Performing An Fpd Recovery Upgrade - Cisco ASR 1000 Series Software Configuration Manual
Aggregation services routers sip and spa, cisco ios xe everest 16.5
Hide thumbs
Also See for ASR 1000 Series:
- Configuration manual (442 pages) ,
- Replacing (120 pages) ,
- Common criteria operational user guidance and preparative procedures (72 pages)
Table of Contents
Advertisement
Performing an FPD Recovery Upgrade
If the FPD upgrade operation is interrupted by a power failure or the removal of the SPA, it could corrupt the
FPD image. This corruption of the FPD image file makes the SPA unusable by the router and the system will
display the following messages when it tries to power up the SPA:
To find more information about FPD-related messages, check the system error messages guide for your
Note
Cisco IOS XE software release.
Nov.28 11:30:36:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:30:51:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Nov.28 11:30:56:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:31:11:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Nov.28 11:31:16:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:31:31:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Nov.28 11:31:31:%SPA_OIR-3-SPA_POWERED_OFF:subslot 0/1:SPA 4xOC3 POS
SPA powered off after 5 failures within 600 seconds
The show hw-module all fpd command can be used to verify that the SPA is using a corrupted FPD image.
In this example, the SPA in slot 0/1 is corrupted.
Router# show hw-module all fpd
==== ====================== ====== =============================================
Slot Card Type
==== ====================== ====== ================== =========== ==============
0/0 SPA-4XOC3-POS
---- ---------------------- ------ ------------------ ----------- --------------
0/1 SPA-4XOC3-PO<DISABLED>
---- ---------------------- ------ ------------------ ----------- --------------
0/2 SPA-1X10GE-L-V2
---- ---------------------- ------ ------------------ ----------- --------------
0/3 SPA-1X10GE-L-V2
==== ====================== ====== =================================================
Performing an FPD Recovery Upgrade
The recovery upgrade procedure can only be performed on a SPA that has been powered off by the system
after it has failed all of the retries attempted to initialize the SPA.
The following example displays the output of an attempt to perform a recovery upgrade before all the
initialization retries have been attempted for the SPA in subslot 0/1.
Note
Because a recovery upgrade is done at a more conservative speed, it may take more than the estimated
upgrade time.
Other factors can cause the system to ask "Do you want to perform the recovery upgrade operation?" Only
Note
answer y to this question if you have attempted an FPD upgrade that has failed due to a power failure or
a SPA removal.If you are prompted for this question without having previously had a failed upgrade
attempt for one of the aforementioned reasons, contact Cisco Technical Support.
Nov.28 11:29:55:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:30:10:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS
XE Everest 16.5
428
H/W
Field Programmable
Ver.
Device: "ID-Name"
1.0
1-I/O FPGA
1.0
????????????
1.0
1-10GE I/O FPGA
1.0
1-10GE I/O FPGA
Upgrading Field-Programmable Devices
Current
Min. Required
Version
Version
3.4
3.4
?.?
?.?
1.9
1.9
1.9
1.9
OL-14127-17
Advertisement
Chapters
Table of Contents
Troubleshooting
