbs
Also See for ASR 1000 Series:
- Configuration manual (442 pages) ,
- Replacing (120 pages) ,
- Common criteria operational user guidance and preparative procedures (72 pages)
Table of Contents
Advertisement
Upgrading Field-Programmable Devices
Nov.28 11:30:15:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:30:31:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Router# upgrade hw-module subslot 0/1 fpg bundled
% Cannot get FPD version information for version checking. If a previous
upgrade attempt has failed for the target card, then a recovery upgrade
would be required to fix the failure.
% The following FPD(s) will be upgraded for SPA-4XOC3-POS (H/W ver =
1.0) in subslot 0/1:
================== =========== =========== ============
Field Programmable
Device:"ID-Name"
================== =========== =========== ============
1-I/O FPGA
================== =========== =========== ============
% Do you want to perform the recovery upgrade operation? [no]:y
% Cannot perform recovery upgrade operation because the target card is
not in a failed state. Please try again later.
Once the following error message is displayed, you can perform the recovery upgrade:
Nov.28 11:31:31:%SPA_OIR-3-SPA_POWERED_OFF:subslot 0/1:SPA 4xOC3 POS SPA powered off after
5 failures within 600 seconds
You must wait to see this error message before you attempt the upgrade.
Note
Perform the manual FPD image upgrade method using the upgrade hw-module subslot command to recover
from a corrupted image after the SPA has been powered off by the system. In this command, slot-number is
the slot where the SIP is installed, subslot-number is the subslot of the SIP where the SPA is located.
The following example displays the console output of a recovery upgrade operation:
Router# upgrade hw-module subslot 0/1 fpd bundled
% Cannot get FPD version information from SPA-4XOC3-POS in subslot 0/1.
If a previous upgrade attempt on the target card was interrupted, then the
corruption of FPD image might have prevented the card from coming online.
If this is the case, then a recovery upgrade would be required to fix the
failure.
(Hit ENTER to proceed with recovery upgrade operation) [confirm]
% The following FPD will be upgraded for SPA-4XOC3-POS (H/W ver = 1.0) in subslot 0/1:
% NOTES:
- Use 'show upgrade fpd progress' command to view the progress of the FPD
upgrade.
- Since the target card is currently in disabled state, it will be
automatically reloaded after the upgrade operation for the changes to
take effect.
% Do you want to perform the recovery upgrade operation? [no]: y
% Starting recovery upgrade operation in the background ...
(Use "show upgrade fpd progress" command to see upgrade progress)
Router#
*Nov 28 17:46:10.191:%FPD_MGMT-6-UPGRADE_TIME: Estimated total FPD image upgrade time for
SPA-4XOC3-POS card in subslot 0/1 = 00:00:50.
*Nov 28 17:46:10.233:%FPD_MGMT-6-UPGRADE_START: I/O FPGA (FPD ID=1) image upgrade in progress
for SPA-4XOC3-POS card in subslot 0/1. Updating to version 3.4. PLEASE DO NOT INTERRUPT
DURING THE UPGRADE PROCESS (estimated upgrade completion time = 00:00:50) ...
*Nov 28 17:46:55.948:%FPD_MGMT-6-UPGRADE_PASSED: I/O FPGA (FPD ID=1) image in the
SPA-4XOC3-POS card in subslot 0/1 has been successfully updated from version ?.? to version
3.4. Upgrading time = 00:00:45.715
*Nov 28 17:46:55.948:%FPD_MGMT-6-OVERALL_UPGRADE: All the attempts to upgrade the required
FPD images have been completed for SPA-4XOC3-POS card in subslot 0/1. Number of
successful/failure upgrade(s): 1/0.
*Nov 28 17:46:55.949:%FPD_MGMT-5-CARD_POWER_CYCLE: SPA-4XOC3-POS card in subslot 0/1 is
being power cycled for the FPD image upgrade to take effect.
OL-14127-17
Current
Version
?.?
================== =========== =========== ============
Field Programmable
Current
Device: "ID-Name"
Version
================== =========== =========== ============
1-I/O FPGA
================== =========== =========== ============
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
Upgrade
Estimated
Version
Upgrade Time
3.4
00:00:50
Upgrade
Estimated
Version
Upgrade Time
?.?
3.4
00:00:50
Performing an FPD Recovery Upgrade
Everest 16.5
429
Advertisement
Chapters
Table of Contents
Troubleshooting
Related Manuals for Cisco ASR 1000 Series
Related Products for Cisco ASR 1000 Series
- Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1 Router
- Cisco ASR1000-RP2 - ASR 1000 Series Route Processor 2 Router
- Cisco ASR-1000-SIP10
- Cisco ASR 1001
- Cisco ASR1002-5G-SEC/K9 - ASR 1002 VPN+FW Bundle Router
- Cisco ASR1004-20G-SEC/K9 - ASR 1004 VPN+FW Bundle Router
- Cisco ASR1002-10G-VPN/K9 - ASR 1002 VPN Bundle Router
- Cisco ASR1002-5G-HA/K9 - ASR 1002 HA Bundle Router